• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.3
• /
• pp.14-25
• /
• 1990

A model predicting thermal and wear crown in order to control strip crown and shape has been investigated at the hot roll mill. A basic equation of predicting wear crown was obtained experimentally whereas thermal crown was approximately analyzed by the integral method. The calculated result based on the accumulative model of basic eauation coincides with that measured under the real rolling conditions. The effect of wear corwn is also analyzed by the longitudinal feeding method of the work roll. The high frequency feeding method is recommended in removing local wear effectively.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.1
• /
• pp.64-75
• /
• 2019

The purpose of this study was to obtain instructions for size selection of prefabricated crown and tooth reduction by 3-dimensional analysis of the size and shape of the maxillary primary central and lateral incisors and prefabricated crowns (celluloid strip, resin veneered stainless steel, and zirconia crowns). The maxillary primary central and lateral incisors of 300 Korean children was scanned with three types of prefabricated crown to create standard three-dimensional tooth models and prefabricated crowns. The shapes of the prefabricated crowns and natural teeth were compared according to four parameters (mesio-distal width, height, labio-palatal width, and labial surface curvature coefficient) and calculated the amount of tooth reduction required for each prefabricated crown. The size 2 resin veneered stainless steel crown, size 1 zirconia crown, and size 2 celluloid strip crown were most similar in shape to the primary central incisor. The size 3 rein veneered stainless steel crown, size 2 zirconia crown, and size 3 celluloid strip crown were most similar to the primary lateral incisor. The amount of tooth reduction was similar in both maxillary primary central and lateral incisors. The incisal reduction was greatest for the zirconia crown. At the proximal surface, the zirconia and celluloid strip crowns required a similar amount of tooth reduction, but more than the resin veneered stainless steel crown. The labial surface reduction was greatest for the zirconia crown. The degree of lingual surface reduction was not significant among the three prefabricated crowns. Among the assessment parameters, mesio-distal crown width was the most important for choosing a prefabricated crown closest to the actual size of the natural crown.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.837-845
• /
• 1987

In the research of the rolling of strip, producing the strip with a close tolerance of thickness over the rolling direction was a principal object. But it was solved by the contribution of two-dimensional theory of rolling and the development of automatic gauge control system. And new requirements for the study of flatness, crown of rolled strip and edge drop grow up recently. These phenomena are closely related with the thickness distribution along the lateral direction of rolled strip. To analyse the thickness distribution of rolled strip along the lateral direction, elastic deformation of rolls and plastic deformation of work material must be discussed simultaneously. In this report, an approximate three-dimensional analysis based on Tozawa's three dimensional approach was applied to 12 cases of different rolling conditions and the numerical results were investigated. Especially stresses were laid upon the investigation of optimal boundary position between the three-dimensional analysis region and the plane strain analysis region.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.2
• /
• pp.327-333
• /
• 2003

Most of shape defects in steel strip are originated from the structure of rolling mill itself. For instance, strip crown occurs when the work roll is deformed by the bending moment induced on roll chocks. To get rids of the shape defects, it is necessary to increase the stiffness of rolling mill. The structure change of back-up roll is one of alternative ways to increase the mill stiffness without facility revamping from 4 high mill to 6 high mill. In this research work, the new back-up roll was developed and can be used in any type of 4 high mill to reduce the strip shape defects. The developed back-up roll consists of sleeve, arbor and phase angle adjusting system for arbor. The circumference of arbor is specially machined to adapt the strip width change during rolling. The experimental cold rolling test was done to prove the effectiveness of newly developed back-up roll. The experimental rolling results show that the new back-up roll has more powerful performance in reducing the shape defects than conventional back-up roll. It was also found that the new back-up roll has higher stability for shape control. In addition to, the only sleeve surface needs to be reground and changed in most cases, so that the maintenance cost can be greatly reduced.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1689-1699
• /
• 1990

Sendzimir rolling mill is widely used for rolling hard materials such as stainless steel due to its small work roll diameter and shape controllability using two effective actuators, AS-U-Roll crown adjustment and lst. intermediate roll shifting. However, in comparison with 4-high or 6-high mills, it is noteasy to get good strip or excellent flatness because Z-mill has small diameter of work rolls which are easily deformed by load. A new mathematical model based on the method of dividing roll and strip into multo-portions was used to develop strip profile prediction software. Using the developed software, several influencing factors related to rolled strip profile for Z-Mill were tested analytically and characterized for the effective shape control. The effects of adjusting shape control actuators of Z-Mill on strip profile were also examined and discussed in detail.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.512-517
• /
• 1993

The cold rolled strip meets continuously rising demands on the less deviation of thickness at the width direction of their rolled products. Especially, the special interest has been to find the methods to reduce the edge drop which influences seriously on the yield losses and the quality of the rolled products. In this study, the influence of hot coils on the thickness profile of cold rolled strip was analyzed. For obtainint the tapered work roll shig\ft conditions, the thermal crown and the flattening between the work roll and the strip were calculated, and the main parameters which have mostly effects on the edge drop were simulated. Also the obtained conditions from the simulation were applied to Tandem Cold Rolling Mill to investigate the change of the edge drop and the crown ratio depending on the amount of work roll taper and the length of contact of taper. The results of the application led to better thickness profile than conventional one.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.142-149
• /
• 1999

Strip profile and shape control is one of the most important technologies in cold mill, especially for ultra-thin and wide cold strip. The 6-high mills, both of HCMW and UCMW mill, are known to be very effective for the shape controllability. The optimized values of these factors for set-up scheduling were analyzed and found that excellent strip control would be possible by controlling the combination of the influencing factors according to hot coil profile. The important considerations for operation were discussed for individual stand.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.117-120
• /
• 2001

In hot roiling process, new rolling mills have been apapted to strip rolling but we can usually experience the problem of snaking of strip. This phenomenon was arisen by nonsymmetric rolling and on-centering and cambering of a strip and other mill conditions. Three dimensional analysis for strip rolling predicted the influence of nonsymmetric rolling, off-centering and pair crossing system This study evaluated the fundamental characteristics of snaking of a strip to optimize the operating condition for trouble free rolling.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.2
• /
• pp.240-247
• /
• 1999

Primary anterior teeth requiring extensive restorative therapy due to caries, trauma or developmental defects can present a particularly challenging problem for the pediatric dentist. The ideal restorative technique would combine strength, durability esthetics and efficiency in placement. Couple these concerns with the technical difficulties of operating on children with behavior management problems, and the dentist is left with the difficult task of choosing from a variety of restorative options. Restorative modalities currently in use to treat primary anterior teeth include bonding with composite resin as in celluloid strip crowns, conventional stainless steel crowns, open-faced stainless steel crowns, commercially and chairside veneered stainless steel crowns and epoxy-coated stainless steel crowns. Each of these techniques presents technical, functional or esthetic compromises that complicate their efficient and effective usage. This is a report of the results obtained at the Department of Pediatric Dentistry, College of Dentistry Seoul National University, through the use of these various methods of treating primary anterior teeth.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.3
• /
• pp.453-458
• /
• 2003

Usually Mylar strip and wedge or celluloid strip crown were used in conventional method of restoring proximal carious lesions of primary anterior teeth. But, these methods have some difficulties to place the matrix and wedge due to short crown lenth and interdental spacing of primary teeth. And it is difficult to form proper cavosurface margin due to the rigidity of matrix and inconvenience to support matrix by practitioner's hand in narrow oral cavity of child. This article describes an alternative technique for restoring carious lesions of primary anterior teeth using available straw. This method is very convenient and reduce chair time and it also allows good marginal adaptation.