• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1199-1213
• /
• 2011

Slurry type shield would be very effective for the tunnelling in a sandy ground, but low slurry pressure could cause a tunnel face failure or a ground settlement in front of the tunnel face. Thus, the stability of tunnel face could be maintained by applying an excess slurry pressure that is larger than the active earth pressure. However, the slurry pressure should increase properly because an excessively high slurry pressure could cause the slurry flow out or the passive failure of the frontal ground. It is possible to apply the high slurry pressure without passive failure if a horizontal impermeable layer is located in the ground in front of the tunnel face, but its location, size, and effects are not clearly known yet. In this research, two-dimensional model tests were carried out in order to find out the effect of a horizontal impermeable layer for the slurry shield tunnelling in a saturated sandy ground. As results, larger slurry pressure could be applied to increase the stability of the tunnel face when the impermeable layer was located in the ground above the crown in front of the tunnel face. The most effective length of the impermeable grouting layer was 1.0~1.5D, and the location was 1.0D above the crown level. The safety factor could be suggested as the ratio of the maximum slurry pressure to the active earth pressure at the tunnel face. It could also be suggested that the slurry pressure in the magnitude of 3.5~4.0 times larger than the active earth pressure at the initial tunnel face could be applied if the impermeable layer was constructed at the optimal location.

• Weed & Turfgrass Science
• /
• v.2 no.1
• /
• pp.23-29
• /
• 2013

This study was conducted to clarify effects of weed control methods on damages from agricultural chemicals of pear trees, growth of weeds and states of pear trees after treating pear orchards with different methods of weed controlling, density of GLU and application times. The growth and occupation rate were investigated after 10, 20 and 40 days of weeding treatment. According to a result of the first treatment conducted when weeds in the lower parts of crown in a pear orchard began to grow and grew about 20 cm, unwoven cloth covering showed the highest control value with 100% in all 14 kinds of grasses. In comparison, Stellaria aquatica and catchweed bedstraw showed 96.7% and 97.3% respectively in the 20 DAT investigate after the first treatment of GLU 540 g a.i. ha-1 and the high control value of 100% in other all kinds of grasses. According to an investigation of stalk enlargement, length of new shoot and the number of new shoot made to know differences in tree growth following treatment of the lower part of crown, to use weed killers two or three times a year or to eliminate grasses with machines have positive effects on cross growth of pear trees.

• Journal of Korean Society of Forest Science
• /
• v.64 no.1
• /
• pp.1-10
• /
• 1984

Two fast-growing clones 65-29-19 and 66-6-8 and two less fast-growing clones 66-14-29 and 66-14-99 were compared at intensively cultured plots to identify what morphological characters are related to fast growth and high biomass yield of Populus alba ${\times}$ Populus glandulosa $F_1$. The plantations were established in the spring of 1982 and 1983 at the Seoul National University nursery in Suweon. Differences in dry matter production were found among two-year-old clones but not, among one-year-old clones. Highly significant correlations were found between total leaf area per tree and total dry weight per tree and between total branch length per tree and total dry weight per tree for two-year-old clones. This relation was more obvious during the late growing season. Morphological characters desirable for producing high biomass identified in fast-growing clones were as follows; high shoot-root ratio, high leaf surface area per tree, long leaf retention period, and many small leaves and compact crown architecture in the upper portion of true crown.

• The Journal of Korean Academy of Prosthodontics
• /
• v.56 no.1
• /
• pp.40-49
• /
• 2018

It is reported that the causes of unaesthetic proportion of anterior teeth vary widely. Especially, when the unaesthetic tooth proportion of the mandibular incisors arises due to the wear of the anterior teeth accompanied by the compensation of the alveolar bone, it may cause serious functional and aesthetic problems. In such case, it should be considered that the evaluation of vertical dimension and tooth proportion as well as smile line, soft tissue and hard tissue morphology. And, increase of vertical dimension or clinical crown lengthening followed by prosthodontic restorations is needed to improve the interdental mesial/distal, width/length ratio considering the anterior guidance. This case report demonstrates functional and aesthetic improvements through systematic diagnosis and treatment procedures in a 48-year-old male patient with unaesthetic anterior teeth proportion because of tooth wear accompanied by the compensation of alveolar bone and defect of several central incisors due to chronic periodontitis.

