• 한국전산유체공학회지
• /
• 제14권2호
• /
• pp.9-18
• /
• 2009

The cargo containment system (CCS) for ships carrying cryogenic fluid consists of at least two levels of barriers and insulation layers. It is because, even though there is a small amount of leak through the primary barrier, the liquid tight secondary barrier blocks further leakage of the cryogenic fluid. However, once the secondary barrier is damaged, it is highly possible that the leaked cryogenic fluid flows through the flat joint made of glass wool and reaches the inner hull of the ship. The primary objective of the present study is to investigate the influence of the damage extent in the secondary barrier on the amount of leaked cryogenic fluid reaching the inner hull and the temperature distribution there. Simulation results using a computational fluid dynamics tool were compared with the experimental data for the leaked cryogenic fluid flow and evaporation in the secondary insulation layer. The experimental and computational results suggest that, unless there is a massive leak, the cryogenic fluid mostly evaporates in the insulation layer and does not reach the inner hull in the state of liquid.

• 한국수소및신에너지학회논문집
• /
• 제29권5호
• /
• pp.466-472
• /
• 2018

The investigation of cryogenic liquid pool spreading is an essential procedure to assess the hazard of cryogenic liquid usage. In this experimental study, to measure the evaporation velocity when the pool is spreading, liquid nitrogen was continuously released onto unconfined concrete ground. Almost all of the reported results are based on a non-spreading pool in which cryogenic liquid is instantaneously poured onto bounded ground for a very short period of time. A simultaneous measurement of the pool location using thermocouples and of the pool mass using a digital balance was carried out to measure the evaporation velocity and the pool radius. A greater release flow rate was found to result in a greater average evaporation velocity, and the evaporation velocity decreased with the spreading time and the pool radius.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권3호
• /
• pp.72-82
• /
• 2007

This paper relates to reducing the temperature of a cryogenic liquid by contacting it with gas bubbles, which can be characterized by diffusion-driven evaporative cooling, The characteristic of diffusion-driven evaporative cooling is thoroughly examined by theoretical. analytical and experimental methods specifically for the case of helium injection into liquid oxygen. The results reveal that if the gaseous oxygen partial pressure in helium bubbles is lower than the liquid oxygen vapor pressure, cooling occurs autonomously due to diffusion mass transfer. The method of lowering the injected helium temperature turns out to be very effective for cooling purpose.

• International Journal of Fluid Machinery and Systems
• /
• 제3권4호
• /
• pp.324-331
• /
• 2010

Cavitation in cryogenic fluids generates substantial thermal effects and strong variations in fluid properties, which in turn alter the cavity characteristics. In order to investigate the cavitation characteristics in cryogenic fluids, numerical simulations are conducted around an axisymmetric ogive in liquid nitrogen and hydrogen respectively. The modified Merkle cavitation model and energy equation which accounts for the influence of cavitation are used, and variable thermal properties of the fluid are updated with software. A good agreement between the numerical results and experimental data are obtained. The results show that vapor production in cavitation extracts the latent heat of evaporation from the surrounding liquid, which decreases the local temperature, and hence the local vapor pressure in the vicinity of cavity becomes lower. The cavitation characteristics in cryogenic fluids are obtained that the cavity seems frothy and the cavitation intense is lower. It is also found that when the fluid is operating close to its critical temperature, thermal effects of cavitation are more obviously in cryogenic fluids. The thermal effect on cavitation in liquid hydrogen is more distinctively compared with that in liquid nitrogen due to the changes of density ratio, vapour pressure gradient and other variable properties of the fluid.

• 한국가스학회지
• /
• 제2권3호
• /
• pp.37-48
• /
• 1998

밀폐된 초저온액화가스 저장탱크에 액화질소의 충전량을 바꾸어 가면서 시간이 경과함에 따른 탱크 내부의 여러 가지 변화에 대해 조사하였다. 탱크 내부의 압력, 온도, 액체와 기체의 비율 등의 변화는 충전된 액체의 양에 의존한다. 탱크에 충전된 액체의 양에 따라 (1)액면이 높아지면서 액화를 동반하기도 하고, (2)액면이 높아짐에도 불구하고 초기에는 액체의 기화가 일어나다가 압력이 높아지면 다시 액화가 일어나기도 하며, (3)액면은 일정하게 유지되지만 액체의 기화가 일어나기도 하며, (4)액면이 낮아짐과 동시에 액체의 기화가 일어나는 등 다양한 변화를 나타내었다. 탱크에 액체를 가득 채우면 압력이 급상승하여 매우 위험하므로 안전수칙에 따라 $90\%$ 이하 충전해야한다. 탱크가 완전히 밀폐되어 있을 경우, 탱크를 액체로 가득 채우면 불과 5일만에 80bar의 압력상승을 가져오지만, $90\%$ 충전하면 5일 동안에 겨우 1.5bar의 압력상승이 일어난다. 그러나 어느 경우이건 액체를 충전한 채 탱크를 완전히 밀폐시킨 뒤 장기간 방치하는 것은 대단히 위험하다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 학술대회
• /
• pp.308-315
• /
• 2008

