• 센서학회지
• /
• 제5권1호
• /
• pp.71-77
• /
• 1996

마이크로머시닝의 구조재료인 다결정 Si이 희생산화막의 영향을 받음을 고려하여 다결정 Si을 열산화시킨 다결정-산화막을 새로운 희생산화막의 재료로서 제안하고 평가하였다. 다결정-산화막상에 성장시킨 다결정 Si은 통상의 희생산화막상에 성장시키는 경우보다 grain size가 증가하였고, XRD결과를 통해 (111) texture의 증가와, 부가적인 (220) texture가 형성됨을 관찰하였다. 또한, 다결정-산화막상에 성장시킨 다결정 Si의 경우, 그 응력이 작고 균일한 분포를 나타내었다.

• 한국표면공학회지
• /
• 제27권2호
• /
• pp.83-90
• /
• 1994

We have investigated the mechanism for the abnormal oxide growth occuring during oxidation of the crystalline tungsten silicide. TEM and XPS analysis reveal the abnormaly grown oxide layer consisting of crystalline $Wo_3$ and amorphous $SiO_2$. The presence of crystalline $Wo_3$ provides a rapid diffusion of oxygen through the oxide layer. The abnormal oxide growth is mainly due to the poor quality of initial oxide layer growth on tungsten silicide. Two species such as tungsten and silicon from decomposition fo tungsten silicide as well as silicon supplied from the underlying polysilicon are the main contributors sto abnormal oxide forma-tion. Consequently, the abnormal oxidation results in the disintegration of tungsten silicide and thinning of polysilicon as well.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.406-406
• /
• 2016

To get high efficiency n-type crystalline silicon solar cells, passivation is one of the key factor. Tunnel oxide (SiO2) reduce surface recombination as a passivation layer and it does not constrict the majority carrier flow. In this work, the passivation quality enhanced by different chemical solution such as HNO3, H2SO4:H2O2 and DI-water to make thin tunnel oxide layer on n-type crystalline silicon wafer and changes of characteristics by subsequent annealing process and firing process after phosphorus doped amorphous silicon (a-Si:H) deposition. The tunneling of carrier through oxide layer is checked through I-V measurement when the voltage is from -1 V to 1 V and interface state density also be calculated about $1{\times}1012cm-2eV-1$ using MIS (Metal-Insulator-Semiconductor) structure . Tunnel oxide produced by 68 wt% HNO3 for 5 min on $100^{\circ}C$, H2SO4:H2O2 for 5 min on $100^{\circ}C$ and DI-water for 60 min on $95^{\circ}C$. The oxide layer is measured thickness about 1.4~2.2 nm by spectral ellipsometry (SE) and properties as passivation layer by QSSPC (Quasi-Steady-state Photo Conductance). Tunnel oxide layer is capped with phosphorus doped amorphous silicon on both sides and additional annealing process improve lifetime from $3.25{\mu}s$ to $397{\mu}s$ and implied Voc from 544 mV to 690 mV after P-doped a-Si deposition, respectively. It will be expected that amorphous silicon is changed to poly silicon phase. Furthermore, lifetime and implied Voc were recovered by forming gas annealing (FGA) after firing process from $192{\mu}s$ to $786{\mu}s$. It is shown that the tunnel oxide layer is thermally stable.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.209-209
• /
• 2012

High-efficient transparent conductive oxide (TCO) film-embedding Si heterojunction solar cells were fabricated. An additional doping was not applied for heterojunction solar cells due to the spontaneous junction formation between TCO films and an n-type Si substrate. Three different TCO coatings were formed by sputtering method for an Al-doped ZnO (AZO) film, an indium-tin-oxide (ITO) film and double stacks of ITO/AZO films. An improved crystalline ITO film was grown on an AZO template upon hetero-epitaxial growth. This double TCO films-embedding Si heterojunction solar cell provided significantly enhanced efficiency of 9.23% as compared to the single TCO/Si devices. The effective arrangement of TCO films (ITO/AZO) provides benefits of a lower front contact resistance and a smaller band offset to Si leading enhanced photovoltaic performances. This demonstrates a potential scheme of the effective TCO film-embedding heterojunction Si solar cells.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.254-255
• /
• 2012