• Journal of Oral Medicine and Pain
• /
• v.39 no.2
• /
• pp.69-77
• /
• 2014

Purpose: It aims to verify the applicability of existing age estimation methods derived from data of foreign population groups to Korean population groups. Moreover it is to suggest a new way applicable to practical age estimation on the basis of newly calculated regression formulae from data of Korean population groups and develop a subsidiarily applicable method to the existing method. Methods: Ratio of pulp cavity to dental crown was calculated by measuring the height and width of dental crowns and pulp cavities at the cervical line from 4,034 first and second upper molars, first and second upper premolars, first and second lower molars and first and second lower premolars on both left and right sides of 400 patients who had been treated in Dental Hospital of Yonsei University College of Dentistry, and regression equations were derived from the values of the ratio. Results: The equation with correlation coefficients the highest among females was as follows: age=$107.96-75.684{\times}{\sharp}17$ TCHI-$53.741{\times}{\sharp}26$ TCVI-$40.664{\times}{\sharp}45$ TCVI-$56.307{\times}{\sharp}46$ TCVI. Randomized anohter Korean female subjects (n=20) are applicated to the new equation. Mean of error of estimate is 10.322 years, standard deviation is 12.852 years. Minimum of error of estimate is 1.018 years, maximum is 21.365 years Conclusions: The error range of age estimation was found to be slightly wider when the existing regression formulae of Drusini were applied to Korean population groups. Also age estimation in females using the ratio of pulp cavity to dental crown measured with the length and width of dental crowns and pulp cavities from maxillomandibular molars was observed to have the highest reliability in the research. However, we consider that advanced equations of regression are needed to apply to both molars and premolars of males and females in the future.

• Journal of Periodontal and Implant Science
• /
• v.34 no.4
• /
• pp.819-836
• /
• 2004

Nowdays, the awareness of implant treatment has grown rapidly among dentists and patients alike in Korea, as it becomes a widely accepted treatment. The reason is that unlike crown and bridge or denture treatment, implant treatment helps preserve existing bone and improve masticatory functions. So, It is needed understanding about the type, distribution of implant patient. The following results on patient type and implant distribution were compiled from 4433 implant cases of 1596 patients treated at the periodontal dept. of Y University Hospital during 1992 to 2004. 1. There are no dissimilarities between men and women, with patients in their 40, 50s accounting for 52.5% of patients and 57.5% of implant treatments; the largest share of patients and implant treatments. 2. Mn. posterior area accounted for 54.9% of implant treatments followed by Mx. posterior area(27.6%), Mx anterior area(11.9%) and Mn anterior area(5.6%). 3. Partial edentulous patients treated by single crown and bridge-type prosthesis accounted for 97.5% and fully edentulous patient accounted for the remaining 2.5%. 4. The major cause of tooth loss is periodontal disease, followed by dental caries, trauma and congenital missing. Also, older people are more likely to suffer from tooth loss due to periodontal disease rather than dental caries. 5. In the distribution of bone quality for maxillae, type III was most, followed by type II, r type IV and r type I. As for mandible, type II was most, followed by type III, type IV and for type I. 6. In the distribution of bone quantity for maxillae, type C was most, followed by type B, type D, type A, and for type E. As for mandible, type B was 52% most, followed by type C, type D, type A and type E. 7. The majority of implants were those of 1O-14mm in length (85.2%) and regular diameter in width (64%). The results provided us with basic data on patient type, implant distribution, bone condition, etc. We wish that our results coupled with other research data helps assist in the further study for better implant success/survival rates, etc.

• Journal of Periodontal and Implant Science
• /
• v.32 no.3
• /
• pp.539-554
• /
• 2002

