• Korean Journal of Materials Research
• /
• v.4 no.3
• /
• pp.280-286
• /
• 1994

As-grown $YBa_2Cu_3O_{7-x}$ films on MgO(100)substrates were prepated by a reactive co-evaporation method, and effects of activated oxygen plasma on the crystallinity and superconductivity at substrate temperature ranging from $450^{\circ}C$ to $590^{\circ}C$ were investigated. The film deposited under the activated oxygen plasma at the substrate temperature of $590^{\circ}C$ had a single crystal phase. Whereas, when films were deposited under only oxygen gas, they were not in perfect single crystal phase but with slight polycrystalline nature. When the substrate temperature was $590^{\circ}C$, $Tc_{zero}$'s were 83K and 80K for films with and without activated oxygen plasma, respectively. The critical temperature, the crystal structure and the surface morphology of as-grown films were found to be insensitive to the activated oxygen plasma which is introduced during deposition instead of oxygen gas, but the crystalline quality was improved somewhat by the introduction by the introduction of actvated oxygen plasma.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.2
• /
• pp.49-54
• /
• 2005

Flexible copper clad laminates (FCCL) fabricated by sputtering has advantages in fine pitch etching and dimensional accuracy than previous casting or laminating type FCCL, But its lower adhesion is inevitable technical challenge to solve for commercializing it. Chromium (Cr) which strongly reacts with O moiety was used as tie-coating layer in order to improve low adhesion between copper (Cu) and polyimide (PI). Sputtering raw polyimide (SRPI) and casting raw polyimide (CRPI) were used as substrates at this research. PI was pretreated by plasma before sputtering, and each sample was varied with RF power and Cr thickness on sputtering. Peel strength of the FCCL on SRPI was higher than that on CRPI. Adhesion had maximum value when 10 nm of Cr was deposited on SRPI by RF power of 50 W. It seems to be by the formation of Cu-Cr-O solid solution at the metal-PI interface.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.289-293
• /
• 1994

Thin films of YB $a_{2}$C $u_{3}$$O_{7-x}$ supercondYB $a_{2}$C $u_{3}$$O_{7-x}$uctor were prepared on (100) SrTi $O_{3}$ substrates by pulsed laser deposition using visible light laser. Q-switched Nd:YAG(532 nm, 30 ns) pulsed laser was used for deposition. The effects of substrate temperature and oxygen pressure during deposition on films were studied. Critical current density of 2.93*10$^{6}$ A/c $m^{2}$ at 77K and Tc(zero)=91.7K were obtained from the film prepared with Tsub=745.deg. C and $P_{02}$=200 mTorr. XRD analysis showed that the grown film has c-axis normal orientation to the substrate surface and has single phase. Surface morphology of the film has been improved by interfering the plume ejected from YB $a_{2}$C $u_{3}$$O_{7-x}$ target.arget.t.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.6
• /
• pp.575-579
• /
• 2004

Package reliability test was conducted to investigate the effect of solder paste composition at BGA Package. It was found that the shape and size of the phase form are affected by the processing parameters. The material have used to fill in the via was Sn/36Pb/2Ag and Sn/0.75Cu type solder paste. Sn/36Pb/2Ag and Sn/0.75Cu paste were fabricated on Tape-BGA substrates by screen printing process, and via ball mount data were characterized with variations of dwell time of 85 seconds at reflow peak temperature at 22$0^{\circ}C$ or 24$0^{\circ}C$. The test condition was MRT 30 $^{\circ}C$/60 %RH/96 HR. Failures formed of a ball-off in solder paste process were observed by using a Optical Microscope and SEM(Scanning Electron Microscope). It was concluded that intermetallic layer growth played important roles in increasing solder fatigue strength for addition of Ag composition. The degradation of shear strength of solder composition is discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.152-153
• /
• 2006

The new approach to buffer layer design for CIGS solar cells that permitted to reduce the buffer absorption losses in the short wavelength range and to overcome the disadvantages inherent to Cd-free CIGS solar cells was proposed. A chemical bath deposition method has been used to produce a high duality buffer layer that comprises thin film of CdS and Zn-based film. The double layer was grown on either ITO or CIGS substrates and its morphological, structural and optical properties were characterized. The Zn-based film was described as the ternary compound $ZnS_x(OH)_y$. The composition of the $ZnS_x(OH)_y$ layer was not uniform throughout its thickness. $ZnS_x(OH)_y$/CdS/substrate region was a highly intermixed region with gradually changing composition. The short wavelength cut-off of double layer was shifted to shorter wavelength (400nm) compared to that (520 nm) for the standard CdS by optimization of the double buffer design. The results show the way to improve the light energy collection efficiency of the nearly cadmium-free CIGS-based solar cells.

