• Ocean and Polar Research
• /
• 제28권3호
• /
• pp.215-224
• /
• 2006

Spatial variation of heavy metal accumulation was investigated in Manila clam Ruditapes philippinarum collected from several tidal flats. Sediment metal levels varied highly among the sites, which was attributed primarily to differences in Fe and organic carbon contents and in part to gain size. Significant differences in metal concentrations also were found in the clam tissue among the different sampling sites. However, except for a few metals (Mn, Zn, Pb), which showed some elevation, the variations in the clam tissue were not related to the variations in the sediment. This is likely because most metals in filter-feeding herbivores such as R. philippinarum accumulated as a result of feeding on suspended particles such as phytoplankton and organic detritus in the water column, not in bottom sediment. In addition, tissue weight for a specific shell size varied significantly among the sites, and increased tissue mass indicating a good nutritive condition likely caused a subsequent dilution of body metals leading to reduced weight-specific concentrations of some metals (Cd, Zn, Cu, Co).

• 한국분말재료학회지
• /
• 제24권2호
• /
• pp.102-107
• /
• 2017

Porous polytetrafluoroethylene (PTFE) thin films are fabricated by spin-coating using a dispersion solution containing PTFE powders, and their crystalline properties are investigated after thermal annealing at various temperatures ranging from 300 to $500^{\circ}C$. Before thermal annealing, the film is densely packed and consists of many granular particles 200-300 nm in diameter. However, after thermal annealing, the film contains many voids and fibrous grains on the surface. In addition, the film thickness decreases after thermal annealing owing to evaporation of the surfactant, binder, and solvent composing the PTFE dispersion solution. The film thickness is systematically controlled from 2 to $6.5{\mu}m$ by decreasing the spin speed from 1,500 to 500 rpm. A triboelectric nanogenerator is fabricated by spin-coating PTFE thin films onto polished Cu foils, where they act as an active layer to convert mechanical energy to electrical energy. A triboelectric nanogenerator consisting of a PTFE layer and Al metal foil pair shows typical output characteristics, exhibiting positive and negative peaks during applied strain and relief cycles due to charging and discharging of electrical charge carriers. Further, the voltage and current outputs increase with increasing strain cycle owing to accumulation of electrical charge carriers during charge-discharge.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 C
• /
• pp.543-546
• /
• 2000

본 논문에서는, 모의 진공차단기 내에서의 구리 증기입자의 공간적 및 시간적 밀도분포를 레이저유기형광법 (LIF)에 의해 계측하였다. 레이저 트리거 방전에 의해 생성된 어블레이션(ablation) 플라즈마에서의 구리입자를 324.75nm의 Nd:YAG 레이저를 이용하여 여기시키고, 이때 여기준위에서 기저준위로 천이할 때의 형광신호(510.55nm)를 분광기 및 광전자증배관을 이용하여 계측하였다. 음극점으로부터 넓은 각도를 가지고 전자가 튀어나오며, 넓은 범위에 걸쳐 전자나 이온이 존재하는 것을 알 수 있었다. 또한 음극으로부터 8mm ( x=0, y=8mm 진 위치에서 가장 강한 신호와, 2mm ( x=0, y=2mm 가장 약한 신호를 얻을 수 있었다.

• 한국환경보건학회지
• /
• 제19권1호
• /
• pp.30-36
• /
• 1993

A survey was conducted to measure concentration of airborne microbe in a hospital using RSC air sampler during October~November 1991.The result was as follows: 1) In an agar strip GK-A media for total counts of microbial particles. The highest count were 1384 CFU/m$^3$ in the main lobby, followed by 912 CFU/m$^3$, in the obstetric room, 688 CFU/m$^3$ in 1CU. By gram staining, the distribution for organisms in the air were shown 74.1% in gram possitive cocci followed by 16.8%, in gram possitive bacilli 6.7% in gram negative bacilli and 4.7% in yeast, but low organism was detected in recovery room with 194 CFU/m$^3$. 2) In agar strip S media for Staphylococci the count at the main lobby was detected in the recovery room with 92 CFU/m$^3$, Tests of coagulase were negative Staphylococci with 78%, and positive Staphylococci with 22%. The Staphylococci were highly resistance to penicillin, ampicillin and sensitive to amikacin, cefazolin, gentamycin and chloramphenicol. 3) In agar strip C media for coliform bacteria the colony counts at the main lobby was 139 CFU/m$^3$ and treatment room was 190 CFU/m$^3$, most frequently isolated microorganisms were non fermentative bacilli. 4) In agar strip HS media for yeast and molds. Most frequently colony counts 17~76 CFU/m$^3$, 0.5% lactophenol cotton blue stains were shown unidentified 77.2%, 8.1%, in Penicillium 8.1% in Aspergillus, and 3.8% in mucor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.1998-2000
• /
• 2005

The effects of the addition of nanocrystalline Y2O3 powder on the microstructure and superconducting properties have been investigated in YBCO films prepared by TFA-MOD process. Precursor solution doped with extra $Y_2O_3$ Powder was prepared by adding $Y_2O_3$ powder into a stoichiometic precursor solution with a cation ratio of Y:Ba:Cu=1:2:3. Coating solutions with and without $Y_2O_3$ doping were coated on $LaAlO_3(100)$ single crystal by a dip coating method, cacination and conversion heat treatments were performed at the controlled atmosphere containing water vapor Current carry capacity(Jc) of YBCO film was enhanced about 50% by $Y_2O_3$ doping. It is thought that the enhancement of Jc is due to the better connectivity of YBCO grains and/or the flux pinning by the presence of nanocrystalline $Y_2O_3$ Particles embedded in YBCO grains.

