• Korean Journal of Materials Research
• /
• v.11 no.2
• /
• pp.115-119
• /
• 2001

The electrical properties of heavily drawn bundled Cu- Nb filamentary microcomposite wires were examined and correlated with the microstructural changes caused by thermomechanical treatments. The cross sectional shape of Nb filaments in wires fabricated by bundling and drawing appear straight or slightly curved. The different shape of Nb filaments is attributed to the break- up and cylinderization of Nb filaments during the bundling process at high temperatures. The resistivity of Cu-Nb microcomposites is predominantly controlled by electron scattering at Cu-Nb interfaces. The decrease of the conductivity below the annealing temperature of $400^{\circ}C$ is due to the increasing contribution of the scattering associated with coherency strains of needle- shaped precipitates. The slight decrease of the resistivity ratio (${\rho}_{295K}/{\rho}_{75K}$) is also due to the precipitation of Nb atoms. The increase in conductivity in Cu-Nb microcomposites at an annealing temperature of 50$0^{\circ}C$ is due to the coarsening and spheroidization of Nb filaments.

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.645-650
• /
• 1997

We manufactured CoNbZr/Cu/CoNbZr multi-layer films by rf magnetron sputtering methods and formed the patterns on the deposited multi-layer films. In this study, we fabricated a new etchant for forming the patterns by the wet etching with etchant and we searched for the best etching conditions and the etchant composition. Cu was etched selectively independent on the concentration of iron chloride solution, but amorphous CoNbZr thin film did not. The etchant was achieved by iron chloride solution(17.5 mol%) mixed with HF (20 mol%) during 150 sec, which etched CoNbZr/Cu/CoNbZr multi-layer films at the same time. Also, the etchant etched CoNbZr/Cu/CoNbZr multi-layer films by the three-step. It was shown that the cross-section had the isotropic structure and excellent etching characteristics with the above etchant.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.312-318
• /
• 2001

The mechanical and electrical properties of Cu-Nb filamentary nanocomposite fabricated by the bundling and drawing process were examined. The strength increased gradually with increasing Nb content while the ductility was insensitive to Nb content. The ratio of yield stresses at 293K and 75K are found to be 치ose to that of Young's moduli in various Cu-Nb nanocomposites, suggesting that athermal obstacles primarily control the strength. The fracture morphologies show ductile fractures irrespective of Nb contents. Secondary cracking along the interfaces between subelemental wires was occasionally observed and the frequency of secondary cracking increased with increasing Nb content. The conductivity and the resistivity ratio decreased with increasing Nb content. The decrease of the conductivity and the resistivity ratio(${\rho}_{293k}$/$\{rho}_{75k}$) can be explained by the increasing contribution of interface scattering.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.141-145
• /
• 1997

스퍼터링법으로 제조한 CoNbZr/Cu/CoNbZr 다층막에 대해 습식 식각법으로 패턴을 형성하기 위해 새로운 식각 용액을 제조하여 이 용액의 최적의 식각 조건에 대해 연구하였다. 염기성 수용액은 농도에 관계없이 Cu만을 선택적으로 식각하며 CoNbZr 비정질 박막은 식각하지 않았다. 그러나, 본 연구에서 제조 한 17.5 mol%의 염기성 수용액에 HF를 20 mol% 혼합한 식각 용액으로 CoNbZr/Cu/CoNbZr 다층막을 동시에 식각할 수 있었다. 또한 이 식각 용액은 CoNbZr/Cu/CoNbZr 다층막을 3단계로 식각하고 식각된 단면은 이방성 구조를 가지며, 매우 우수한 식각 특성을 나타내었다.

• Progress in Superconductivity and Cryogenics
• /
• v.24 no.3
• /
• pp.30-34
• /
• 2022

Effects of electron beam (EB) irradiation on the mechanical strength of Cu (conducting sheath) and Nb (diffusion barrier) of Cu/Nb/MgB₂ superconducting was investigated. Wire- and tape-type Cu/Nb/MgB₂ samples were irradiated at E-beam energy of 2.5 MeV and 5 mA and a maximum E-beam dose was 5×10¹⁷ e/m². The hardness value of Cu and Nb region was measured by the Vickers micro-hardness method. In the case of the wire sample, the hardness of Cu and Nb increased proportionally as the dose was increased up to 5×10¹⁷ e/m², whereas in the case of the tape sample, the hardness increased up to a dose of 0.5×10¹⁷ e/m², and decreased slightly 5×10¹⁷ e/m². The hardness increase of Cu and Nb is believed to be due to the decrease of the deformability of Cu and Nb due to the defects formed inside the materials by E-beam irradiation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.5
• /
• pp.210-215
• /
• 2006

