• Journal of Welding and Joining
• /
• v.18 no.6
• /
• pp.74-82
• /
• 2000

The fluxless wetting properties of UBM-coated Si-wafer to the binary lead-free solders(Sn-Ag, Sn-Sb, Sjn-In, Sn0Bi) were estimated by wetting balance method. With the new wettability indices from the wetting curves of one side coated specimen, the wetting property estimation of UBM-coated Si-wafer was possible. For UBM of Si-chip, Au/Cu/Cr UBm was better than au/Ni/TI in the point of wetting time/ At general reflow process temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) was better than that of low melting point one(Sn-Bi, Sn-In). The contact angle of the one side coated Si-plate to the solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.

• Structural Engineering and Mechanics
• /
• v.52 no.5
• /
• pp.957-969
• /
• 2014

Among severe plastic deformation methods, groove pressing is one of the prominent techniques for producing ultra-fine grained sheet materials. This process consists of imposing repetitive severe plastic deformation on the plate or sheet metals through alternate pressing. In the current study, a 2 mm pure Cu sheet has been subjected to repetitive shear deformation up to two passes. Hardness and tensile yield and ultimate stress were obtained after groove pressing. Fracture toughness tests have been performed and compared for three conditions of sheet material namely as received (initial annealed state), after one and two passes of groove pressing. Results of experiments indicate that a decrease in the values of fracture toughness attains as the number of constrained groove pressing (CGP) passes increase.

• Proceedings of the KSR Conference
• /
• 2002.05a
• /
• pp.549-554
• /
• 2002

Recently, interest in hygiene has been arouse in the health care field. Consequently, Filters with antibacterial agent applied to improve air quality by sterilizing bacteria, fungi, etc. We actually installed antibacterial air filter containing 2.5wt%Ag zeolite on the air intake route to air-conditioner in passenger cu, and evaluated filter's performance on antibacterial effect. By the microbe liquid spattering method, we found that the antibacterial air filter has notably sufficient antibacterial efficiency against standard strains and wild type strains. Antibacterial effect was observed at whole area of filter media by zone of inhibition test. The evaluation of microbe quantity was conducted through mixing dilution plate culture method. In comparison with ordinary filter, the amount of germs attached on antibacterial air filters was larger. The amount of germs attached on ordinary filters was very small since ordinary filters contained less dust. In comparison in antibacterial air filter with thickness, the amount of germs attached on 9mm filter was smaller than that of on 6mm filter. i.e. thicker filter, superior efficiency.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.18-19
• /
• 2020

The ElectroMagnetic Pulse (EMP) destroys social infrastructure at once and causes social chaos. However, currently major infrastructures are constructed of concrete that does not have electromagnetic shielding performance. In this study, using the arc metal spraying method is used to evaluate the shielding performance and construction performance of concrete. The electro-magnetic shielding effect is measured by fabricating a shielding room with reference to MIL-STD-188-125, and the construction performance is evaluated by measuring the adhesion strength of thin metal sprayed film-concrete. As a result of the study, when the metal spraying method is applied, the shielding effect is higher than that of the special electro-magnetic shielding concrete, and it is considered to be more economical than the existing metal plate (3~5 mm).

• Korean Journal of Heritage: History & Science
• /
• v.53 no.2
• /
• pp.242-253
• /
• 2020

Six ornamental metal quiver fittings were excavated from stone chamber No.1 of the ancient tombs of Jeongchon, Bokam-ri, Naju. The ornamental quiver fittings are metal, but the body of the quiver was made of organic material, so that it corroded and disappeared in the burial environment. The ornamental metal quiver fittings were made in pairs, and decorated one quiver according to the location they were found in and their forms. The ornamental metal quiver fitting can be divided into two types: A band style ornament (帶輪狀金具) which decorates the arrow pouch, and a board style ornament (板狀金具) which decorates the board connecting the waist belt. Two ornamental metal quiver fittings excavated from wooden coffin 2 of stone chamber No.1, were made in the band style, while the ornamental metal quiver fittings from southeast of stone chamber No.1 were identified as two boardstyle ornaments and two band-style ornaments for what was presumed to be belt loops. Material analysis of the ornamental metal quiver fittings shows that they are made of a gilt bronze plate attached to an iron plate, and the surface is marked with a speck of chisel to make lines and patterns. Chemical composition analysis (XRF) established that 24~40wt% Au and 50~93wt% Cu were detected on the gold surface, and it was confirmed that bronze corrosion had taken place on the gilt surface. SEM-EDS analysis of the gold plating layer identified a working line for glossing, and 7~9wt% Hg and an amalgam of gilt layers was detected, confirming the amalgam gilding. CT and FT-IR analysis established that the band style was double-layered with silk fabric under the iron plate, and there was also a lacquer piece underneath. The band-style ornaments have two layers of silk under the iron plate, along with lacquer pieces. Adding the fabric to the arrow pouch increases adhesion and decorative value. It is assumed that the lacquer pieces indicate that the surface of the lacquered arrow pouch had fallen together with the ornaments. On the other hand, the board-style ornaments have a thick layer of organic matter under the iron plate, but this is difficult to identify and appears to be a remnant of the quiver board. The characteristics of these ornamental metal quiver fittings were similar in Baekje, Silla, and Gaya cultures from the late 4th to the late 5th centuries, and enable us to identify the art of ancient gold craftwork at that time.

