• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.481-486
• /
• 2020

To evaluate geochemical characteristics of surface sediments in Samcheok Port, the distribution characteristics of particle sizes, organic matters and heavy metals were investigated. The sediments showed a mixed property of sand, silt, and clay, however fine-grains dominated at the inner port and coarse-grains dominated at the outer port. The organic (COD, TOC, and IL) contamination of the sediment at the inner port were higher than that of the outer port, and the concentrations of total nitrogen and total phosphorus at the inner port was higher than those of the outer port. Also, heavy metals contamination of surface sediments at the inner port was higher than those of the outer port (except for As). From the results of high organic matter concentrations and C/N ratio at the inner port, it is considered that the contamination of organic matters was mainly derived from the land. The correlation analysis among the particle size, chemical composition, and heavy metals resulted in high correlation between silt-clay and heavy metals, and between organic matters and heavy metals. The sequential extraction results of heavy metals showed the sum of exchangeable, carbonate, and oxide fractions of Ni, Zn, Cu, Pb, Cd, and As were 14.8, 49.8, 39.1, 32.2, 51.8 and 26.6%, respectively.

• Korean Journal of Materials Research
• /
• v.11 no.5
• /
• pp.405-412
• /
• 2001

Corrosion tests were carried out in $360^{\circ}C$ water and $360^{\circ}C$ 70ppm LiOH solution to investigate the corrosion behavior of new zirconium alloys (Zr-0.4Nb-0.8Sn-xFeCrMn, Zr-0.2Nb-1.1Sn-xFeCrMn, Zr-1.0Nb-xFeCu). Microstructures of tested alloys were analyzed by optical microscope and TEM. The cross-sectional surface and crystalline structure of the oxide layer were analyzed by SEM and XRD. From the results of corrosion test, all the alloys showed higher corrosion rates in $360^{\circ}C$ 70ppm LiOH aqueous solution thats in $360^{\circ}C$ water. Especially, high Nb-containing alloy exhibited the acceleration of corrosion rate in LiOH solution. The low Nb- and Sn-added alloys showed better corrosion resistance than the Sn- free high Nb alloy. from the effect of final annealing on the corrosion, it was observed that the partially recrystallized alloys showed better corrosion resistance than fully recrystallized alloys. This would be related to the size and distribution of the second phase particles.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.397-405
• /
• 2012

In this study, performance evaluation of newly developed technology for the economical and safe removal of volatile organic compounds (VOCs) coming out from electronic devices washing operation and offensive odor induction materials was made. Metal oxidization catalyst has shown 50% of removal efficiency at the temperature of $220^{\circ}C$. Composite metal oxidization catalyst applied in this study has shown that the actual catalysis has started at the temperature of $100^{\circ}C$. Comprehensive analysis on the catalyst property using Mn-Cu metal oxidization catalyst in the pilot-scale unit was made and the removal efficiency was variable with temperature and space velocity. Full-scale unit developed based on the pilot-scale unit operation has shown 95% of removal efficiency at the temperature of $160^{\circ}C$. Optimum elimination effective rates for the space velocity was found to be $6,000hr^{-1}$. The most appropriate processing treatment range for the inflow concentration of VOCs was between 200 ppm to 4,000 ppm. Catalyst control temperature showed high destruction efficiency at $150{\sim}200^{\circ}C$ degrees Celsius in 90~99%. External heat source was not necessary due to the self-heat reaction incase of VOCs inflow concentration is more than 1,000 ppm. Equipment and fuel costs compared to the conventional RTO/RCO method can be reduced by 50% and 75% respectively. And it was checked when there was poisoning for sulfide and acid gas.

• Journal of the Korean Chemical Society
• /
• v.53 no.3
• /
• pp.368-376
• /
• 2009

In this study we investigated and tried to understand problems monitored in an experiment on reactivity of metals in chemistry I. Three problems were discussed. First, the reason that aluminium plate does not react with other metal ions such as zinc, iron and copper was studied and the way to overcome this problem was suggested. Second, the reason that the bubbles were generated when FeS$O_4$(aq) and Zn(s) react was discussed. Third, the precipitates which appeared in the reaction of FeS$O_4$(aq) and Zn(s) were identified. Through reference study and experimental investigation, we could reach the following results. First, aluminium could not react with other metal ions due to the surface oxide layer that is formed very fast and prevents aluminium from reacting with metal ions in solution. This problem could be overcome by allowing a competing reaction of acid and aluminium during the reaction of aluminium and metal ions. Second, the observed bubbles were identified to be hydrogen gas, produced by the reaction between metals and hydronium ion in the solution. Third, black precipitates that were produced on the surface of zinc plate and exhibited magnetic property were characterized to be $Fe_3O_4$(s), and brown precipitates that were produced in the solution phase were to be $Fe_2O_3$(s) by the analysis of X-ray photoelectron spectra.