Interest in nano-crystalline silicon (nc-Si) thin films has been growing because of their favorable processing conditions for certain electronic devices. In particular, there has been an increase in the use of nc-Si thin films in photovoltaics for large solar cell panels and in thin film transistors for large flat panel displays. One of the most important material properties for these device applications is the macroscopic charge-carrier mobility. Hydrogenated amorphous silicon (a-Si:H) or nc-Si is a basic material in thin film transistors (TFTs). However, a-Si:H based devices have low carrier mobility and bias instability due to their metastable properties. The large number of trap sites and incomplete hydrogen passivation of a-Si:H film produce limited carrier transport. The basic electrical properties, including the carrier mobility and stability, of nc-Si TFTs might be superior to those of a-Si:H thin film. However, typical nc-Si thin films tend to have mobilities similar to a-Si films, although changes in the processing conditions can enhance the mobility. In polycrystalline silicon (poly-Si) thin films, the performance of the devices is strongly influenced by the boundaries between neighboring crystalline grains. These grain boundaries limit the conductance of macroscopic regions comprised of multiple grains. In much of the work on poly-Si thin films, it was shown that the performance of TFTs was largely determined by the number and location of the grain boundaries within the channel. Hence, efforts were made to reduce the total number of grain boundaries by increasing the average grain size. However, even a small number of grain boundaries can significantly reduce the macroscopic charge carrier mobility. The nano-crystalline or polymorphous-Si development for TFT and solar cells have been employed to compensate for disadvantage inherent to a-Si and micro-crystalline silicon (${\mu}$-Si). Recently, a novel process for deposition of nano-crystralline silicon (nc-Si) thin films at room temperature was developed using neutral beam assisted chemical vapor deposition (NBaCVD) with a neutral particle beam (NPB) source, which controls the energy of incident neutral particles in the range of 1~300 eV in order to enhance the atomic activation and crystalline of thin films at room temperature. In previous our experiments, we verified favorable properties of nc-Si thin films for certain electronic devices. During the formation of the nc-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. The more resent work on nc-Si thin film transistors (TFT) was done. We identified the performance of nc-Si TFT active channeal layers. The dependence of the performance of nc-Si TFT on the primary process parameters is explored. Raman, FT-IR and transmission electron microscope (TEM) were used to study the microstructures and the crystalline volume fraction of nc-Si films. The electric properties were investigated on Cr/SiO2/nc-Si metal-oxide-semiconductor (MOS) capacitors.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.71-76
• /
• 1995

The thermal oxidation of Ge$_{0.2}$Si$_{0.8}$ in wet ambient has been investigated by Rutherford Backscattering Spectrometry(RBS). A uniform Ge$_{0.2}$Si$_{0.8}$O$_{2}$ oxide is formed at temperatures below 650.deg. C for polycrystalline and below 700.deg. C for single crystalline substrates. At higher temperatures Ge becomes depleted from the oxide and finally SiO$_{2}$ oxide is formed with Ge piled-ub behind it. The transition between the different oxide types depends also on the crystallinity of Ge$_{0.2}$Si$_{0.8}$. When a uniform Ge$_{0.2}$Si$_{0}$8/O$_{2}$ oxide grows, its thickness is proportional to the square root of the oxidation time, which suggests that the rate noting process is the diffusive transport of oxidant across the oxide. It is believed the oxidation is controlled by the competition between the diffusion of Ge or Si in Ge$_{0.2}$Si$_{0.8}$ and the movement of oxidation front.t.oxidation front.t.

• 전자공학회논문지A
• /
• 제28A권10호
• /
• pp.814-820
• /
• 1991

TaSi$_2$ was formed by rapid thermal annealing(RTA) on BF$_2$ doped single crystalline silicon substrates. The formation and various properties of TaSi$_2$ have been investigated by using 4-point probe, HP414, XRD, and SEM. And the redistribution of boron with RTA has been observed by SIMS. Implanted boron was diffused out into the TaSi$_2$ for RTA temperature but did not significantly affect the formation temperature of TaSi$_2$. Also, the contact resistance for TaSi$_2$/p$^{+}$ region had a low value 22$\Omega$, at contact size of 0.9$\mu$m, and the native oxide formed on Si-substrates by BF$_2$ implantation retarded the formation of TaSi$_2$.

