• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.330-333
• /
• 2002

The substrate temperature is an important parameter in thin film deposition process. In this paper the effects of the substrate temperature on the properties of CuIn0.75Ga0.25Se2(CIGS) thin films are reported. Structure, surface morphology and optical properties of CIGS thin films deposited at various substrate temperatures have been investigated using a number of analysis techniques. X-ray diffraction (XRD) analysis shows that CIGS films exhibit a strong <112> preferred orientation. As expected, at higher substrate temperatures the films displayed a higher degree of crystallinity. The <112> peak was also enhanced and other CIGS peaks appeared simultaneously These results were supported by experimental work using Raman spectroscopy. The Raman spectra of the as-grown CIGS thin films show only the Al mode peak. The intensity of this peak was enhanced at higher deposition temperatures. Scanning electron microscopy (SEM) results revealed very small grains in films fabricated at 48$0^{\circ}C$ substrate temperature. When the substrate temperature was increased the average grain size also increased together with a reduction in the number and size of the voids. The deposition temperature also had a significant influence on the transmission spectra.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.6
• /
• pp.244-252
• /
• 2004

A stoichiometric mixture of evaporating materials for $CuInSe_2$ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films, $_CuInSe2$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (HWE) system. The source and substrate temperatures were $620^{\circ}C$ and $410^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $CuInSe_2$ single crystal thin films measured with Hall effect by van der Pauw method are $9.62\times10^{16}/\textrm{cm}^3$, 296 $\textrm{cm}^2$/Vㆍs at 293 K, respectively. The temperature dependence of the energy band gap of the $CuInSe_2$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g$(T) = 1.1851 eV -($8.99\times10^{-4} eV/K)T^2$(T + 153 K). The crystal field and the spin-orbit splitting energies for the valence band of the CuInSe$_2$ have been estimated to be 0.0087 eV and 0.2329 eV at 10 K, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the Δso definitely exists in the $\Gamma$6 states of the valence band of the $CuInSe_2$. The three photocurrent peaks observed at 10 K are ascribed to the $A_1-, B_1$-와 $C_1$-exciton peaks for n = 1.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.319-319
• /
• 2010

칼코젠계 태양전지의 광흡수층으로 사용되는 CuInSe2은 직접천이형 반도체로 광흡수계수가 $1{\times}105cm-1$로 매우 높고, 전기광학적 안정성이 우수하여 실리콘 결정질 태양전지를 대체할 고효율 태양전지로 각광받고 있다. 광흡수층의 밴드갭 에너지가 증가하면 태양전지의 개방전압(Voc)이 증가하여 광변환 효율을 향상시킬 수 있으므로, CuInSe2에서 In의 일부를 Ga으로 치환하여 에너지 밴드갭의 변화를 주는 연구가 많이 진행되고 있다. 그러나 화합물내의 Ga 조성비가 증가하면 단락전류(Jsc), 충진률(fill factor)이 낮아져 태양전지 효율을 저하시키게 되므로 CIGS 박막의 적절한 화합물 조성비를 갖도록 최적조건을 확립하는 것이 매우 중요하다. 본 실험에서는 광흡수층 형성을 위해 Sputtering법으로 금속 전구체를 증착하고, 고온에서 셀렌화 열처리를 수행하는 Sequential process(2단계 증착법)를 이용하였다. soda-lime glass 기판에 Back contact으로 Mo를 증착하고, 1단계로 CuIn0.7Ga0.3 조성비의 타겟을 이용하여 Sputtering법으로 $0.5{\sim}2{\mu}m$ 두께의 CIG 전구체를 증착하였다. 2단계로 CIG 전구체의 셀렌화열처리를 통하여 CIGS 화합물 구조의 박막을 형성시켰다. 이때 형성된 CIGS 화합물 박막의 두께는 동일하게 함으로써, 열처리온도에 의한 박막의 구조변화를 비교하였다. 증착된 CIGS 박막은 고온 엑스선회절분석을 통해 증착 두께와 온도 변화에 따른 CIGS 층의 구조 변화를 확인하고, 동일한 증착조건으로 Buffer layer, Window layer, Grid 전극을 형성하여 태양전지셀 특성을 평가함으로써 CIGS 태양전지 광흡수층의 결정구조에 따른 광변환 효율을 비교하였다.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.1
• /
• pp.16-21
• /
• 2013