It has been approximately 40 years since $Br{{\aa}}nemark$ first introduced osseo-integration for implants in the early 1960s. Unlike crown and bridge or denture treatment, implant treatment helps preserve existing bone and improve masticatory functions. Thus, the awareness of implant treatment has grown rapidly among dentists and patients alike in Korea, as it becomes a widely accepted treatment. The following results on patients type and implant distribution were compiled from 1814 implant cases of 640 patients treated at the periodontal dept. of Y University Hospital during 1992 to 2001. 1. There are no dissimilarities between men and women, with patients in their 40,50s accounting for 49% of patients and 56% of implant treatments; the largest share of patients and implant treatments. 2. Mn. posterior area accounted for 59% of implant treatments followed by Mx. posterior area(21%), Mx anterior area(l4%) and Mn anterior area 2%. 3. Partial edentulous patients treated by single crown and bridge-type prosthesis accounted for 98% and fully edentulous patient accounted for the remaining 2% 4. The major cause of tooth loss is periodontal disease, followed by dental caries, trauma and congenital missing. Compared to women, men are more likely to suffer from tooth loss due to periodontal disease. Also, older people are more likely to suffer from tooth loss due to periodontal disease rather than dental caries. 5. The distribution of bone quality for maxillae was 52% for type III, followed by 23% for type II, 20% for type IV and 0% for type I. As for mandible, the distribution was 52% for type II, followed by 37% for type III, 7% for type IV and 4% for type I. 6. The distribution of bone quantity for maxillae was 49% for type C, followed by 34% for type B, 14% for type D, 3% for type A, and 0% for type E. As for mandible, the distribution was 52% for type B, followed by 35% for type C, 6% for type D, 3% for type A and 0% for type E. 7. The majority of implants were those of 10-14mm in length (80%) and regular diameter in width (79%). The results provided us with basic data on patient type, implant distribution, bone condition, etc. We wish that our results coupled with other research data helps assist in the further study for better implant success/survival rates, etc.

• Analytical Science and Technology
• /
• v.6 no.1
• /
• pp.9-19
• /
• 1993

Fatty acid salts derived from soap can be transferred into a typical derivative with p-bromophenacyl bromide using crown ether, a catalizer by the solid-liquid phase transfer reaction in nonpolar, aprotic solvents and separated by the reverse phase high performance liquid Chromatography (RP-HPLC) and determined using UV detector. The minimal limit of detection was defined at approximately 10~50ng in accordance with the chain length. The derivatization reaction in the presence of EDTA can be applied mot only to the calcium salts but also to the other various metal salts. The recoveries of fatty acid derivatizations in the absence and presence of the midium containing the yeast extract were obtained $95.4{\pm}1.2$, and $85.2{\pm}2.4%$ respectively. The analytical method would be applicable to determine the biodegradation of fatty acid salts in nature as well as in artificial condition such as shaker flask-medium method.

• Journal of Periodontal and Implant Science
• /
• v.36 no.3
• /
• pp.661-671
• /
• 2006

The purpose of this study was to evaluate cumulative survival rate (CSR, %) of mandibular posterior single tooth implants replaced with ITI SLA (sand-blasted, large-grit, acid-etched) implant system and compare the CSR between first and second molar. The findings from the results were as follows; 1. Total of 158 implants were inserted into 147 patients. 68 patients were males, 79 patients were females and their mean age was 47.8 years. 98 implants were placed in first molar area and 60 implants were placed in second molar area. In terms of diameter, implants with wide diameter over 4.8mm dominated (91.1%). Implants with length over lOmm were used (96.2%). 2, In the two cases, there was a slight transient numbness which recovered within 1-2 months. Nine SynOcta screw type abutments demonstrated screw loosening, There were ten cases of crown fallen-out from decementation. 3. Only one failed out of 158 implants. The CSR was 99.4%. The CSRs for first molar and second molar were 99% and 100%, respectively. From the results, it was concluded that single tooth replacement implant in the mandibular posterior area, might be considered as the effective treatment modality comparable to the conventional crown and bridge.

• Journal of Korean Society of Forest Science
• /
• v.88 no.3
• /
• pp.389-399
• /
• 1999

This study was conducted to develop an application software, SIDAS3D(Stand Inventory Data Analysis System for 3 Dimensional Representation), of which the purpose of development is to make it easier to analyze and display the 3D spatial structure of a forest stand, based on the data such as tree position, species, DBH, height, clear length of individual trees, and crown width. This program has a statistical analysis function for stand attributes per hectare and displays simple graphs of stand statistics such as the distribution of diameters, heights, and volumes. It also has two additional functions, of which one is to display the 3D image of stand structure and the other is to display the image of crown projection. In addition, this program provides an imaginary treatment simulation function, which can visually confirm the suitability of silvicultural treatments on computers. To test the precision and reliability of SIDAS3D, data obtained by the precision forest inventory method were used. Statistical analysis ability of SIDAS3D was compared with that of SAS. And its representational ability was compared with that of TreeDraw. According to the verification, SIDAS3D was superior to SAS and TreeDraw in both the data processing time and the interpretative ability of results. It was concluded that SIDAS3D could be used to help users efficiently make decisions for appropriate silvicultural treatments and rational management plans because it has analysis functions providing various valuable information.