• 한국전기전자재료학회논문지
• /
• 제34권2호
• /
• pp.126-129
• /
• 2021

We fabricated plate typed shunt resistors composed of carbon nanotube (CNT) and metal alloy for measuring DC current. CNT plates were prepared from dispersed CNT/Urethane solution by squeezing method. Cu/Ni alloys were prepared from composition-designed alloy wires for adjusting the temperature coefficient of resistance (TCR) by pressing them. As well, we fabricated a hybrid resistor by squeezing the CNT/Urethane solution on the metal alloy plate directly. In order to confirm the composition ratio of the Cu/Ni alloy, we used an energy-dispersed X-ray spectroscopy (EDX). Cross-section and surface morphology were analyzed by using a scanning electron microscopy (SEM). Finally, we measured the initial resistance of 2.35 Ω at 25℃ for the CNT paper resistor, 7.56 mΩ for the alloy resistor, and 7.38 mΩ for the hybrid resistor. The TCR was also measured to be -778.72 ppm/℃ at the temperature range between 25℃ to 125℃ for the CNT paper resistor, 824.06 ppm/℃ for the alloy resistor, and 17.61 ppm/℃ for the hybrid resistor. Some of the hybrid resistors showed a near-zero TCR of 1.38, -2.77, 2.66, and 5.49 ppm/℃, which might be the world best-value ever reported. Consequently, we could expect an error-free measurement of the DC current using this resistor.

• Tuberculosis and Respiratory Diseases
• /
• 제42권4호
• /
• pp.522-534
• /
• 1995

연구배경: 내독소에 의한 급성 폐손상의 발병기전에서 산소기가 중요한 역할을 한다는 사실은 잘 알려져 있다. 세포내에는 이러한 산소기에 의한 세포의 손상을 방지하는 정상 방어기전으로 여러 항산화효소가 존재하는데, 이중 SOD는 세포대사과정이나 외부 자극에 의해 생성된 superoxide로부터 세포의 손상을 방지하는 역할을 한다. 세포내 SOD는 주로 이중체의 구조로 세포질에 존재하는 CuZnSOD와 사중체의 구조로 미토콘드리아에 존재하는 MnSOD의 두 종류가 알려져 있으나, 폐포대식세포에서의 SOD mRNA 발현 및 그 조절기전에 대해서는 확실히 규명되어 있지 않다. 본 연구의 목적은 백서의 폐포대식세포에서 내독소 자극에 의한 MnSOD와 CuZnSOD mRNA 발현양상을 관찰하고 내독소 자극시 니타나는 SOD mRNA 발현의 조절기전을 규명하는데 있다. 방법: 백서의 기관지폐포세척액에서 얻은 세포를 plastic plate에 부착시켜 폐포대식세포를 분리한 후 내독소를 자극하여 내독소 용량($0.01{\mu}g/ml{\sim}10{\mu}g/ml$)과 자극시간(0, 2, 4, 8, 24 hrs)에 따른 MnSOD와 CuZnSOD MnSOD 발현양상을 Northern blot analysis를 시행하여 관찰하였다. 다음 단계로 MsSOD와 CuZnSOD mRNA 발현의 조절기전을 밝히고자 폐포대식세포를 각각 AD($5{\mu}g/ml$) 또는 CHX($5{\mu}g/ml$)로 전처치한 후 내독소로 자극하여 MnSOD와 CuZnSOD mRNA의 발현양상을 관찰하였다. 한편 내독소 투여가 SOD mRNA의 안정성을 변화시키는지 여부를 평가하기 위해 폐포대식세포를 대조군과 투여군으로 나누어 SOD mRNA의 분해속도를 비교하였다. 총 세포내 RNA는 guanidinium thiocyanate/phenol/chloroform법을 이용하여 추출하였고, Northern blot analysis는 $^{32}P$로 표지된 백서의 MnSOD와 CuZnSOD cDNAs를 이용하여 시행하였다. 결과: 백서의 폐포대식세포에서 MnSOD mRNA의 발현은 내독소 투여량의 증가세 따라 증가되었고 내독소를 투여하고 8시간후에 정점을 이루었으나, CuZnSOD mRNA의 발현은 내독소의 용량 및 투여후 반응시간에 따라 변화하지 않았다. 내독소 투여후 MnSOD mRNA의 발현증가는 AD 또는 CHX 각각의 전처치에 의해 모두 억제되었다. MnSOD mRNA의 안정성은 내독소 투여에 의해 변화하지 않았다. 결론: 이상의 결과로 백서의 폐포대식세포는 내독소 자극에 반응하여 SOD를 생성하는 중요세포이고, 내독소에 의한 MnSOD mRNA의 발현은 전사단계에서 조정되며 mRNA의 안정성을 변화시키지 않고 새로운 단백의 합성이 필요한 것으로 사료된다.

