• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1139-1145
• /
• 1998

In this paper, to fabricate a superconducting fault current limiter(FCL) of thick film type, $YBa_2Cu_3O_X superconducting thick films were fabricated by surface diffusion process using the screen printing method. Powder mixture of $3BaCuO_2$+2CuO was screen printed on $Y_2BaCuO_5$(d=15mm). And critical current densities of the thick films were observed as the sintering temperature(92$0^{\circ}C$~95$0^{\circ}C$) and holding time(2h~10h). Based on experimental data, the thick films for superconducting FCL were sintered at $940^{\circ}C$ in 2 hours. The superconducting FCL with a current limiting area of 1mm wide and 66mm long was prepared on $Y_2BaCuO_5$ substrate. To measure the characterization of the fabricated FCL, an alternating voltage (60Hz) was applied to the FCL in 77K liquid nitrogen. At an applied voltage of 4V, the FCL was limited from 20A into 0.6A not farther than 0.5ms.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.123-124
• /
• 2005

We investigated the effect of a Ta/TaN Cu diffusion barrier existence on the reliability and the electrical performance of Cu dual-damascene interconnects. A high EM performance in Cu dual-damascene structure was observed the BCV(barrier contact via) interconnect structure to remain Ta/TaN barrier layer. Via resistance was decreased DCV interconnect structure by bottomless process. This structure considers that DCV interconnect structure has lower activation energy and higher current density than BCV interconnect structure. The EM failures by BCV via structure were formed at via hole, but DCV via structure was formed EM fail at the D2 line. In order to improve the EM characteristic of DCV interconnect structure by bottomless process, after Ta/TaN diffusion barrier layer in via bottom is removed by Ar+ resputtering process, it is desirable that Ta thickness is thickly made by Ta flash process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.05a
• /
• pp.22-27
• /
• 1993

we prepared 70K new BiPbAgSrCaCuO superconductor used diffusion of dual layer which composed of SrCaCuO and BiPbAgCuO compound. This method is used permeation and diffusion on partial melting point of BiPbAgCuO compound. Samples were analyzed by means of X-ray diffraction analysis, Thermal analysis, critical temperature and scanning electron microscopy. It was found that the best results were obtained for spread volume (A:B=1:0.6) and sintring time 210hours.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.214.2-214.2
• /
• 2013

Device performance for the 45 and 32 nm node CMOS technology requires the integration of ultralow-k materials. To lower the dielectric constant for PECVD and spin-on materials, partial replacement of the solid network with air (k=1.01) appears to be more intuitive and direct option. This can be achieved introducting of second "labile" phase during depositoin that is removed during a subsequent UV curing and annealing step. Besides, with shrinking line dimensions the resistivity of barrier films cannot meet the International Technology Roadmap for Semiconductors (ITRS) requirements. To solve this issue self-forming diffusion barriers have drawn attention for great potential technique in meeting all ITRS requirments. In this present work, we report a Cu-V alloy as a materials for the self-forming barrier process. And we investigated diffusion barrier properties of self-formed layer on low-k dielectrics with or without UV curing treatment. Cu alloy films were directly deposited onto low-k dielectrics by co-sputtering, followed by annealing at various temperatures. X-ray diffraction revealed Cu (111), Cu (200) and Cu (220) peaks for both of Cu alloys. The self-formed layers were investigated by transmission electron microscopy. In order to compare barrier properties between V-based interlayer on low-k dielectric with UV curing and interlayer on low-k dielectric without UV curing, thermal stability was measured with various heat treatment temperature. X-ray photoelectron spectroscopy analysis showed that chemical compositions of self-formed layer. The compositions of the V based self-formed barriers after annealing were strongly dominated by the O concentration in the dielectric layers.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.1-10
• /
• 2023