• The Korean Journal of Physiology and Pharmacology
• /
• v.4 no.1
• /
• pp.33-40
• /
• 2000

This study was designed to clarify the mechanism of the inhibitory action of a nitric oxide (NO) donor, 3-morpholino-sydnonimine (SIN-1), on contraction, cytosolic $Ca^{2+}$ level $([Ca^{2+}]_i)$ and ionic currents in guinea-pig ileum. SIN-1 $(0.01{\sim}100\;{\mu}M)$ inhibited 25 mM KCl- or histamine $(10\;{\mu}M)-induced$ contraction in a concentration-dependent manner. SIN-1 reduced both the 25 mM KCl- and the histamine-stimulated increases in muscle tension in parallel with decreased $[Ca^{2+}]_i.$ Using the patch clamp technique with a holding potential of -60 mV, SIN-1 $(10\;{\mu}M)$ decreased peak Ba currents $(I_{Ba})$ by $30.9{\pm}5.4%$ (n=6) when voltage was stepped from -60 mV to +10 mV and this effect was blocked by ODQ $(1\;{\mu}M),$ a soluble guanylyl cyclase inhibitor. Cu/Zn SOD (100 U/ml), the free radical scavenger, had little effect on basal $I_{Ba},$ and SIN-1 $(10\;{\mu}M)$ inhibited peak $I_{Ba}$ by $32.4{\pm}5.8%$ (n=5) in the presence of Cu/Zn SOD. In a cell clamped at a holding-potential of -40 mV, application of $10\;{\mu}M$ histamine induced an inward current. The histamine-induced inward current was markedly and reversibly inhibited by $10\;{\mu}M$ SIN-1, and this effect was abolished by ODQ $(1\;{\mu}M).$ In addition, SIN-1 markedly increased the depolarization-activated outward $K^+$ currents in the all potential ranges. We concluded that SIN-1 inhibits smooth muscle contraction mainly by decreasing $[Ca^{2+}]_i$ resulted from the inhibition of L-type $Ca^{2+}$ channels and the inhibition of nonselective cation currents and/or by the activation of $K^+$ currents via a cGMP-dependent pathway.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.5
• /
• pp.218-227
• /
• 2021

A thick film NTC thermistor for low temperature co-firing was manufactured by printing and sintering a paste prepared using NTC powder of Mn_1.5Ni_0.4Co_0.9Cu_0.4O₄ composition, lead free frit, and RuO₂ on a 96 % alumina substrate. The effect of frit and RuO₂ on the electrical properties of thick film NTC thermistor was studied. The resistance of the thick film NTC thermistor was higher than that of the bulk phase sintered at the same temperature, but it was found that the negative resistance temperature characteristic appeared more clearly and linearly in the resistance - temperature characteristic. On the other hand, the area resistance decreased as the sintering temperature increased, and the area resistance increased as the amount of frit added increased. The B constant of the thick film NTC thermistor was 3000 K or higher. Among them, it was found that the B constant of the thick film NTC thermistor made of paste with 5 wt% of frit added and sintered at 900℃ showed the highest B constant. Also, it can be seen that the area resistance decreased with the addition of RuO₂, and the change in the area resistance decrease of the thick film NTC thermistor obtained by sintering the paste containing 5 wt% of RuO₂ at 900℃ is the most obvious.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.2
• /
• pp.1-8
• /
• 2019

The demand and importance of adhesives and paint coatings applied to solid surfaces such as metals, ceramics, and plastics are increasing. In this study, the influencing factors on the adhesive strength between the polymer coating and the metal adherend were investigated by Dolly test when the adhesive or the paint coating was applied on the metal adherend. Two-component epoxy adhesive was used as the adhesive, and EH2350, a two-component epoxy paint for anti-corrosion, was used as the paint. Especially, the effect of adherend metals(Al, Fe, STS, Cu, Zn), surface roughness and surface contamination(tap water, salt water) on adhesive strength was studied as influencing factors. The adhesive strength between adhesive and adherend was different when the type of metal adherend was different even when the same adhesive was used. It was found that spray water cleaning was necessary before the paint coating process on the surface of the oxide contaminated adherend with tap water or salt water. As a result of this study, it was confirmed that Dolly test can be widely used in the future to measure adhesive strength between paint coating and adherend.

