• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3093-3098
• /
• 2010

The core-shell $SnO_2$@AO (A=Ni, Cu, Zn and Mg) films were prepared and the effects of coatings on photovoltaic properties were investigated. Studies on X-ray photoelectron spectroscopy, energy dispersive X-ray analysis and transmission electron microscopy showed the formation of divalent oxides on the surface of $SnO_2$ nanoparticles. It was commonly observed that all the dye-sensitized core-shell films exhibited higher photovoltage than the bare $SnO_2$ film. Transient photovoltage measurements confirmed that the improved photovoltages were related to the decreased time constants for electron recombination.

• Conservation Science in Museum
• /
• v.10
• /
• pp.1-13
• /
• 2009

A part of the bronze bell from Goryeo (918-1392) in the collection of Buyeo National Museum was missing, and it was noted to retain corrosion products and burial accretions. Chemical analysis showed that the chemical composition of the bronze bell is Cu (74.18%), Sn (9.58%), Pb (15.77%), and very small amounts of As, Fe, Sb, Bi, and Ag. It was noted that the microstructure of the bronze bell was mainly made up of α phase and α+δ eutectoid phase, and gray (S) and black (Pb segregation) prevailed. Conservation treatment has been done for the preservation of this bronze bell.

• The Research Journal of the Costume Culture
• /
• v.10 no.4
• /
• pp.433-440
• /
• 2002

Natural gardenia and Japanese pagoda tree have been known as them of the most widely used yellow vegetable dyes. Cotton and silk fabrics(KS K 0905) were chosen as specimens. Those were dyed with natural gardenia and Japanese pagoda tree. The conditions of dyeing were varied according to the kinds of mordants, using mordants or not and the concentrations of the natural dyes. Sn, Al, Fe and Cu were chosen for the mordants. 5%(owf), 10%(owf), 15%(owf) and 20%(owf) were used as for the concentration of the natural dyes. The color differences were measured by the Spectrometer(UV-VIS-NIR) before and after dyeing. The results are as follows: 1. Deeper colors were proportionately shown up to the concentration of the natural dye. 2. Silk was shown the higher dye affinity than the cotton at the same concentration of the dye. 3. The color difference between the Sn-mordanted specimens and the Al-mordanted specimens were significant. When the concentration of the dye increased, the colors got darker, specially in b* value. 4. The color difference between the Fe-mordanted specimens and the Cu-mordanted specimens were significant in L* value and b* value. 5. The deeper or lighter yellow were controllable under the concentration of the natural dye and the mordants. 6. The most effective and the economic concentration of the natural dye was 10% owf through the experiments.

• Fashion & Textile Research Journal
• /
• v.14 no.2
• /
• pp.320-330
• /
• 2012

The natural dyeing of cotton fabrics with guava leaf extract was investigated. The temperature and time of dyeing are $40^{\circ}C$ and $90^{\circ}C$ for eighty minutes, respectively. In addition, the dyebath has been set at pH 5. Sn pre-mordanted fabrics showed the highest K/S value. Regardless of dyeing temperature, K/S values were high when Al, Cu, Fe-mordanted fabrics were dyed in post-mordanting and Sn-mordanted fabrics were dyed in pre-mordanting. The K/S value of dyeing fabrics could be increased with repetitive dyeing and mordanting. Compared to untreated dyed fabrics, the K/ S values of fabrics which had been treated with soybean milk, chitosan and gall nut tannin were increased. The changed surface colors of fabrics that were treated with soybean milk, chitosan and gall nut tannin were Y, YR and achromatic colors. Fabrics dyed with alkaline water extract showed reddish color. Sn-mordanted fabrics dyed with acidic water extract showed vivid yellowish color, and Cu-mordanted fabrics dyed with ethanol extract showed yellowish green color. In case of Sn-mordanted fabrics, the washing fastness was level 4. The dry cleaning fastness also showed very excellent result with level 4-5. The rubbing fastness was better in dry rubbing than in wet rubbing of the fabrics. For the light fastness, all dyed fabrics showed low fastness. For antibacterial activity, the powder of guava leaf extract and the dyed fabrics with guava leaf extract showed 99.9% of high antibacterial activity. All dyed fabrics showed higher deodorization and UV protection rate than control fabric.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.77-77
• /
• 2009