Recently, as the demand for high-performance computers and mobile products increases, semiconductor packages are becoming high-integration and high-density. Therefore, in order to transmit a large amount of data at once, micro bumps such as flip-chip and Cu pillar that can reduce bump size and pitch and increase I/O density are used. However, when the size of the bumps is smaller than 70 ㎛, the brittleness increases and electrical properties decrease due to the rapid increase of the IMC volume fraction in the solder joint, which deteriorates the reliability of the solder joint. Therefore, in order to improve these issues, a layer that serves to prevent diffusion is inserted between the UBM (Under Bump Metallization) or pillar and the solder cap. In this review paper, various studies to improve bonding properties by suppressing excessive IMC growth of micro-bumps through additional layer insertion were compared and analyzed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.409-409
• /
• 2013

최근, 집적 소자의 미세화에 따라 늘어난 배선 신호 지연 및 상호 간섭, 그리고 소비 전력의 증가는 초고집적 소자 성능 개선에 한계를 가져온다. 이에 따라 기존의 알루미늄(Al)/실리콘 절연 산화막은 구리(Cu)/저유전율 박막(low-k)으로 대체되고 있고, 이는 소자 성능 개선에 큰 영향을 미친다. 그러나 Cu는 Si과 low-k 내부로 확산이 빠르게 일어나 소자의 비저항을 높이고, 누설 전류를 일으키는 등 소자의 성능을 저하시킬 수 있는 문제점을 가지고 있다. 이러한 Cu의 확산을 막기 위하여 Ta, TaN 등과 같은 확산방지막에 대한 연구가 활발히 진행되어 왔으나, 배선 공정의 집적화와 low-k 대체에 따른 공정 및 신뢰성 문제로 인해 새로운 확산방지막의 개발이 필요하게 되었다. 이를 위해, 본 연구에서는 Cu-V 합금을 사용하여 low-k 기판 위에 확산방지막을 자가 형성 시키는 공정에 대한 연구를 진행하였다. 다양한 low-k 기판에서 열처리조건에 따른 Cu-V 합금의 특성을 확인하기 위해 4-point probe를 통한 비저항 평가와 XRD (X-ray diffraction) 분석이 이뤄졌다. 또한, TEM (transmission electron microscope)을 이용하여 $300^{\circ}C$에서 1 시간 동안 열처리를 거쳐 자가형성된 V-based interlayer가 low-k와 Cu의 계면에서 균일하게 형성된 것을 확인하였다. 형성된 V-based interlayer의 barrier 특성을 평가하고자 Cu-V합금/low-k/Si 구조와 Cu/low-k/Si 구조의 leakage current를 비교 분석하였다. Cu/low-k/Si 구조는 비교적 낮은 온도에서 leakage current가 급격히 증가하는 양상을 보였으나, Cu-V 합금/low-k/Si 구조는 $550^{\circ}C$의 thermal stress 에서도 leakage current의 변화가 거의 없었다. 이러한 결과를 바탕으로 열처리를 통해 자가형성된 V-based interlayer의 Cu/low-k 간 확산방지막으로서 가능성을 검증하였다.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.503-508
• /
• 1999

We have investigated the physical and diffusion barrier property of Ti-Si-N film for Cu metallization. The ternary compound was deposited by using reactive rf magnetron sputtering of a TiSi$_2$target in an Ar/$N_2$gas mixture. Resistivities of the films were in range of 358$\mu$$\Omega$-cm, to 307941$\mu$$\Omega$-cm, and tended to increase with increasing the $N_2$/Ar flow rate ratio. The crystallization of the Ti-Si-N compound started to occur at 100$0^{\circ}C$ with the phases of TiN and Si$_3$N$_4$identified by using XRD(X-ray Diffractometer). The degree of the crystallization was influenced by the $N_2$/Ar flow ratio. The diffusion barrier property of Ti-Si-N film for Cu metallization was determined by AES, XRD and etch pit by secco etching, revealing the failure temperature of 90$0^{\circ}C$ in 43~45at% of nitrogen content. In addition, the very thin compound (10nm) with 43~45at% nitrogen content remained stable up to $700^{\circ}C$. Furthermore, thermal treatment in vacuum at $600^{\circ}C$ improved the barrier property of the Ti-Si-N film deposited at the $N_2$(Ar+$N_2$) ratio of 0.05. The addition of Ti interlayer between Ti-Si-N films caused the drastic decrease of the resistivity with slight degradation of diffusion barrier properties of the compound.