• 한국전기전자재료학회논문지
• /
• 제24권8호
• /
• pp.616-621
• /
• 2011

In this paper, CdS thin films, which were widely used window layer of the CdTe and the Cu(In,Ga)$Se_2$ thin film solar cell, were grown by chemical bath deposition, and effects of pH of reaction solution on the structural and optical properties were investigated. For pH<10.5, as the pH of reaction solution was higher, the deposition rate of CdS films was increased by improving ion-by-ion reaction in the substrate surface and the crystallinity of the films was improved. However, when the pH was higher than 10.5, the deposition rate was decreased because of smaller $Cd^{2+}$ ion concentration in the reaction solution. Also, the crystallinity of the films were deteriorated. The CdS films deposited at lower pH showed poor optical transmittance due to adsorbed colloidal particles, while the transmittance was improved for higher pH.

• 한국표면공학회지
• /
• 제49권3호
• /
• pp.265-273
• /
• 2016

The effects of surface modification by nitric acid on the pre-treatment of electroless copper plating were investigated. Copper was electroless-plated on the nitric acid treated graphite activated by a two-step pre-treatment process (sensitization + activation). The chemical state and relative quantities of the various surface species were determined by X-ray photoelectron spectroscopy (XPS) after nitric acid modification or pre-treatment. The acid treatment increased the surface roughness of the graphite due to deep and fine pores and introduced the oxygen-containing functional groups (-COOH and O-C=O) on the surface of graphite. In the pre-treatment step, the high roughness and many functional groups on the nitric acid treated graphite promoted the adsorption of Sn and Pd ions, leading to the uniform adsorption of catalyst ($Pd^0$) for Cu deposition. In the early stage of electroless plating, a lot of tiny copper particles were formed on the whole surface of acid treated graphite and then homogeneous copper film with low variation in thickness was formed after 30 min.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.43-44
• /
• 2015

Electrodeposited Ni and Ni-SiC composite coatings were prepared on Cu substrates by using the Ni-Sulfamate electrolytic bath. Thus prepared samples were subjected for the two different types of post surface modification techniques; i.e. Laser Surface Texturing (LST) and Ultrasonic Nano Surface Modification (UNSM), respectively in order to investigate their effects on surface and interface related properties of the coatings. Hemispherical dimples, with 80 to 200 um dimple spacing, were created and examined on the surfaces of the materials studied. The results revealed that micro-surface texturing with 150 um dimple spacing considerably improved the coefficient of friction. Dimple spacing accuracy and incorporated second phase ceramic particles both contributed significantly to reduction in coefficient of friction. On the other hand, application of UNSM considerably modified the surface topography, led to increase the Vickers microhardness, and reduced the wear and coefficient of friction as compared to non UNSM treated Ni and Ni-SiC samples.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2011년도 추계학술논문집 1부
• /
• pp.357-360
• /
• 2011

A new copper adenine MOF (Bio-MOF) was synthesized by hydrothermal procedure and explored for its low temperature $CO_2$ adsorption. In this adenine a DNA nucleotide was used as a ligand for Cu in DMF solution at $130^{\circ}C$. The synthesized Bio MOF was characterized by XRD, SEM, EDS, TG and BE Tresults. The material possesses high surface area (716.08 $m^2g^{-1}$) with mono dispersed particles of about 2.126 nm. The maximum $CO_2$ adsorption capacity is 5wt% at $50^{\circ}C$, which is regenerable at $100^{\circ}C$ which is very low when compared to other metal organic frame work studied. This study proves that the synthesized material is also be a choice materials for low temperature $CO_2$adsorption.

• 한국산업융합학회 논문집
• /
• 제24권3호
• /
• pp.289-294
• /
• 2021

Tungsten (W) is used as a facing material for nuclear fusion reactors, and it is used in conjunction with structural materials such as copper alloy (CuCrZr), graphite, or stainless steel. On the other hand, since tungsten is a material with a high melting point, a method that can be manufactured at a lower temperature is important. Therefore, in this study, tungsten, which is a facing material, was attempted to be manufactured using a pressure sintering method. Material properties of sintered tungsten materials were analyzed for each solvent using two types of solvents, acetone and polyethylene glycol. The sintered tungsten material using acetone as a solvent exhibited a hardness value of about 255 Hv, and when polyethylene glycol was used, a hardness value of about 200 Hv was shown. The flexural strength of the sintered tungsten material was 870 MPa and 307 MPa, respectively, when acetone and polyethylene glycol were used as solvents. The sintered tungsten material using acetone as a solvent caused densification between particles, which served as a factor of increasing the strength.