극저온 유체를 운반하는 선박의 화물창은 보통 1차 방벽과 2차 방벽으로 구성되어 있다. 1차 방벽에 소량의 극저온 유체의 누출이 생기더라도, 액밀이 되는 2차 방벽에서 추가적인 극저온 유체의 누출을 방지할 수 있기 때문이다. 그러나 2차 방벽에 추가적인 손상이 생길 경우 유리솜으로 만들어진 Flat Joint를 거쳐 선체내벽까지 극저온 유체에 노출될 가능성이 있게 된다. 본 연구의 관심사는 2차 방벽의 손상 정도에 따라, 그리고 누출되는 극저온 유체의 양에 따라, 내측선체에 얼마나 영향이 미치는가를 알아보는 것이다. 이를 위해 본 연구에서는 극저온 유체를 운반하는 선박의 화물창을 구성하는 2차 방벽에 구멍을 뚫어 Flat Joint 사이로 극저온 유체가 흘러 들어가도록 격자를 생성한 후, CFD 소프트웨어를 이용하여 극저온 유체의 누출에 대한 계산을 수행 하였으며 이를 실험 결과와 비교 분석 하였다. 실험과 계산 결과를 살펴보면, 극저온 유체량에 따라 내측 선체에의 피해를 최소화 할 수 있음을 확인하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년 추계학술대회논문집
• /
• pp.308-315
• /
• 2008

극저온 유체를 운반하는 선박의 화물창은 보통 1차 방벽과 2차 방벽으로 구성되어 있다. 1차 방벽에 소량의 극저온 유체의 누출이 생기더라도, 액밀이 되는 2차 방벽에서 추가적인 극저온 유체의 누출을 방지할 수 있기 때문이다. 그러나 2차 방벽에 추가적인 손상이 생길 경우 유리솜으로 만들어진 Flat Joint를 거쳐 선체내벽까지 극저온 유체에 노출될 가능성이 있게 된다. 본 연구의 관심사는 2차 방벽의 손상 정도에 따라, 그리고 누출되는 극저온 유체의 양에 따라, 내측선체에 얼마나 영향이 미치는가를 알아보는 것이다. 이를 위해 본 연구에서는 극저온 유체를 운반하는 선박의 화물창을 구성하는 2차 방벽에 구멍을 뚫어 Flat Joint 사이로 극저온 유체가 흘러 들어가도록 격자를 생성한 후, CFD 소프트웨어를 이용하여 극저온 유체의 누출에 대한 계산을 수행 하였으며 이를 실험 결과와 비교 분석 하였다. 실험과 계산 결과를 살펴보면, 극저온 유체량에 따라 내측 선체에의 피해를 최소화 할 수 있음을 확인하였다.

• 한국전산유체공학회지
• /
• 제18권2호
• /
• pp.17-25
• /
• 2013

The process of flow through porous media is of interest a wide range of engineering fields and areas, and the importance of fluid flow with a change in phase arises from the fact that many industrial processes rely on these phenomena for materials process, energy transfer. Especially, the flow phenomena of cryogenic liquid subjected to evaporation is of interest to investigate how the cryogenic liquid behaves in the porous structure. In this study, thermo physical properties, morphological properties of the glass wool with different bulk densities in terms of its temperature-dependence and permeability behaviors under different applying pressure are discussed. Using the experimentally determined properties, characteristics of two main experimental results are investigated. In addition, simulation results are used to realize the cryogenic liquid's flow in porous media, and are compared with experimental results. By using the experimentally determined properties, more reasonable results can be suggested in dealing with porous media flow.

• 한국정밀공학회지
• /
• 제34권4호
• /
• pp.247-251
• /
• 2017

Titanium alloy has been widely used in the aerospace industry because of its high strength and good corrosion resistance. During cutting, the low thermal conductivity and high chemical reactivity of titanium generate a high cutting temperature and accelerates tool wear. To improve cutting tool life, cryogenic machining by using a liquid nitrogen (LN2) jet is suggested. In cryogenic jet cooling, evaporation of LN2 in the tank and transfer tube could cause pressure fluctuation and change the cooling rate. In this work, cooling uniformity is investigated in terms of liquid nitrogen jet pressure in cryogenic jet cooling during titanium alloy turning. Fluctuation of jet spraying pressure causes tool temperature to fluctuate. It is possible to suppress the fluctuation of the jet pressure and improve cooling by using a phase separator. Measuring tool temperature shows that consistent LN2 jet pressure improves cryogenic cooling uniformity.

• 한국초전도ㆍ저온공학회논문지
• /
• 제22권4호
• /
• pp.51-56
• /
• 2020

In order to increase thrust of the space launch vehicle, liquid oxygen as an oxidizer and kerosene or liquid hydrogen as a fuel are generally used. The oxidizer tank and fuel tanks are manufactured by composite materials such as CFRP (Carbon Fiber Reinforced Plastic) to increase pay load. The thermal stress of the cryogenic propellant tank should be considered because it has large temperature gradient. In this study, to confirm the design integrity of the oxidizer tank of liquid oxygen, a numerical analysis was conducted on the thermal stress and temperature distribution of the tank for various charging speed of the cryogenic fluid from 100 ~ 900 LPM taking into account the evaporation rate of the liquid nitrogen by convective heat transfer outside the tank and boiling heat transfer inside the tank. The thermal stress was also calculated coupled with the temperature distribution of the CFRP tank. Based on the analysis results, the charging speed of the LN2 can majorly affects the charging time and the resultant thermal stress.