• 한국가스학회지
• /
• 제15권2호
• /
• pp.9-14
• /
• 2011

CNG 저장용기 재료인 SA-372 강에 대해 수소취화 영향을 조사하기 위한 시험을 수행하였으며 대기조건과 불활성 가스인 아르곤 그리고 CNG, HCNG 및 수소가스에 대해 35 MPa로 가압된 가스분위기에서 인장시험이 이루어 졌다. 또한 인장시험 속도는 4*10^-4 /s와 4*10^-5/s로 각각 설정하였다. 분위기 가스를 고압으로 유지한 상태에서 시험하기 위해 가압형 오토크레이버가 장착된 인장시험기를 사용하였다. 시험 결과 불활성 가스와 CNG 분위기에서는 대기조건의 인장강도, 연신률 및 단면수축률과 거의 유사한 특성을 보였으며 인장속도의 변화에 대해서도 큰 차이가 없는 것으로 나타났다. 그러나 30% 수소가 혼합된 수소혼합가스와 100% 수소 조건에서 인장강도는 큰 차이를 나타나지 않았지만 연신율과 단면 수축률에서는 눈에 띄는 변화가 있었다. 이로부터 수소가스의 취화효과는 수소가 포함된 조건에서 확인할 수 있었으며 수소농도가 높을수록 연신율과 단면수축률 변화가 크게 나타났다. 또한 인장 속도가 느릴수록 수소취화가 더 많이 나타나는 것으로 확인되었다.

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2396-2403
• /
• 1994

An experimental study on material characterization and mechanical properties of SMC(Sheet Molding Compounds) compression method parts was carried out. Simple compression test using grease oil as a lubricant was carried out to characterize flow stress of SMC at elevated temperatures. Two different mold temperatures, $130^{\circ}C{\;}and{\;}150^{\circ}C$ and two different mold speeds, 15, 45 mm/min were used for preparing the specimen of SMC compression molded parts. Surface roughness, tensile, and 3-point bending tests were used to determine the effects of molding temperatures and speeds on mechanical properties of compression molded SMC parts. Orientation and distribution of glass fiber in the compression molded SMC parts were also investigated by photographing the burnt flat specimen and taking SEM(Scanning Electron Microscope) of cross-sectional T-specimen.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.256-259
• /
• 2004

In the present study, AZ31B sheets has a bad formability in room temperature, but the formability is improved significantly as increasing the temperature because of rolled magnesium alloy sheet has a hexagonal closed packed structure (HCP) and a plastic anisotropy. In this paper, after tensile test in various temperatures, strain rate, show the tensile mechanical properties, yield and ultimate strength, K-value, work hardening exponent(n), strain rate sensitivity(m). As temperature increased, yield, ultimate strength and K-value, work hardening exponent(n) are decreased but strain rate sensitivity(m) is increased. As cross-head-speed increased, yield, ultimate strength and K-value, work hardening exponent(n) are increased. And according to the temperature, how change the plastic anisotropy factor R. In addition, we observed how temperatures and cross-head-speed effect on microstructure.

• Journal of Mechanical Science and Technology
• /
• 제17권8호
• /
• pp.1113-1119
• /
• 2003

Experimental and numerical analyses were performed to characterize the fatigue behavior of spot welded joints in suspension mounting of a passenger car body. Static and fatigue tests were carried out for the tensile-shear and cross-tension specimens. S-N curve and fatigue strengths were obtained from the fatigue test of various specimens. Nonlinear finite element analysis showed that fatigue behavior of spot welded joints could be well estimated in terms of Von Mises stress at the nugget edge. Fatigue behavior of spot welded joint was represented by Von Mises stress better than the fatigue load.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.309-312
• /
• 2001

FEM simulating system of the cross-rolling texture formation offers a systematic and efficient way of exploring the relationship between the process variables and the state of plastic anisotropy of sheet product. Cross-rolled sheets possess higher average plastic strain ratios and lower planer anisotropy than those of the straight-rolled sheets. The employed model is a finite-element polycrystal model which each element used in FEM is assumed to be a crystal having different orientation by Takahashi. Texture development, deformation textures due to cross-rolling are predicted for face-centered cubic sheet metal. Crystal orientations are assigned on the basis of the pole figures obtained by X-ray diffraction. Development of anisotropy during cross rolling of an fcc sheet material is predicted theoretically with respected to flow stress and R-value in tensile test.

