• Clean Technology
• /
• v.23 no.2
• /
• pp.158-162
• /
• 2017

$FeCl_3$ solution has been used as an etchant for metal etching such as Fe, Cu, Al and Ni. In the etching process, $Fe^{3+}$ is reduced to $Fe^{2+}$ and the etching efficiency is decreased. Waste $FeCl_3$ etchant has environmental, economic problems and thus the regeneration of the etching solution has been required. In this study, HCl was mixed with the $FeCl_2$ solution and then, $H_2O_2$, $NaClO_3$ were added into the mixed solution to oxidize the $Fe^{2+}$. During the oxidation process, oxidation-reduction potential (ORP) was measured and the relationship between ORP and oxidation ratio was investigated. The ORP is increased with increasing the concentration of $H_2O_2$ and $NaClO_3$, and then the ORP is decreased with oxidation progress. Such a behavior was in good agreement with Nernst's equation. Also, the oxidation efficiency was about 99% when a sufficient amount of HCl and $H_2O_2$, $NaClO_3$ were added.

• Korean Chemical Engineering Research
• /
• v.46 no.4
• /
• pp.813-818
• /
• 2008

Various additives were added in small amounts on Ni/YSZ anode of SOFC (solid oxide fuel cell) in order to improve reactivity and to inhibit deactivation due to coke deposition during methane reforming using a low mole ratio steam ($H_2O/CH_4=1.5$) at $800^{\circ}C$. Ni/YSZ catalysts added with various perovskites did not show any improvement but exhibited a gradual decrease in the methane conversion. K-doped Ni/YSZ showed a steady increase and maintenance of the conversion up to 42 hours, after which there was an abrupt deactivation of catalyst owing to potassium loss by volatilization. Addition of 5% of $K_2Ti_2O_5$ on Ni/YSZ showed a stable maintenance of the conversion without K loss, and was able to prevent coke formation during a long time operation. Deactivation of catalyst during the reaction was mainly caused by the accumulation of graphidic carbon on the catalyst surface.

• Journal of Environmental Science International
• /
• v.2 no.1
• /
• pp.61-72
• /
• 1993

Result of this study indicate that two criteria must be met in order to have effective macrocycle-mediated transport in these emulsionsystem. First, one must effective extraction of the post transition metals, $Cd^{2+}$. $Pb^{2+}$ and $Hg^{2+}$ , into toluene membrane. The effectiveness of this extraction is greatest if log K values for the metal-macrocycle interaction is large. Second, the ratio of the log K values for the metal ion-receiving phase to the metal ion-macrocycle interaction must be large enough to ensure quantitative stripping of the metal ion at the toluene phase interface. Control of the first step can be obtained by appropriate selection of macrocycle donor atom, substituents, and cavity radius. The second step can be controlled by selecting the proper complexing agent for inclusion in the receiving phase. The order of the transport, when using the several $A^-$ species such as $SCN^-$, $1^-$, $Br^-$ and $Cl^-$ is the order of the changing degree of solvation for $A^-$ and the transport of the metals is also affected by the control of concentration for receiving species because of solubility-differences. In this study, we can seperate each single metal ion from the mixture of $Cd^{2+}$, $Pb^{2+}$, and $Hg^{2+}$ ions by using the toluene membranes controlled by optimized conditions. Transport of the single metal is also very good, and alkaline and alkaline earth metals as interferences ions did not affect the seperation of the metals in this macrocycle-liquid membrances but transition metal ions were partially affected as interferences for the post transition metal ions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.241-241
• /
• 2007

We fabricated SmBCO coated conductors(CCs) on IBAD-MgO templates using co-evaporation method. IBAD-MgO templates consist of PLD-LMO/epi-MgO/IBAD-MgO/Ni-alloy and showed good in-plane texture of below FWHM 7 degree. Evaporation rates of Sm, Ba, and Cu were precisely controlled to get the optimum composition ratio after deposition process. To optimize the oxygen partial pressure of reaction region, wide range of the partial pressure was investigated from 1 mTorr to 15 mTorr. By reducing the oxygen partial pressure to 5mTorr, (103)grains in SmBCO layer have been increased. On the other hand, there were only (001)grains in SmBCO layer deposited at 15 mTorr $O_2$. Deposition temperature was also investigated from $600^{\circ}C\;to\;800^{\circ}C$ to make high Ic SmBCO CCs. SmBCO on IBAD MgO template showed that the Ic increased gradually at higher growth temperature to $800^{\circ}C$, which the highest Jc and Ic is $2.6\;MA/cm^2$ and 500 A/cm-w., respectively.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.4
• /
• pp.155-163
• /
• 2019