CIGS (Cu-In-Ga-Se) films were deposited on the Mo coated soda lime glass (Mo/SLG) by RF magnetron sputtering using a single sintered target with different chemical compositions. Heat treatment of the CIGS films were carried out under three different conditions, 1step ($350^{\circ}C$ for 2 hour and $550^{\circ}C$ for 2 hour) and 2step ($350^{\circ}C$ for 1 hour and $550^{\circ}C$ for 1 hour). In the case of CIGS films post-annealed on 2step method, grain size remarkably increased compared to other methods, indicating that chemical composition [Cu/(Ga+In) = 1] of CIGS films was same as CIGS target. After heat treatment by 2step method, band gap energy of the CIGS film deposited at RF 80 W showed 1.4 eV which is broadly similar to identical band gap energy (1.2 eV) of CIGS film prepared by evaporation method. Therefore, 2step heat treatment method could be expected to low temperature process.

• Applied Microscopy
• /
• v.38 no.1
• /
• pp.63-72
• /
• 2008

The iterative wave-function reconstruction (IWFR) method developed by Allen et al. (2004) was reviewed with concern for its applicability. The high resolution transmission electron microscopy (HRTEM) studies of the materials such as GaAs, $YBa_2Cu_3O_7$ and $Al_2CuMg$ reported in the literature were utilized in this review. In this process the basis of validity, the limiting conditions and the information limit of this method were discussed. It was particularly noted that the phase contrast image of the exit plane wave evaluated from this method reveals not only $C_s$-corrected atomic resolution within information limit, but also strong tendency of contrast proportional to the magnitude of the atomic number of compositional atoms in a crystal.

• New & Renewable Energy
• /
• v.17 no.4
• /
• pp.36-45
• /
• 2021

To remove the Cu secondary phase remaining on the surface of a CIGSSe absorber layer manufactured by the two-step process, KCN etching was applied before depositing the CdS buffer layer. In addition, it was possible to increase the conversion efficiency by air annealing after forming the CdS buffer layer. In this study, various pre-treatment/post-treatment conditions wereapplied to the S-containing CIGSSe absorber layerbefore and after formation of the CdS buffer layer to experimentally confirm whether similareffects as those of Se-terminated CIGSe were exhibited. Contrary to expectations, it was noted that CdS air annealing had negative effects.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.125.2-125.2
• /
• 2011

CuInGaSe2 (CIGS)을 포함한 Chalcopyrite계 물질은 직접천이형 반도체이면서, ${\sim}1{\times}10^5cm^{-1}$ 이상의 광흡수계수를 보이며, 조성제어를 통한 밴드갭 조절이 가능해 차세대 고효율 박막태양전지재료로 매우 주목받고 있다. 최근, CIGS 박막태양전지 제조를 위해 CIGS 흡수층의 여러 가지 박막제조 공정들이 개발되고 있으나, 동시증착법과 소위 2단계법이라 일컬어지는 금속 전구체 스퍼터링 증착 후 셀렌화 공정을 가장 대표적인 공정이라 말 할 수 있다. 동시증착법은 실험실 수준의 소면적 셀에서 20%에 가까운 높은 효율의 CIGS 박막태양전지 제조에 성공하였음에도 불구하고, 상용화를 위한 대면적 셀 제조를 위해 해결해야 할 문제들이 아직 남아있다. 또한, 2단계법의 경우는 스퍼터링 공정을 기반으로 대면적 셀 제조에는 용이하나, CIGS/Mo 계면에서의 Ga 응집현상의 발생 및 셀렌화 공정에 사용되는 독성가스($H_2Se$)의 문제 등이 남아 있어 새로운 시각에서의 접근 방법이 요구되고 있다. 본 연구에서는 CIGS 4성분계 단일 타겟을 사용, RF 스퍼터링 공정을 통해 $200{\times}200mm^2$ 기판 위에 CIGS 박막을 제조하여 그 특성을 분석하였다. XRD 분석결과, 동시증착법에서 일반적으로 관찰되는 CIGS/Mo 계면에서의 $MoSe_2$ 상의 존재는 관찰되지 않았으며, CIGS 단일상의 다결정 박막이 제조되었음을 알 수 있었다. 또한, CIGS 박막제조 후, RTA 공정을 통해 CIGS 박막의 결정성이 향상됨을 관찰 할 수 있었으며, SIMS 분석결과, Mo층의 공정 조건에 따라 CIGS/Mo 계면에서의 금속원소 (In, Ga, Mo)의 상호확산이 크게 억제됨을 알 수 있었다. 그 외의 특성평가 결과들을 통하여 CIGS 4성분계 단일 타겟을 사용한 CIGS 박막태양전지 제조의 유용성에 대해 논의하고자 한다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.185-188
• /
• 2005