• Journal of Advanced Technology Convergence
• /
• v.1 no.2
• /
• pp.11-17
• /
• 2022

The purpose is to find out where medical workers can receive the minimum radiation does in clinical. In order to sett RQR standard quality of radiation, put a Al 1.5mm filter(row and column: 10 cm × 10 cm) on X-ray tube. Al 0.9 mm, Cu 0.3 mm, Ni 0.3 mm used as a filter. The Acrylic phantom were set to 13.1 cm, 18.5 cm, 21.1 cm. by the object thickness was different. As a results, when we use Al 0.9 mm, 1853 nSv was the highest numeral. It is a point of anode low 50 cm, when we use 13.1 cm Acrylic phantom. When we use Cu 0.3 mm, 173 nSv was the lowest numeral. It is a point of anode low 150 cm, when we use 13.1 cm Acrylic Phantom. In this study, it was confirmed that the spatial scattering dose decreased as the distance from the X-ray tube increased. It is considered that more studies on the exposure of scattered doses are needed in the future.

• Journal of Conservation Science
• /
• v.31 no.3
• /
• pp.193-214
• /
• 2015

The green pigments of shamanic paintings (83 items) in the 19~20th century were analyzed with X-ray fluorescent spectrometer(XRF), scanning electron microscopy (SEM) and fourier transform infrared spectroscopy (ATR-FTIR). In 60 items, copper and arsenic were detected in green pigments of the paintings by XRF spectra. Cu $K{\alpha}$/As $K{\beta}$ (peak intensity ratio of copper and arsenic) of shamanic paintings of Bokgaedang (shrine), solemn paintings (romance of three kingdoms) of Donggwanwangmyo and unknown enshrined place were 5.93~12.04 and higher compared to 5.67-6.26 of standard emerald greens and 4.01~7.89 of remaining shamanic paintings. The SEM images of crystal forms of copper-arsenic green pigments were various. Crystal forms were divided into oval and round spherulite with intersecting plate crystals and spherulite with agglomerate plate crystals. The crystals of the latter were found in shamanic paintings of Bokgaedang (shrine), solemn paintings (romance of three kingdoms) of Donggwanwangmyo and unknown enshrined place and the former were found in the rest of shamanic paintings. Copper-arsenic green pigments of shamanic paintings were identified as Scheele's green from shamanic paintings of Bokgaedang (shrine) and romance of three kingdoms. Emerald green from the rest of shamanic paintings by ATR-FTIR. From analytical results, it is confirmed that Scheele's green of shamanic paintings of Bokgaedang and romance of three kingdoms was used in the 1850s~1870s and emerald green had been widely used from late 19th century to 1970 in the rest of shamanic paintings.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.341-350
• /
• 1996

The CdS thin films are grown on quartz plate by hot wall epitaxy. The source and substrate temperature is $590^{\circ}C$ and $400^{\circ}C$ respectively, and thickness of the film is $2.5\;\mu\textrm{m}$. Using extrapolation method of X-ray diffraction patterns for the CdS thin film, it was found hexagonal structure whose lattice constant a and c were $4.137\;{\AA}$ and $6.713\;{\AA}$, respectively. Hall effect on this sample was measured by the method of van der Pauw and studied on cattirer density and mobility depending on temperature. From hall data, the mobility was likely to be decreased by piezoelectric scattering in the temperature range 30 K to 200 K and by polar optical scattering in the temperature range 200 K to 293 K. In order to explore the applicability as a photoconductive cell we measured the sensitivity ($\gamma$), the ratio of photocurrent to darkcurrent (pc/dc), maximum allowable power dissipation (MAPD), spectral response and response time. The results indicated that for the samples annealed in Cu vapor the photoconductive characteristics are the best. Then we obtained the sensitivity of 0.99, the value of pc/dc of $9.42{\times}10^{6}$, the MAPD of 318 mW, and the rise and decay time of 10 ms and 9 ms, respectively.

• Journal of the Korean Chemical Society
• /
• v.53 no.3
• /
• pp.368-376
• /
• 2009

In this study we investigated and tried to understand problems monitored in an experiment on reactivity of metals in chemistry I. Three problems were discussed. First, the reason that aluminium plate does not react with other metal ions such as zinc, iron and copper was studied and the way to overcome this problem was suggested. Second, the reason that the bubbles were generated when FeS$O_4$(aq) and Zn(s) react was discussed. Third, the precipitates which appeared in the reaction of FeS$O_4$(aq) and Zn(s) were identified. Through reference study and experimental investigation, we could reach the following results. First, aluminium could not react with other metal ions due to the surface oxide layer that is formed very fast and prevents aluminium from reacting with metal ions in solution. This problem could be overcome by allowing a competing reaction of acid and aluminium during the reaction of aluminium and metal ions. Second, the observed bubbles were identified to be hydrogen gas, produced by the reaction between metals and hydronium ion in the solution. Third, black precipitates that were produced on the surface of zinc plate and exhibited magnetic property were characterized to be $Fe_3O_4$(s), and brown precipitates that were produced in the solution phase were to be $Fe_2O_3$(s) by the analysis of X-ray photoelectron spectra.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.55-62
• /
• 2000

The wetting balance test was performed in an attempt to estimate the wetting properties of the UBM-coated Si-wafer on one side to the Sn-Pb solder. The wetting curves of the one and both side-coated UBM layers had the similar shape and the parameters characterizing the curve shape showed the similar transition tendency to the temperature. The wetting property estimation was possible with the new wettability indices from the wetting curves of one side-coated specimen; $F_{min}$, $F_{s}t_{s}$ and $t_s$. For UBM of Si-chip, Au/Cu/Cr UBM was better than Au/Ni/Ti in the point of wetting time. The contact angle of the one side coated Si-plate to the Sn-Pb solder could be calculated from the force balance equation by measuring the static state force and the tilt angle.