• Korean Journal of Materials Research
• /
• v.27 no.7
• /
• pp.386-391
• /
• 2017

Using a customized diffusion bonder, we executed diffusion bonding for ring shaped white gold and red gold samples (inner, outer diameter, and thickness were 15.7, 18.7, and 3.0 mm, respectively) at a temperature of $780^{\circ}C$ and applied pressure of 2300 N in a vacuum of $5{\times}10^{-2}$ torr for 180 seconds. Optical microscopy, field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to investigate the microstructure and compositional changes. The mechanical properties were confirmed by Vickers hardness and shear strength tests. Optical microscopy and FE-SEM confirmed the uniform bonding interface, which was without defects such as micro pores. EDS mapping analysis confirmed that each gold alloy was 14K with the intended composition; Ni and Cu was included as coloring metals in the white and red gold alloys, respectively. The effective diffusion coefficient was estimated based on EDS line scanning. Individual values of Ni and Cu were $5.0{\times}10^{-8}cm^2/s$ and $8.9{\times}10^{-8}cm^2/s$, respectively. These values were as large as those of the melting points due to the accelerated diffusion in this customized diffusion bonder. Vickers hardness results showed that the hardness values of white gold and red gold were 127.83 and 103.04, respectively, due to solid solution strengthening. In addition, the value at the interface indicated no formation of intermetallic compound around the bonding interface. From the shear strength test, the sample was found not to be destroyed at up to 100,000 gf due to the high bonding strength. Therefore, these results confirm the successful diffusion bonding of 14K white-red golds with a diffusion bonder at a low temperature of $780^{\circ}C$ and a short processing time of 180 seconds.

• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.234-240
• /
• 2001

The diffusion barrier properties of TiN by using Cu(Mg) alloy film have been investigated. Cu(Mg) alloy film was deposited on air-exposed TiN film. Upon annealing, interfacial MgO of 100 $\AA$ has been formed due to the reaction of Mg with oxygen existed on the surface of TiN. Combined MgO/TiN structure prevented the interdiffusion of Cu and Si up to $800^{\circ}C$. To improve the adhesion of Cu(Mg) alloy film to the TiN, TiN layer was treated by $O_2$ plasma, followed by vacuum annealing at $300^{\circ}C$. It was found that increased oxygen on the surface of TiN film by plasma treatment enhanced segregation of Mg toward the interface, resulting in the formation of dense MgO layer. Improved adhesion characteristics have been formed through this treatment. However, increased power of $O_2$ plasma led to the formation of TiO$_2$ and decreased the Mg content to be segregated to the interface, resulting in the decrease in adhesion property. In addition, the deposition of 50 ${\AA}$ Si on the TiN enhanced the adhesion of Cu(Mg) alloy to TiN without deteriorating the TiN diffusion barrier characteristics.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.3
• /
• pp.7-12
• /
• 2018

The effects of Ru deposition temperature and post-annealing conditions on the interfacial adhesion energies of atomic layer deposited (ALD) Ru diffusion barrier layer and Cu thin films for the advanced Cu interconnects applications were systematically investigated. The initial interfacial adhesion energies were 8.55, 9.37, $8.96J/m^2$ for the sample deposited at 225, 270, and $310^{\circ}C$, respectively, which are closely related to the similar microstructures and resistivities of Ru films for ALD Ru deposition temperature variations. And the interfacial adhesion energies showed the relatively stable high values over $7.59J/m^2$ until 250h during post-annealing at $200^{\circ}C$, while dramatically decreased to $1.40J/m^2$ after 500 h. The X-ray photoelectron spectroscopy Cu 2p peak separation analysis showed that there exists good correlation between the interfacial adhesion energy and the interfacial CuO formation. Therefore, ALD Ru seems to be a promising diffusion barrier candidate with reliable interfacial reliability for advanced Cu interconnects.