Mechanical alloying (MA) by high energy ball mill of pure copper and niobium powders was carried out under the Ar gas atmosphere. The supersaturated solid solution can be produced in the range up to $Cu_xNb_{100-x}$(x=5-30) by MA for 120 hrs, as demonstrated by X-ray diffraction, DSC analysis and the electronic studies through a change in the superconducting transition in the low-temperature specific heat. The $Cu_{30}Nb_{70}$ samples ball-milled for 120 hrs exhibit only a broad exothermic heat release. The total energy, ${\Delta}H_t$ accumulated during MA far the mixture of $Cu_{30}Nb_{70}$ powders increased with milling time and approached the saturation value of 7.5 kJ/mol after 120 h of milling. It can be seen that the free energy difference between the supersaturated solid solution and the mixture of $Cu_{30}Nb_{70}$ powders is estimated to be 7 kJ/mol by Miedema et al. Hence it is thermodynamically possible to assume the formation of a supersaturated solid solution phase in this system.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.7
• /
• pp.347-351
• /
• 2004

The $ZnNb_2O_{6}$ ceramics with CuO(1, 3, 5wt%) were prepared by the conventional mixed oxide method. The ceramics were sintered at the temperature of $950^{\circ}C$∼$1075^{\circ}C$ for 3hr in air The structural properties and the microwave dielectric properties of $ZnNb_2O_{6}$ ceramics were investigated with sintering temperature and the addition of CuO. Increasing the addition of CuO, the peak of second phase($Cu_3Nb_2O_{8}$) was increased. The grain size of the $ZnNb_2O_{6}$ ceramics with CuO was increased with CuO addition at same temperature. The dielectric constant of $ZnNb_2O_{6}$ ceramics with CuO was increased with sintering temperature and CuO addition. While the quality factor of the $ZnNb_2O_{6}$ ceramics with lwt% CuO depended on sinterability, the quality factor of $ZnNb_2O_{6}$ with 3wt% and 5wt% CuO depended on second Phase due to the CuO addition. The optimum dielectric Properties of $\varepsilon$$_{r}$ = 21.73 Q${\times}$f = 19,276 were obtained from the condition of 3wt% CuO addition and sintering temperature of $1025^{\circ}C$(3hr).

• Electrical & Electronic Materials
• /
• v.8 no.4
• /
• pp.478-486
• /
• 1995

Cu/NbTi multilayer thin films and superconducting wires were fabricated and heat treated with conventional annealing and analyzed by differential scanning calorimetry (DSC) as a basic study for the enhancement of Jc. Interfacial reactions of Cu/NbTi multilayer thin films and superconducting wires were investigated with optical microscope, SEM, and XRD. According to the effective heat of formation (EHF) model, CU$\_$3/Ti was predicted as a first phase. However, considering the crystalline structure and thermodynamics, CuTi was predicted as a first phase. According to the results of DSC and XRD, CU$\_$2/Ti was found to be the first phase, followed by the formation Of CU$\_$4/Ti. The difference in first crystalline phase between the experimental result and the predicted one was discussed. In case of Cu/NbTi superconducting wires, the compounds formed at the Cu/NbTi interface grew with annealing time and the amount of compounds formed in Nb-47wt%Ti alloy was larger than that in Nb-50wt%Ti alloy. It seemed that the incubation time for the formation of compounds in Nb-50wt%Ti alloy was longer than that formed in Nb-47wt%Ti alloy. Also, the diffusion was the rate controlling step for the growth of compounds in all specimens. These compounds were formed at 500-600.deg. C for I hour annealing and, thus, the drawing time below I hour must be required to minimize the growth of compounds for the enhancement of Jc.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1472-1474
• /
• 1997

In this study, the $Nb_3Sn$ wire was tried to fabricate by internal tin process to investigate the relationship between the processing parameters in a cold working and the microstructure. The critical current densities of $Nb_3Sn$ wires were evaluated in magnetic fields at 4.2 K. $Nb_3Sn$ compound layer was found to be formed between Nb core and Cu-Sn. The Cu part in the wire transformed to Cu-Sn by the reaction with Sn and the Sn in the Cu-Sn part reacted with Nb.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.211-215
• /
• 2011

The dynamic magnetostriction characteristics of an Fe-based nanocrystalline FeCuNbSiB alloy are investigated as a function of the dc bias magnetic field. The experimental results show that the piezomagnetic coefficient of FeCuNbSiB is about 2.1 times higher than that of Terfenol-D at the low dc magnetic bias $H_{dc}$ = 46 Oe. Moreover, FeCuNbSiB has a large resonant dynamic strain coefficient at quite low Hdc due to a high mechanical quality factor, which is 3-5 times greater than that of Terfenol-D at the same low $H_{dc}$. Based on such magnetostriction characteristics, we fabricate a new type of transducer with FeCuNbSiB/PZT-8/FeCuNbSiB. Its maximum resonant magnetoelectric voltage coefficient achieves ~10 V/Oe. The ME output power reaches 331.8 ${\mu}W$ at an optimum load resistance of 7 $k{\Omega}$ under 0.4 Oe ac magnetic field, which is 50 times higher than that of the previous ultrasonic-horn-substrate composite transducer and it decreases the size by nearly 86%. The performance indicate that the FeCuNbSiB/PZT-8/FeCuNbSiB transducer is promising for application in highly efficient magnetoelectric energy conversion.