ELV(; End of Life Vehicles)를 비롯한 최근 환경 동향은 자동차 전장 모듈에 대하여 다양한 무연 솔더 적용을 요구하고 있다. 특히 자동차 엔진룸과 트랜스미션은 가동 중 고온 및 진동의 지속적인 영향을 받기 때문에 이와 유사한 환경에서의 신뢰성 연구가 필요한 시점이다. 이에 본 연구에서는 Sn3.5Ag, Sn0.7Cu, Sn5.0Sb 솔더 조성에 대하여 복합환경 조건하에서 접합부 신뢰성을 평가하였다. 복합환경을 구현하기 위하여 $-40{\sim}150^{\circ}C$ 범위의 온도 사이클과 랜덤 진동을 동시에 인가하였으며, 진동 가속도 3G, 진동주파수는 10~1000Hz 로 설정하여 자동차 환경을 충족하였다. 복합시험의 1 cycle 은 20 시간이며, 총 120 시간의 시험 동안 진동의 영향 및 진동과 고온이 동시에 작용하였을 경우의 영향에 대해 비교하였다. 테스트 모듈 제작을 위해 450 um 의 솔더볼이 적용되었으며, 각 조성의 솔더볼을 이용하여 BGA test chip 제작하였고, 제작된 BGA test chip 은 다시 daisy chain PCB 위에 실장 및 리플로우 공정을 통해 접합되었다. 테스트 동안 In-situ 로 저항의 변화를 관찰하여 파단의 유무를 판단하였고 전자주사현미경을 통해 파괴 기전을 평가하였다. 복합시험 시간에 따른 전단강도를 측정하였으며, 각 조성에 대하여 상이한 전단강도 변화를 관찰하였다. 계면 IMC 형상은 전단강도 변화에 영향을 주었으며, 특히 높은 온도가 IMC 성장을 촉진시켜 전단강도 감소에 영향을 주었다. 본 복합환경 시험 조건에서는 Sn0.7Cu 가 가장 안정적이었으며, 파단면을 관찰한 결과 연성파괴 모드가 관찰되었다.

• Analytical Science and Technology
• /
• v.5 no.2
• /
• pp.191-197
• /
• 1992

An ancient Korean bronze dagger excavated from Yongjai-ri, Iksan-kun, presumed to be manufactured in the pre-historical age, was examined by means of chemical analysis, energy dispersive spectrometry, optical and scanning electron microscopy. Also the measurement of lead isotope ratios was carried out in order to predict the site where raw materials were produced. The composition was identified as 75.3% Cu, 17.1% Sn and 6.8% Pb which was a typical composition of Korean bronze dagger. The microstructure was consisted of ${\alpha}$ and (${\alpha}+{\delta}$) eutectoid. The (${\alpha}+{\delta}$) eutectoid can be easily corroded in comparison with ${\alpha}$. The segregation was frequently observed in the interior of the sample. According to the lead isotopes ratios, raw materials have possibility to be from North China.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.55-58
• /
• 1995

The effects of Ni contents in Cu base sintered friction material were studied. The contents of Ni were increased up to 9 wt% in the Cu-Sn matrix. The microstincture and tribological behavior of the friction material were examined. Pin on disk type of constant speed friction test rig were used to measure the friction and the wear rates. The results show that Ni addition increased the friction coefficients and decreased the wear rates of the materials. Relations between microhardness of the matrix and friction properties have been discussed. In addition optimum Ni content is recommended through the analysis of wear debris.

• Journal of Welding and Joining
• /
• v.29 no.5
• /
• pp.90-94
• /
• 2011

Ag metallic particles from nano-scale to submicron-scale are combined with organic solvent to provide fine circuits and interconnection. Ink-jet printing with Ag nano particle inks demonstrated the potentials of the new printed electronics technology. The bonding at the interface between the Ag wiring layer and the various substrates is very important. In this study, the details of interfaces in Ag wiring are investigated primarily by microstructure observation. By adjusting the materials and sintering conditions, nicely formed interfaces between Ag wiring and Cu, Au or organic substrates are achieved. In contrast, transmission electron microscope (TEM) image clearly shows interface debonding between Ag wiring and Sn substrate. Sn oxides are formed on the surface of the Sn plating. The formation of these is a root cause of the interface debonding.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.9-13
• /
• 2011

• Journal of Conservation Science
• /
• v.19
• /
• pp.67-72
• /
• 2006

The chemical compositions and lead isotope ratio of Poong-Tag(wind bell) bell excavated from Wanggyeong site, Gyeongju have analyzed by ICP and TIMS. The analysis result of chemical composition of Poong-Tag shows that it consists of 92:4 ratio of Cu:Sn. Other 8 minor elements(Pb, Zn, Fe, Ag, Ni, As, Sb and Co) show the concentration of below 0.2% respectively. This result means that Poong-Tag have made using highly purified Cu and Sn ore. For the study of provenance of raw material with the lead isotope ratio, the origin of the raw material of Poong-Tag can not be presumed owing to beyond the scope. The observation result of microstructure of Poong-Tag show the dendrite structure made through casting process. The chemical composition, microstructure, and lead isotope ratio of Poong-Tag excavated from Wanggyeong site, Gyeongju can be used as fundamental data to compare with other Poong-Tag of different regions and periods.