• 한국세라믹학회지
• /
• 제54권1호
• /
• pp.61-65
• /
• 2017

Examined in this study were the effects of copper oxide (II) addition and sintering conditions on the chromatic characteristics of copper glaze. Oxidatively sintered samples exhibited the negative increase of $CIEa^*$ and the positive increase of $CIEb^*$ with the increase of CuO concentration, leading to Green and Green-Yellow coloration. On the other hand, $CIEa^*$ and $CIEb^*$ of reductively sintered samples were positively increased in direct proportion. The green color of oxidatively sintered samples was originated from the $Cu^{2+}$ ions formed by the dissolution of CuO. The reductively sintered samples resulted in dull tone red color with low chroma. Such behavior seems to be influenced by the interplay of metal Cu aggregation, metal Cu globule, and $Cu_2O$ formed in the glaze layer through the redox interaction of CuO during the sintering process.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.580-581
• /
• 2006

The present paper investigates the possibilities of niobium using for the mechanical properties of the common low alloyed Cu-Ni-Mo-C sintered structural steels enhancing. On both thermodynamic and experimental bases there were demonstrated the Nb nitrides/carbides/carbonitrides preferential formation in these steels during sintering in dissociated ammonia at both common and elevated temperatures. The obtained results for $0.2\;{\div}\;1.0\;%$ fine Nb powder and 0.3% graphite additions to Distaloy AB iron base powder cold compacted and sintered in dissociated ammonia proved the expected strengthening effect, leading to higher mechanical properties of the processed steels than of the common Cu-Ni-Mo-C ones.

• 자원환경지질
• /
• 제29권3호
• /
• pp.305-313
• /
• 1996

In order to investigate the extent and degree of Cd, Cu, Pb and Zn contamination affected by mining activities of the Dalsung Cu~W mine, sampling of stream sediments and waters has been undertaken up to 1.5 km downstream from the mine at 50~150 meter intervals. Analysis of the samples was carried out using ICP-AES for Cd, Cu, Pb and Zn. Physical and chemical properties of sediments (pH, organic matter contents, cation exchange capacity) and waters (pH, Eh and temperature) were also measured. The properties of the sediment samples were characterized by low pH (3.0~5.5), low organic matter contents (2~5%) and a moderate degree of cation exchange capacity (7~15 meq/100 g) with a high proportion of sand fraction. The pH values of water samples ranged from 3.0 to 5.0 and the Eh levels were in the range of 350~530 mV. Concentrations of Cd, Cu, Pb and Zn in the sediments averaged 3.2 mg/kg, 1,390 mg/kg, 451 mg/kg and 262 mg/kg with the range of 0.6~11.4 mg/kg, 15~3,800 mg/kg, 14~1,330 mg/kg and 63~1,060 mg/kg, respectively. Significant levels of the heavy metals were also found in the water samples with the range of $10{\sim}170{\mu}gCd/l$, $300{\sim}41,600{\mu}gCu/l$, $10{\sim}80{\mu}gPb/l$ and $700{\sim}15,400{\mu}gZn/l$. These elevated concentrations in the sediments and waters may be caused by the weathering of mine waste materials and their high solubilities under acidic and/or oxidizing conditions. Although metal concentrations in the samples decrease with the distance from the mine, heavy metal contamination of sediments and waters were also found at the 1.5 km downstream due to the mobile conditions of the heavy metals, with particular reference to Cd and Zn in stream waters.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.444-445
• /
• 2009

The metallic contact system of silicon solar cell must have several properties, such as low contact resistance, easy application and good adhesion. Ni is shown to be a suitable barrier to Cu diffusion as well as desirable contact metal to silicon. Nickel monosilicide(NiSi) has been suggested as a suitable silicide due to its lower resistivity, lower sintering temperature and lower layer stress than $TiSi_2$. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on $0.2\sim0.6\;{\Omega}{\cdot}cm$, $20\;\times\;20\;mm^2$, CZ(Czochralski) wafer.

• 한국자기학회지
• /
• 제17권6호
• /
• pp.232-237
• /
• 2007

기본조성 $(Ni_{0.2}Cu_{0.2}Zn_{0.6})_{1+x}(Fe_2O_3)_{1-x}$에서 $Fe_2O_3$가 약간 부족한 비화학양론적인 조성비를 택하여 Ni-Zn-Cu 페라이트의 입계에 높은 저항층을 형성하고 소결을 촉진시켜 낮은 손실, 높은 투자율 및 자기유도 와 주성분을 치환해서 스피넬 격자를 고용시킬 목적으로 $TiO_2$ 및 $Li_2CO_3$를 소량 첨가하였다. 이들 원료들을 혼합한 후 가소 후 소결온도 $875^{\circ}C,\;900^{\circ}C,\;925^{\circ}C$ 및 $950^{\circ}C$에서 소결하였다. 각 시편들에 대한 소결밀도는 $4.85\sim5.32g/cm^3$으로 나타났고, 각 시편들의 고유저항은 $10^8\sim10^{12}\Omega-cm$으로 측정되었다. 시편들의 자기유도 특성 값은 대략 $800\sim1300G$ 부근이었으며, $TiO_2$를 첨가한 경우보다 $Li_2CO_3$를 첨가한 경우가 약간 높게 측정되었다. 각각 시편들의 보자력은 $2.5\sim4.5$ Oe로 연자성 재료의 범위로 나타났다. 초투자율 및 품질계수는 각각 $125\sim275$ 및 $65\sim83$으로 나타나 Ni-Zn-Cu 페라미트에서 측정되는 값들과 대동소이했다. 물리적인 특성값(고유저항, 자기유도, 초투자율, 품질계수 등)으로 미루어 보마 각종 고주파영역(microwave영역까지 포함) 통신기기 코어 및 편향 요크 코어 등으로 응용이 가능하다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제3권3호
• /
• pp.114-121
• /
• 2003