Mixture electrodes of a graphite having a good cycle performance and a silicon monoxide (SiO) having a high capacity are fabricated and their cycle performances are evaluated as negative electrodes for lithium-ion batteries. The electrode prepared by mixing the natural graphite and carbon-coated SiO in a mass ratio of 9:1 shows a reversible capacity of $480mAh\;g^{-1}$, 33% higher than that of graphite. However, the capacity deteriorates continuously upon cycling due to the volume change of silicon monoxide. In this study, the factors that can improve the cycle performance have been discussed through the change in the configurations of the electrode and the electrolyte. The electrode using the carboxymethyl cellulose (CMC) binder shows the best cycle performance compared to the conventional binders. The electrode sing the CMC and styrene-butadiene rubber (SBR) binder not only has almost the similar cycle characteristics with the electrode using the CMC binder but also has the better rate capability. When the fluoroethylene carbonate (FEC) is used as an electrolyte additive, the cycle life is improved. However, the electrolyte with 5 wt% of FEC is appropriate because the rate capability decreases when the content of FEC is increased to 10 wt%. In addition, when the mass loading of the electrode is lowered, the cycle performance is greatly improved. Also, enhanced cycle performance is achieved using the roughened Cu current collector polished by abrasive paper.

• Korean Journal of Soil Science and Fertilizer
• /
• v.31 no.1
• /
• pp.39-45
• /
• 1998

As a basic research for developing a sludge application technique in forestry, this study was conducted to investigage a reasonable amount and period of sludge to be applied onto forest nursery of Acer palmatum Thunb. The paper mill sludge was used for the study, and ammonium nitrate was treated to some of them to reduce the C/N ratio lower than 40. The maximum amount of applied sludge was 7ton/ha/year, and they were spread on spring and on late summer. The sludge application did not stimulate early growth of the trees during a year. Since there was no significant changes in soil chemical properties, the amount of applied sludge was thought to be too little to result in a significant role for tree growth. However, the soil water showed significant increase of Cu when the activated sludges were applied during late summer. Thus, the time of application need to be determined cautiously with considering the risk of ground water contamination. In conclusion, if we set a goal from the view point of long-term concept such as forest productivity rather than to get a short-term product, the uncomposted sludge in small amount during growing season might be considered to be applied on forest nursery.

• Journal of Sericultural and Entomological Science
• /
• v.55 no.2
• /
• pp.33-39
• /
• 2019

Freeze-dried silkworm powder has been approved as a functional ingredients for blood glucose control since 2009. Proximate and nutrient compositions of silkworm powder was summerized as bellow. Silkworm powder contained 4.7% moisture, 57.7% crude protein, 9.5% crude fat, 5.4% crude fiber, and 9.3% ash. The larval protein contained 18 known amino acid including glutamic acid and aspartic acid. Fat is composed of 3:7 ratio of saturated fatty acid to unsaturated fatty acid including various essential fatty acids. It contained 34.7 linolenic acid, 24.4% oleic acid, 20.2% palmitic acid, 9.2% stearic acid, and 7.7% linoleic acid. Five minerals, K, P, Ca, Mg, S were abundant in the silkworm powder with other minerals such as Cu, Mn, Fe, and Zn.

