• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.45-54
• /
• 1996

The effect of graphite on the frictional characteristics of Cu-based sintered friction materials was studied by pin-on-disk type wear test. A study has been carried out concerning the optimum concentration of graphite in sintered friction material to obtain the minimum wear rate and low friction coefficient . Friction coefficient and wear rate were increased as increasing the content of graphite in the matrix. In the study the optimum concentration of graphite was 19vol % to get the minimum wear rate and optimal frick'ion coefficient.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.55-58
• /
• 1995

The effects of Ni contents in Cu base sintered friction material were studied. The contents of Ni were increased up to 9 wt% in the Cu-Sn matrix. The microstincture and tribological behavior of the friction material were examined. Pin on disk type of constant speed friction test rig were used to measure the friction and the wear rates. The results show that Ni addition increased the friction coefficients and decreased the wear rates of the materials. Relations between microhardness of the matrix and friction properties have been discussed. In addition optimum Ni content is recommended through the analysis of wear debris.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1994년도 추계학술대회강연 및 발표대회 강연및 발표논문 초록집
• /
• pp.12-13
• /
• 1994

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1995년도 추계학술강연 및 발표대회 강연 및 발표논문 초록집
• /
• pp.15-15
• /
• 1995

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제23회 춘계학술대회
• /
• pp.99-107
• /
• 1996

Examined in this paper is the effect of B$_{4}$C addition on the frictional characteristics of Cu-Sn based sintered friction material. For the specimens 1%, 2% and 4% of B$_{4}$C were added into the reference material. A pin-on-disk type friction tester was used to measure the friction and wear with respect to the surface temperature and sliding distance. Wear mechanism of each specimen is analyzed in the view point of the oxide film formation. The specimen containing 4% of B$_{4}$C showed stable friction and low wear since the oxide film was sustained up to higher surface temperature ranges.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.373-378
• /
• 2013

엔진의 출력증대와 이에 따른 변속기의 크기 증가 등으로 인한 회전체의 관성증가로 변속기의 변속성능은 악조건이 되고 있다. 따라서, 이를 해결하기 위하여 내마모성이 높은 마찰소재의 개발이 요구된다. 디젤차량 수동변속기용 싱크로나이저 링에 요구되는 마찰특성에 적합한 소재를 개발하고, 이에 대한 접합 특성을 평가하였다. 즉, 철합금 모재와 동합금계 마찰재를 접합하는 공정을 개발하고, 접합층에 대하여 BSE분석, EDX분석을 수행하여 접합특성을 평가하였으며, 해당 시험편에 대하여 전단강도를 평가하였다.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.48-54
• /
• 1996

Examined in this paper, is the effect of B$_{4}$C addition on the frictional characteristics of Cu-Sn based sintered friction materials. For the specimens 1wt%, 2wt% and 4wt% of B$_{4}$C were added into the reference material. A pin-on-disk type friction tester was used to,measure the friction torque with respect to the surface temperature and sliding distance. Wear mechanism of each specimen is analyzed in the view point of the oxide film formation. The specimen containing 4wt% of B$_{4}$C showed stable friction and low wear since the oxide film was sustained up to higher surface temperature ranges.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.853-854
• /
• 2006

Warm compaction powder metallurgy was used to produce a $Ti_3SiC_2$ particulate reinforced Cu matrix composite. Fabrication parameters and warm compaction behaviors of Cu powder were studied. Based on the optimized fabrication parameters a Cu-based electrical contact material was prepared. Results showed that in expend of some electrical conductivity, addition of $Ti_3SiC_2$ particulate increased the hardness, wear resistivity and anti-friction ability of the sintered Cu-base material.