Through comparing stress state of TEOS and SiLK-embedded structures, the effect of low-k materials on stress and stress distribution in via-line structures were investigated using three-dimensional finite element analyses. In the case of TEOS-embedded via-line structures, hydrostatic stress was concentrated at the via and the top of the lines, where the void was suspected to nucleate. On the other hand, in the via-line structures integrated with SiLK, large von-Mises stress is maintained at the via, thus deformation of via is expected as the main failure mode. A good correlation between the calculated results and experimentally observed failure modes according to dielectric materials was obtained.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.913-916
• /
• 2001

From 1994 the cooperation between NEU of China and MJU of South Korea for study of ReBaCuO (Re=Rare earth elements) superconductors has been carried out. The progress has been got in following projects. Critical current density ($J_c$) of YBaCuO superconductor prepared by Melting Textured Growth (MTG) was improved. In the preparation of textured YBaCuO, 20 wt.% of YBaCuO 211 phase was added, which would be climactic for the microcracks in the textured YBaCuO. The effects of the 211 phase and Ag content on the superconductivity were studied and discussed in detail. The improved $J_c$ value was reached to 8$\times$10^4 A/cm^2 (77K,0T). Single phase $YbBa_{2}Cu_{3}O_{x}$ superconductor was sintered by the traditional powder metallurgical method, and its reaction process was studied. In recent years, NdBaCuO superconductor is being performed. The behavior of $Nd_{4}Ba_{2}Cu_{2}O_{10}$(Nd422 phase) and the solid solubility, x in the superconductor $Nd_{1+x}Ba_{2-x}Cu_{3}O_{y}$ by the heat treatment in the low oxygen partial pressure (1%) or Ar at $950{\circ}C$ were investigated. The zone-melting process was used to make oriented NdBaCuO superconductor in order to increase the critical current density.

• 한국재료학회지
• /
• 제14권8호
• /
• pp.595-599
• /
• 2004

We investigated the structural, electrical and magnetic properties of Mn-doped $CuAlO_2$ delafossite ceramics ($CuAl_{1-x}Mn_{x}O_2,\;0\le\;x\;\le0.05$), synthesized by solid-state reaction method in an air atmosphere at a sintering temperature of $1150^{\circ}C$. The solubility limit of Mn ions in delafossite $CuAlO_2$ was found to be as low as about 3 $mol\%$. Positive Hall coefficient and the temperature dependence of conductivity established that non-doped $CuAlO_2$ ceramic is a variable-range hopping p-type semiconductor. It was found that the Mn-doping in $CuAlO_2$ rapidly reduced the hole concentration and conductivity, indicating compensation of free holes. The analysis of the magnetization data provided an evidence that antiferromagnetic superexchange interaction is the dominant mechanism of the exchange coupling between Mn ions in $CuAl_{1-x}Mn_{x}O$ alloy, leading to an almost paramagnetic behavior in this alloy.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.1019-1022
• /
• 2004

본 연구에서는 PERC(passivated emitter and rear cell) 구조를 갖는 고효율 단결정 실리콘 태양전지에 도금법을 적용하여 Ni/Cu 전극을 형성하였다. 고효율 태양전지는 제작 비용이 높고 공정이 복잡하기 때문에 실용화에 적용이 어려운 단점이 있다. 따라서 태양전지의 효율은 그대로 유지하고, 공정을 간단하게 줄이면서 저가격화 할 수 있는 방법에 대한 연구가 필요하다. 기존의 고효율 실리콘 태양전지에 가장 일반적으로 적용되고 있는 Ti/Pd/Ag 전극의 경우 고가의 증착 장비를 이용할 뿐만 아니라 재료 자체도 매우 고가의 물질이 사용되고 있다. 도금법으로 Ni/cu 전극을 형성하여 태양전지를 제작한 결과 공정을 간소화하고 비용을 절감 하면서, 20% 이상의 고효율 태양전지를 얻을 수 있었다.

• 한국분말재료학회지
• /
• 제25권1호
• /
• pp.19-24
• /
• 2018

Cu-Fe alloys (CFAs) are much anticipated for use in electrical contacts, magnetic recorders, and sensors. The low cost of Fe has inspired the investigation of these alloys as possible replacements for high-cost Cu-Nb and Cu-Ag alloys. Here, alloys of Cu and Fe having compositions of $Cu_{100-x}Fe_x$ (x = 10, 30, and 50 wt.%) are prepared by gas atomization and characterized microstructurally and structurally based on composition and powder size with scanning electron microscopy (SEM) and X-ray diffraction (XRD). Grain sizes and Fe-rich particle sizes are measured and relationships among composition, powder size, and grain size are established. Same-sized powders of different compositions yield different microstructures, as do differently sized powders of equal composition. No atomic-level alloying is observed in the CFAs under the experimental conditions.