• Clean Technology
• /
• v.28 no.4
• /
• pp.323-330
• /
• 2022

Microfluidic paper-based analytical devices (μPADs) have recently been in the spotlight for their applicability in point-of-care diagnostics and environmental material detection. This study presents a double-sided printing method for fabricating 3D-μPADs, providing simple and cost effective metal ion detection. The design of the 3D-μPAD was made into an acryl stamp by laser cutting and then coating it with a thin layer of PDMS using the spin-coating method. This fabricated stamp was used to form the 3D structure of the hydrophobic barrier through a double-sided contact printing method. The fabrication of the 3D hydrophobic barrier within a single sheet was optimized by controlling the spin-coating rate, reagent ratio and contacting time. The optimal conditions were found by analyzing the area change of the PDMS hydrophobic barrier and hydrophilic channel using ink with chromatography paper. Using the fabricated 3D-μPAD under optimized conditions, Ni²⁺, Cu²⁺, Hg²⁺, and pH were detected at different concentrations and displayed with color intensity in grayscale for quantitative analysis using ImageJ. This study demonstrated that a 3D-μPAD biosensor can be applied to detect metal ions without special analysis equipment. This 3D-μPAD provides a highly portable and rapid on-site monitoring platform for detecting multiple heavy metal ions with extremely high repeatability, which is useful for resource-limited areas and developing countries.

• Horticultural Science & Technology
• /
• v.34 no.5
• /
• pp.727-735
• /
• 2016

This research was conducted to investigate the influence of various pre-planting $NO_3:NH_4$ ratios in the coir dust+peatmoss+perlite (3.5:3.5:3, v/v/v) medium on the growth of tomato plug seedlings (cv. Dotaerang Dia), changes in chemical properties of root media, and tissue nutrient contents. With the fixation of N concentration to $300mg{\cdot}L^{-1}$, the $NO_3:NH_4$ ratios were adjusted to 100:0, 73:27, 50:50, 27:73, 0:100. Then, root media containing various $NO_3:NH_4$ ratios and equal concentration of other essential nutrients were filled into 50-cell plug trays and the seeds of 'Dotaerang Die' tomato were sown. The investigation of seedling growth and tissue analysis for mineral nutrient contents based on the dry weight of above-ground tissue were conducted 6 weeks after sowing. As seedlings grew, the EC decreased quickly and pH increased gradually in the all treatment media. The plant height, fresh weight and dry weight of seedlings in the treatment of 50:50 ($NO_3:NH_4$) were 29.0 cm, 13.7 g, and 1.21 g, respectively, which were the highest among treatments tested. However, the seedlings in the treatment of 0:100 ($NO_3:NH_4$) had 26.5 cm, 11.2 g, and 0.92 g in plant height, fresh weight and dry weight, respectively. These were the poorest among the treatments tested. The tissue contents of N were 2.77 to 3.22% in all the treatments. The treatment of 27:73 ($NO_3:NH_4$) had the highest contents of Fe, Mn and Zn and that of 0:100 ($NO_3:NH_4$) had the lowest contents of Mg, Na, Cu, Mn and Zn among the treatments tested. The results indicate that $NH_4$ ratio should be lower than 50% in the coir dust+peatmoss+perlite (3.5:3.5:3, v/v/v) medium for seedling growth of tomato and the optimum ratio will be used to draw up guide lines for plug seedling production.

• The Korean Journal of Mycology
• /
• v.41 no.1
• /
• pp.21-27
• /
• 2013

This study was carried out to investigated optimum mixing ratio of Korean natural Acer tegmentosum for production of functional oyster mushroom. Total nitrogen and carbon sources of Acer tegmentosum were 0.2% and 44.4%, respectively and C/N ratio was 234. Total nitrogen source and pH of substrate mixed with Acer tegmentosum were 2.7~2.9 and 4.8~5.0, respectively. The contents of $P_2O_5$, $K_2O$ and MgO at Acer tegmentosum media were higher than that of the control. Mycerial growth was the fastest at Acer tegmentosum 10%, and slower by increase of Acer tegmentosum substrate. Yields of fruiting body was the highest to 159 g/850 mL at 10% of Acer tegmentosum and dimeter and thick of pileus were the highest, too. The L value of pileus and stipes were decreased by increase of Acer tegmentosum substrate, but there was no significant difference in the a-value and the b-value. The contents of $P_2O_5$ and $K_2O$ of fruiting body were increased at Acer tegmentosum substrate, but there was no significant difference in contents of CaO, MgO and $Na_2O$.