• Economic and Environmental Geology
• /
• v.56 no.6
• /
• pp.745-764
• /
• 2023

In the Republic of Congo, Banded iron formations (BIFs) occur in two areas: the Chaillu Massif and the Ivindo Basement Complex, which are segments of the Archean Congo craton outcropping in the northwestern and southwestern parts of the country. They show interesting potential with significant mineral resources reaching 2 Bt and grades up to 60% Fe. BIFs consist mostly of oxide-rich facies (hematite/magnetite), but carbonate-rich facies are also highlighted. They are found across the country within the similar geological sequences composed of amphibolites, gneisses and greenschists. The Post-Archean Australian Shale (PAAS)-normalized patterns of BIFs show enrichment in elements such as SiO₂, Fe₂O₃, CaO, P₂O₅, Cr, Cu, Zn, Nb, Hf, U and depletion in TiO₂, Al₂O₃, MgO, Na₂O, K₂O, Sc, Th, Ba, Zr, Rb, Ni, V. REE diagrams show slight light REEs (rare earth elements; LREEs) compared to heavy REEs (HREEs), and positive La and Eu anomalies. The lithological associations, as well as the very high (Eu/Eu^*)_SN ratios> 1.8 shown by the BIFs, suggest that they are related to Algoma-type BIFs. The positive correlations between Zr and TiO₂, Al₂O₃, Hf suggest that the contamination comes mainly from felsic rocks, while the absence of correlations between MgO and Cr, Ni argues for negligeable contributions from mafic sources. Pr/Pr^* vs. Ce/Ce^* diagram indicates that the Congolese BIFs were formed in basins with redox heterogeneity, which varies from suboxic to anoxic and from oxic to anoxic conditions. They were formed through hydrothermal vents in the seawater, with relatively low proportions of detrital inputs derived from igneous sources through continental weathering. Some Congolese BIFs show high contents in Cr, Ni and Cu, which suggest that iron (Fe) and silicon (Si) have been leached through hydrothermal processes associated with submarine volcanism. We discussed their tectonic setting and depositional environment and proposed that they were deposited in extensional back-arc basins, which also recorded hydrothermal vent fluids.

• Korean Journal of Microbiology
• /
• v.20 no.3
• /
• pp.125-133
• /
• 1982

Mutational experiments were performed to imporve the cellulase productivity of Aspergillus phoenicis KU175, isolated from the southern part of Korea, as a high cellulase producer. By treatment ultra-violet light nad 4-NQO(4-Nitroquinoline-N-Oxide), mutation waas induced, and treatment ultra-violet light and 4-NQO (4-Nitroquinoline-N-Oxide), mutation was induced, and A.phoenicis KU175-115 was finally selected for its highest avicelase production. Avicelase production of the mutant was increased about 2 times compared with those of the wild strain. However, activities of other hydrolytic enzymes, such as amylase, protease and nuclease, of the mutant strain didn't show a marked difference compared with those of the nuclease, of the mutant strain didn't show a marked difference compared with the wild strain, except slight increase in ribonuclease activity and slight decrease in glucoamylase activity. Avicelases from the mutant strain selected were purified from wheat bran culture by successive salting out, followed by dialysis and column chromatography, and their charcteristics were compared with thosw of the wild strain. Avicelase was separated into three peaks in the mutant strain as well as in the case of wild strain. Avicelase II activity of the mutant strain was prominently higher than that of the wild strain, while avicelase I and III activities of those were equivalent. The optimal pH ranges and stability of avicelase II from the mutant strain were pH4-5 and pH3.5-6.0, respectively, as well as in the case of the wild strain. The optimal temperature and thermal stability of avicelase II from the mutant strain were $40{\sim}50^{\circ}C\;and\;20{\sim}55^{\circ}C$, respectively. These results were same as those of the wild strain. By the using of Eadie-Hofastee plot, $K_m\;and\;V_{max}$ of avicelase II from the mutant and the wild strain were calculated to be 2.29mg/ml and $4.84{\mu}g$ reducing sugar as glucose per min equally, from the line fitted to the data by the least square method. Activity of avicelase II from the mutant strain was slightly activated by $Mg^{++}\;but\;inhibited\;by\;Cu^{++}, \;Mn^{++}\;and\;Zn^{++}$, as well as in the case of the wild strain. Therefore, it was concluded that the mutant didn't induce the formation of another avicelase isozyme, or the changes in the properties of avicelase, but induce the changes in the productively of the same avicelase II by the action of regulatory gane.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.11a
• /
• pp.7-7
• /
• 2001

The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.