나노 입자 분무 기법을 이용한 $Cu(In,\;Ga)Se_2$ (CIGS) 광흡수층 제조 기법은 고진공 장치를 사용하지 않는다는 점에서 대면적 저가형 CIGS 태양전지 양산에 적합한 차세대 기술로 인식되고 있다. 그러나 일반적으로 스프레이 된 상태의 CIGS충 자체는 태양전지 제조에 적합하지 않은데 이는 스프레이 막의 다공성 구조 때문이다. 본 연구에서는 나노입자 분무 기법을 이용하여 증착한 CIGS 광흡수층막을 질소 또는 셀레늄 분위기에서 열처리함으로써 태양전지 제조에 적합한 치밀한 구조의 CIGS 광흡수충을 제조하고자 하였다. 실험 결과, 질소 분위기 $500^{\circ}C$의 온도에서 1시간 열처리하여도 CIGS 나노 입자의 성장은 거의 일어나지 않는 것으로 나타났다. 반면 셀레늄 분위기 $500^{\circ}C$의 온도에서 30분 열처리시 입자 크기가 $1{\mu}m$이상인 치밀한 광흡수층을 얻을 수 있었다. 본 결과는 CIGS 나노 입자의 입자 성장 반응에서 열에너지 단독에 의한 표면 에너지 감소 효과는 미미하며 셀레늄 증기의 역할이 더욱 크다는 것을 의미하는 것이다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.701-706
• /
• 2013

We have focused on the conversion efficiency of CIGS thin film solar cell prepared by co-evaporation method as well as the optimization of process condition. The total thickness of back electrode was fixed at 1 ${\mu}m$ and the structural, electric and optical properties of CIGS thin film were investigated by varying the thickness of Mo:Na bottom layer from 0 to 500 nm. From the experimental results, the content of Na was appeared as 0.28 atomic percent when the thickness of Mo:Na layer was 300 nm with compactly densified plate-shape surface morphology. From the XRD measurements, (112) plane was the strongest preferential orientation together with secondary (220) and (204) planes affecting to the crystallization. The lowest roughness and resistivity were 2.67 nm and 3.9 ${\Omega}{\cdot}cm$, respectively. In addition, very high carrier density and hole mobility were recorded. From the optimization of Mo:Na layer, we have achieved the conversion efficiency of 9.59 percent.

• Korean Journal of Materials Research
• /
• v.30 no.3
• /
• pp.131-135
• /
• 2020

Silver nanowire (AgNW) networks have been adopted as a front electrode in Cu(In,Ga)Se2 (CIGS) thin film solar cells due to their low cost and compatibility with the solution process. When an AgNW network is applied to a CIGS thin film solar cell, reflection loss can increase because the CdS layer, with a relatively high refractive index (n ~ 2.5 at 550 nm), is exposed to air. To resolve the issue, we apply solution-processed ZnO nanorods to the AgNW network as an anti-reflective coating. To obtain high performance of the optical and electrical properties of the ZnO nanorod and AgNW network composite, we optimize the process parameters - the spin coating of AgNWs and the concentration of zinc nitrate and hexamethylene tetramine (HMT - to fabricate ZnO nanorods. We verify that 10 mM of zinc nitrate and HMT show the lowest reflectance and 10% cell efficiency increase when applied to CIGS thin film solar cells.