• Journal of Radiation Protection and Research
• /
• 제42권3호
• /
• pp.141-145
• /
• 2017

Background: The concrete walls inside the vaults of cyclotron facilities are activated by neutrons emitted by the targets during radioisotope production. Reducing the amount of radioactive waste created in such facilities is very important in case they are decommissioned. Thus, we proposed a strategy of reducing the neutron activation of the concrete walls in cyclotrons during operation. Materials and Methods: A polyethylene plate and B-doped Al sheet (30 wt% of B and 2.5 mm in thickness) were placed in front of the wall in the cyclotron room of a radioisotope production facility for pharmaceutical use. The target was Xe gas, and a Cu block was utilized for proton dumping. The irradiation time, proton energy, and beam current were 8 hours, 30 MeV, and $125{\mu}A$, respectively. To determine a suitable thickness for the polyethylene plate set in front of the B-doped Al sheet, the neutron-reducing effects achieved by inserting such sheets at several depths within polyethylene plate stacks were evaluated. The neutron fluence was monitored using an activation detector and 20-g on de Au foil samples with and without 0.5-mm-thick Cd foil. Each Au foil sample was pasted onto the center of a polyethylene plate and B-doped Al sheet, and the absolute activity of one Au foil sample was measured as a standard using a Ge detector. The resulting relative activities were obtained by calculating the ratio of the photostimulated luminescence of each foil sample to that of the standard Au foil. Results and Discussion: When the combination of a 4-cm-thick polyethylene plate and B-doped Al sheet was employed, the thermal neutron rate was reduced by 78%. Conclusion: The combination of a 4-cm-thick polyethylene plate and B-doped Al sheet effectively reduced the neutron activation of the investigated concrete wall.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2001년도 총회 및 춘계학술발표회
• /
• pp.11-14
• /
• 2001

In this study, the relationship between metals (Cu, Cr, Cd, Zn. Pb, and Fe) 5 fractions and toxicity of soil samples from various contaminated sites in Korea were investigated. Metal toxicity of soils was tested using MetPLATE$^{TM}$ test kit, which is known as metal sensitive and organic insensitive. Significant amount of Fe was found in soils, and metal contents were in the order of Fe>Zn>Pb>Cu>Cr>Cd. Metal levels in organic fraction were rather high for all metals except Fe, and quite high percentages (35~79%) for residual fraction were observed for all metals. There were no significant relationships between the content of each metal fraction and toxicity which showed regression $R^2$in the range of 0.0003~0.414. However, correlation between toxicity and total metal contents showed regression coefficient $R^2$= 0.72. These results showed that the risk evaluation of metals in contaminated sites should be difficult to assess only by the contents of metal distribution because of the complexity of mixture of various metals.s.