• Korean Journal of Agricultural Science
• /
• v.37 no.2
• /
• pp.191-197
• /
• 2010

The objective of this research was to determine the influence of the physical and chemical properties of root substrates used during the production of 'Maehyang' strawberry propaguleson the growth of the mother plants and the rate of daughter plant formation. Plants were cultured in plastic bags containing six different formulations of root substrates composed of: a) 50% coir dust and 50% perlite (5:5 by volume, A), b) 60% coir dust and 40% perlite (6:4, B), c) 70% coir dust and 30% perlite (7:3, C), d) 70% coir dust and 30% coconut chip (7:3 D), e) 60% coir dust and 40% coconut chip (60:40, E), or f) 50% sphagnum peat and 50% vermiculite (50:50, F). All media formulations contained a moderate level of base fertilizers. Physical and chemical properties of each formulation were determined before plant establishment and after 120 days of stock plant culture and runner production. Total porosity (TP) and container capacity (CC) of all substrate formulations were higher than 85% and 55%, respectively, allowing a suitable range of air and water holding characteristics. Formulation F provided the highest TP and CC values among the all substrate modifications evaluated. Substrate formulations A, B, C and F had higher electrical conductivity (EC) and $NO_3{^-}$-N concentrations than formulations D and E, when determined before and after plant culture. Formulations A, B, C, and F, having higher EC readings, also performed better as root substrates thanthe formulations D and E in increasing fresh and dry weights of the runners as well as the production of daughter plants per plant. The 'Maehyang' strawberry plants grown in the formulation F had the highest tissue N content, followed by those grown in substrate B, A, C, or D for 120 days after transplanting. Formulation F also facilitated accumulation of higher tissue phosphorus (P) and copper (Cu) contents compared to other treatments. Results of this experiment suggest that the chemical properties, rather than physical properties, of root substrates had a major influence on the growth of mother plants and the occurrence of healthy daughter plants during the bag-culture phase of propagation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.3
• /
• pp.107-112
• /
• 2010

The Cu$(In_{1-x}Ga_x)Se_2$ is the absorber material for thin film solar cell with high absorption coefficient of $1{\times}10^5cm^{-1}$. In the case of CIGS, the movable energy band gap from $CuInSe_2$ (1.00 eV) to $CuGaSe_2$ (1.68 eV) can be acquired while controlling Ga contain ratio. Generally, the co-evaporator method have used for development and fabrication of the CIGS absorption layer. However, this method should need many steps and lengthy deposition time with high temperature. For these reasons, in this paper, a new growth method of CIGS layer was attempted to hydride vapor transport (HVT) method. The CIGS mixed-source material reacted for HCl gas in the source zone was deposited on the substrate after transporting to growth zone. c-plane $Al_2O_3$ and undoped GaN were used as substrates for growth. The characteristics of grown samples were measured from SEM and EDS.

• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.681-686
• /
• 1994

Microwave Detector Using $YBa_{2}Cu_{3}O_{7-x}$, Grain Boundary Junction $YBa_{2}Cu_{3}O_{7-x}$ superconductor thin films were deposited on $LaAIO_{3}$ (100) single crystal substrates using a metal organic chemical vapor deposition (MOCVD) method. These films showed the critical temperature of about 9OK and critical current density of over $10^5/A \textrm{cm}^2$at 77K. These films showed granular structure with 0.5~1.5$\mu \textrm{m}$ grains. Bridge-type junctions, 6$\mu \textrm{m}$ in width and 6pm in length, were fabricated using the photolithography and the Ar ion milling techniques. Current-voltage (I-V) characteristics of these junctions with the microwave irradiation at 77K were studied. The critical current densities decreased as the irradiated microwave power increased. When microwaves were irradiated on the bridge at 77K. the I-V charateristics showed constant voltage stcp(Shapiro steps) at $\Delta$=nho/2e.

• Journal of the Korean Society of Safety
• /
• v.28 no.2
• /
• pp.37-41
• /
• 2013

In this work, we report the effect on the volatole organic compounds(VOCs) sensing properties of Copper phthalocyanine(CoPc) and Dilithium phthalocyanine(DiLiPc) thin films onto alumina substrates. Use evaporation method and the spin-coated method for sensing device. The materials of metallophthalocyanine macrocyclic compound solutions blended with N,N'-diphenyl-N,N'-bis(1-naphthyl)-1,1'-biphenyl-4,4"-diamine and/or Poly[2-methoxy-5-(2'-ethylhexyloxy)-1,4-phenylenevinylene] solutions. The influence of the blended in with metallophthalocyanine macrocyclic compounds on the resistance have been measured and analyzed in five different volatole organic compounds. The following results were obtained: The AFM 3D image of thin films deposited on metallophthalocyanine macrocyclic compound shows that the surfaces roughness were about CuPc 4.1~14.3 nm(7.5~8.1%), DiLiPc 10.3~22.2 nm(7.9~11.5%). The resistances decreases upon increasing the concentration of vapor organic compounds to CuPc and DiLiPc thin films. That thin films blended Copper phthalocyanine(CoPc) and Dilithium phthalocyanine(DiLiPc) with N,N'-diphenyl-N,N'-bis(1-naphthyl)-1,1'-biphenyl-4,4"-diamine and/or Poly[2-methoxy--5-(2'-ethylhexyloxy)-1,4-phenylenevinylene]. The resistances of blended thin films with N,N'-diphenyl-N,N'-bis(1-naphthyl)-1,1'-biphenyl-4,4"-diamine and/or Poly[2-methoxy--5-(2'-ethylhexyloxy)-1,4-phenylenevinylene] decreases upon increasing the concentration of volatole organic compounds(VOCs) on DiLiPc than CuPc compound thin films.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.98-102
• /
• 2005

This article describes a study of chemical vapor deposition (CVD) of copper thin films on TiN substrates using (HFAC)Cu(DMB) as a precursor. The surface morphology and conformality of the Cu films as functions of substrate temperature and the presence or absence of iodine have been investigated. The surface roughness was increased significantly along with decrement of the step coverage by increasing the deposition temperature. The highest conformal films with the lowest surface roughness were obtained using the process of copper CVD, where iodine vapor were discretely introduced into the reactor during the growth of copper.