• 전자공학회논문지A
• /
• 제28A권5호
• /
• pp.380-386
• /
• 1991

Hydrogen plasma-assisted epitaxial(PAE) growth of GaAs/Si and GaAs/Ge/Si with Ge buffer layer has been investigated. By means of photoluminescence, Nomarski microscopu, and $\alpha$-step, it could be known that GaAs on Si with Ge buffer layer has better crystalline quality than GaAs on Si without Ge buffer layer. The stoichiometry of GaAs layer on Si was confirmed by the depth profile of Auger electron spectroscope (AES). Also the native oxide(SiO$_2$) layer on Si substrate was plama-etched and the removal of the oxide layer was confirmed by AES. Photoluminescence peak wavelength of GaAs/Ge/Si with Ge buffer of 1\ulcorner thickness and GaAs growth rate of 160$\AA$/min was 8700$\AA$and FWHM was 12$\AA$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.590-590
• /
• 2012

A transparent conducting oxide (TCO) layer was applied in crystalline Si (c-Si) solar cells without use of the conventional SiNx-coating. A high quality indium-tin-oxide (ITO) layer was directly deposited on an emitter layer of a Si wafer. Three different types of emitters were formed by controlling the phosphorous diffusion condition. A light-doped emitter forming a thinner emitter junction showed an improved photoconversion efficiency of 14.1% comparing to 13.2% of a heavy-doped emitter. This was induced by lower recombination within a narrower depletion region of the light-doped emitter. In the aspect of light management, the intermediate refractive index of ITO is effective to reduce the light reflection leading the enhanced carrier generation in a Si absorber. For the electrical aspect, the ITO layer serves as an efficient electrical conductor and thus relieves the burden of high contact resistance of the light-doped emitter. Additionally, the ITO works as a buffer layer of Ag and Si and certainly prevents the shunting problem of Ag penetration into Si emitter region. It discusses an efficient design scheme of TCO-embedded emitter Si solar cells.

• 한국산학기술학회논문지
• /
• 제19권1호
• /
• pp.699-704
• /
• 2018

일차원 나노구조물은 양자 갇힘 효과 및 나노와이어가 갖는 체적 대비 높은 표면적 비에 기인하는 독특한 전기적, 광학적, 광전기적, 전기화학적 특성으로 인하여 많은 주목을 받아왔다. 특히 수직으로 성장된 나노와이어는 체적 대비 높은 표면적 비의 특성을 나타낸다. VLS(Vapor-Liquid-Soild) 공정은 나노구조물의 성장 과정에서 자기정렬 효과 때문에 더욱 주목을 받는다. 본 연구에서는 두 영역 열화학 기상증착법을 이용하여 Si\$SiO_2$(300 nm)\Pt 기판 위에 수직으로 정렬된 실리콘 옥사이드 나노기둥을 VLS 공정으로 성장시켰다. 성장된 실리콘 옥사이드 나노기둥의 형상과 결정학적 특성을 주사전자현미경 및 투과전자현미경으로 분석하였다. 그 결과 성장된 실리콘 옥사이드 나노기둥의 지름과 길이는 촉매 박막의 두께에 따라 변하였다. 실리콘 옥사이드 나노 기둥의 몸체는 비정질 상을 나타내었으며, Si과 O로 구성되어 있었다. 또한 성장된 실리콘 옥사이드 나노 기둥의 머리는 결정성을 나타내었으며, Si, O, Pt 및 Ti으로 구성되어 있었다. 실리콘 옥사이드 나노 기둥의 수직 정렬은 촉매물질인 Pt/Ti 합금의 결정성 정렬 선호에 기인하는 것으로 판단되며, 수직 성장된 실리콘 옥사이드 나노기둥은 기능성 나노소재로 활용이 가능할 것으로 기대된다.