• Bulletin of the Korean Chemical Society
• /
• 제29권1호
• /
• pp.69-75
• /
• 2008

Tautomerism of pyrimidine base cytosine has been comparatively examined on nanoparticle and roughened plate surfaces of silver, gold, and copper by surface-enhanced Raman scattering (SERS). The SERS spectrum was found to be different depending on the metals and their substrate conditions suggesting the dissimilar population of various tautomers of cytosine on the surfaces. The ab initio calculations were performed at the levels of B3LYP, HF, and MP2 levels of theory with the LanL2DZ basis set to estimate the energetic stability of the tautomers with the metal complexes as well as the gas phase state. The amino group and N3-coordinated tautomer was predicted to be more favorable for bonding to Au, whereas the hydroxyl and N1-coordinated zwitter ionic form is most stable with Ag and Cu as a bidentate form from the DFT calculation. The binding energy with the Ag atom is calculated to be smaller than those with the Au and Cu atoms in line with the temperature-dependent SERS spectra of cytosine.

• 한국세라믹학회지
• /
• 제31권7호
• /
• pp.715-722
• /
• 1994

Off-axis supttering using shielder was used to efficiently prevent negative oxygen ions from resputtering deposited films. In this method, the substrate was located vertically to the target and shielded by the semicircled steel plate. By using this method, the resputtering could be reduced, and 2223 high-Tc phase could be formed at the lower substrate temperature and in the broader temperature region. As increasing the substrate temperature, 2212, 2223, 2212 superconducting phases were formed by turns. 2223 phase was formed above 2$\times$10-2 torr, and 2212 phase was formed above 4$\times$10-2 torr.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.184-193
• /
• 2003

Cyclic sweep voltametry was performed to investigate the electrochemical behavior of heavy metal ions and the organic additives in surface finishing process. And electrolysis using parallel plate electrode electrolyzer was carried out to simulate the treatment of real waste water. Results showed that more than 99 percent of Cu was recovered and selective recovery of Cu in mixed waste water was possible, but the possibility of economical recovery of Ni and Cr were very low due to the evolution of hydrogen gas. Electrochemical oxidation of cyanide and organic additives on anode showed very excellent removal rate. The complete removal of several hundred ppm of cynide was possible within several tens minutes and organics within 2 or 3 hours. Even in case of concentrate waste water, the complete removal of COD by using NaCl and air stirring seemed to be possible.

• 한국세라믹학회지
• /
• 제29권2호
• /
• pp.95-100
• /
• 1992

A high-Tc superconducting phase was obtained using long sintering time of 210 hours. From XRD and SEM analyses, it could be confirmed that the particles were plate phase, of which the structure is tetragonal system with lattice parameter a=b=5.44${\AA}$, C=37.18${\AA}$. Resistance and current density measurements were carried out using 4 probe method. The experimental data revealed that the stable high-Tc superconducting phase was easily formed by addition of Pb to Bi-system. Therefore, we could find the sintering condition to synthesis the system having the largest fraction of high Tc phase.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.377-378
• /
• 2006

Thermal management technology is a critical element in all new chip generations, caused by a power multiplication combined with a size reduction. A heat sink, mounted on a base plate, requires the use of special materials possessing both high thermal conductivity (TC) and a coefficient of thermal expansion (CTE) that matches semiconductor materials as well as certain packaging ceramics. In this study, nano tungsten coated copper powder has been developed with a wide range of compositions, 90W-10Cu to 10W-90Cu. Powder technologies were used to make samples to evaluate density, TC, and CTE. Measured TC lies among theoretical values predicted by several existing models.

• 한국분말재료학회지
• /
• 제22권2호
• /
• pp.134-137
• /
• 2015

The monolayer engineering diamond particles are aligned on the oxygen free Cu plates with electroless Ni plating layer. The mean diamond particle sizes of 15, 23 and $50{\mu}m$ are used as thermal conductivity pathway for fabricating metal/carbon multi-layer composite material systems. Interconnected void structure of irregular shaped diamond particles allow dense electroless Ni plating layer on Cu plate and fixing them with 37-43% Ni thickness of their mean diameter. The thermal conductivity decrease with increasing measurement temperature up to $150^{\circ}C$ in all diamond size conditions. When the diamond particle size is increased from $15{\mu}m$ to $50{\mu}m$ (Max. 304 W/mK at room temperature) tended to increase thermal conductivity, because the volume fraction of diamond is increased inside plating layer.