• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.1
• /
• pp.103-108
• /
• 1999

Restoration of severly carious, malformed or traumatically fractured primary incisors is one of the most difficult challenges in restorative dental care for preschoolers. In restoring primary anterior teeth, four types of complete coverage crowns have been attempted over the years. Stainless steel crowns, open-faced stainless steel crowns, acid-etched crowns(strip crowns), and preformed polycarbonate crowns have been the choices. While these restorations have been acceptable for many patients, they all have very distinct limitations. The ideal full coronal restoration for a primary incisor requires durability, retention, and esthetics. This paper reported veneered stainless steel crown restoration of primary anterior teeth by silicoater technique. Veneered stainless steel crown restoration by silicoater technique is considered to be a durable, retentive, and esthetic restoration.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.292-300
• /
• 1995

According to the number of cold-rolled coils, the amount of roll wear and thermal expansion, and roll gap profile were calculated, by using the actual data from the finishing mill. Also, based on those data, the calculations of the deflection, the flattening, and the contact pressure of vwork rolls and backup rolls were made respectively. Specially, in the calculation of contact pressure, the numerical results were obtained not only during the normal rolling, but also during the abnormal rolling, by modeling mathematically the dynamic impact force which occurs when the head section of the strip is threading through rolls. With those results the growth of the fatigue region and the fatigue damage of rolls were predicted. Also the optimum roll-grinding depth was determined to maximize the roll life.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.1
• /
• pp.34-43
• /
• 1994

In order to improve thickness profile of cold rolled steel strip, a computer simulation and actual cold rolling experiments on a 4-high tandem cold mill were carried out. In this study, tapered barrel end at top work roll and incurved barrel body at bottom work roll were examined for reducing edge drop and threading of stripe. Also, the most effective stand of tandem cold mill and magnitude of optimal taper crown at several stand were investigated under a typical rolling condition. From actual rolling experiments, it was verified that thickness deviation over strip width could be improved up to 1.06% by applying tapered and incurved work roll only at the second and up to 0.89% by applying them at both the second and the third stand.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1068-1071
• /
• 1996

Good shape on flat rolled product is necessary to meet today's customer quality requirement. To meet the increasing demand in quality of strip shape from downstream customers, POSCO has replaced the Automatic Shape Control(ASC) system with the existing one that had used noncontact type measuring system at No.2 Cold Rolling Mill, Pohang works in October, 1995. The strip shape is influenced by the profile, roll crown, bending control, skew control system, as well as work roll cooling system. We have used ASC to adjust those factors in Cold Rolling Mill that could get a satisfactory result, almost less than .+-.5 1-unit deviation from the target shape. However, the downstream customer(i.e. Continuos Annealing Line) wants a good shape not only at the moment of exit of roll bite, but after rolling without tension. In this investigation, the difference will be discussed and how deal with this problem.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.10
• /
• pp.1062-1070
• /
• 2009

The strip shape for the stainless steel process has made an issue of the strip quality, and hence the shape control method is developed at the Sendzimir rolling mill (ZRM). ZRM is a stainless cold rolling mill and has actuators for the shape control. They are first intermediate rolls and top crown rolls, which are controlled horizontally and vertically, respectively. The shape control of the stainless steel rolling process has difficulty in obtaining the symmetrical shape. The objective of the shape control is to minimize the shape deviation and to maintain stable state, which keeps symmetrical shape pattern in the lateral direction. The method of the shape recognition employs a least squares method and neural network. The shape deviation is the difference between the target shape and actual shape and is controlled by the fuzzy shape control. The fuzzy shape control using operator's informative knowledge is proposed in this paper. The experiments are carried out online for various stainless materials and sizes. The productivity of the rolling process has increased from 9.0 to 9.4 tons per hour.

• Restorative Dentistry and Endodontics
• /
• v.39 no.3
• /
• pp.226-229
• /
• 2014

Orthodontic extrusion is usually performed by means of a fixed orthodontic appliance that utilizes arch wire attached to adjacent teeth and transfers the desired force by elastic from the wire to the root. However, clinicians often encounter cases where the bonding required for tooth traction is not possible because the adjacent teeth have been restored with ceramic or veneer. The purpose of this case report is to describe a modified orthodontic extrusion appliance that is useful when conventional orthodontic treatment is not possible. The modified appliance was fabricated using an artificial tooth, clear plastic sheeting, and a braided fiber-reinforced composite strip that covered adjacent teeth without bonding. It satisfied the esthetic and functional needs of the patient and established the optimal biologic width.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.142-146
• /
• 2001

In this study, it was investigated the influence of cold rolling factors on the edge drop. Edge drop was highly affected by the shape of work roll, the amount of work roll shift and the crown of hot strip, but the effect of bending force at the front stand was relatively small. The used numerical model was examined by comparing to the result of measured field data, and it showed a qualitative agreement with each other.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.3-9
• /
• 1999

The recent technical trend in hot rolling of steel can be described as process and product technologies which have been progressed with modern mill equipment and computers. Precise gauge and width control can be achieved by up-to-date control methods such as AGC and AWC systems. Roll benders and various shape control systems enabled high quality flatness and crown control. Mills can produce higher tensile materials by new process based on process metallurgy. The use of high speed steel rolls and on line roll grinders make the schedule free rolling easier which results in cost saving. Process itself goes toward continuous and simple flow type which has lower operation. Endless rolling and strip casting are examples of the trend. Materials with higher tensile strength and various functions have been developed in last years to meet the customer's needs and this trend will continue.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.24 no.4
• /
• pp.805-812
• /
• 1997

Despite dentistry's attempts to improve the dental health of the public and to minimize the effects of caries, many children still present with extensive destruction of primary anterior teeth. One of dentistry's most challenging tasks is to repair these teeth with restoration which are durable, retentive, and esthetic. Esthetic restoration can often be achieved with polycarbonate crowns, strip crowns, conventional S-S crowns, open-faced S-S crowns, commercially veneered S-S crowns. But, all of these have limitation. Advances in restorative materials and metal-bonding procedures have made possible new restorative techniques that combine the advantages of S-S crowns with the cosmetics of composite restoration methods. The described technique of bonding composite to trimmed and fitted S-S crowns offers many advantages over other techniques currently used to restore primary anterior teeth. 1. If S-S crowns are accurate trimmed and contoured, good retention of crowns is achieved. 2. The patient time required is similar to that of conventional S-S crowns. 3. Good esthetics and high bond strengths are achieved. 4. It is possible to use this veneering technique intraorally on crowns that have fractured veneers.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.11
• /
• pp.66-72
• /
• 2008

During the plate and foil cold rolling process, considerable values of the force of material pressure on the tool occur. These pressures cause the elastic deformation of the roll, thus changing the shape of the deformation legion. Rolled copper foils should be characterized by a good quality and light dimensional tolerances. Because of automation that is commonly implemented in flat product rolling mills, these products should meet the requirements of tightened tolerances, particularly strip thickness, and feature the greatest possible flatness. The shape of the roll gap is influenced by the elastic deformation of rolls parts of the rolling process affecter of the pressure force. However, to control roll deformation should be difficult. Because the foil thickness is very thin and the permissible deviations in the thickness of foil are small. In this paper, FE-simulation of roll deformation in thin foil cold roiling process is presented.