• Transactions on Electrical and Electronic Materials
• /
• 제10권1호
• /
• pp.9-15
• /
• 2009

There is a growing demand for a high voltage silicone rubber composite with high mechanical property and high electrical property. The effect of modified cross-linking agent on the mechanical, electrical properties, and short-circuit test performance of silicone rubber insulators have been investigated. To use base polymer, the various silicone polymers were prepared by the equilibrium polymerization. Aluminum trihydrate surface was treated by vinyl silane. Liquid silicone rubber nanocomposite was prepared from the compounding of VPMPS, HPDMS, catalyst, and alumina trihydrate modified with 1,3,5-trivinyl-l,3,5-trimethylcyclotrisiloxane. The mechanical property and electrical property for insulation materials were measured, indicating the high tensile strength and the good short-circuit property.

• 한국기계가공학회지
• /
• 제21권6호
• /
• pp.60-66
• /
• 2022

The optimal strain energy function was obtained by comparing the results of the analysis using the strain energy functions obtained by uniaxial tensile and equibiaxial tensile tests on gasket materials used in hydrogen fuel cells, with the results measured using a contact pressure measurement sensor. At this time, even when only the uniaxial tensile test was conducted, Yeoh could obtain the most accurate results even by conducting only the uniaxial tensile test. Using this, an analysis of the cross section of the gasket used in stack confirmed a safe contact pressure and no deformation on the separator. In the future, research will be conducted to verify the gasket durability by reliability evaluation.

• 열처리공학회지
• /
• 제31권6호
• /
• pp.307-314
• /
• 2018

Simple tensile tests and microstructural investigations have been performed on extrudates of high strength aluminum alloys such as 7075, 7021 and 7xxx(Sc) to understand correlation between extruding conditions and extruded properties. Tensile specimens which were taken from different locations at the same cross section of an extrudate were tested at room temperature and with a strain rate of $8.9{\times}10^{-5}/s$. The microstructures according to the locations at the cross section have been observed using optical microscopy and electron back-scattered diffraction (EBSD) mapping to characterize the effect on stress-strain curve. The results could be classified in three types independent of alloying contents and extusion methods. The fine differences in the stress-strain curves were resulted from inhomogenity in the microstructures according to locations of an extrudate which were performed through instantaneous extruding conditions such as temperature, strain rate and strain.

• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.50-58
• /
• 2008

The SM45C metallic coupons have been tested under static tensile loading with acoustic emission (AE) as the load-deflection curve mainly. In this study, we used AE to detect the yielding of material and AE techniques was applied to rapidly estimate the mechanical characteristics of a material. First, coupons without an artificial defect were tested at different cross-head speed. For all cases in this analysis, yielding point of SM45C coupons did not appear definitely compared to mild steel, whereas coupons start to generate AE counts upon yielding. So all cases are normalized to know the possibility of accelerated life test of a material. And next, coupons with different from sizes of circular hole defects were tested at the same cross-head speed of 5 mm/min. Results were classified into 3 classes and analyzed by AE amplitude & signal strength as a function of time. Summarizing the specific conclusions, we need to additional research considering plate with width-ratio in order to estimate the fracture mechanism.

• Journal of the Korean Wood Science and Technology
• /
• 제36권2호
• /
• pp.20-28
• /
• 2008

This study was carried out to provide the so-called circumferential slicing method for investigating radial distributions of the tangential strains and of moisture contents within the log cross section (LC) of Kalopanax pictus during indoor drying it. While the heartwood showed an almost uniform moisture content distribution in the range of about 50~55% in case of the green wood, it has gradually decreased toward the outer side, showing about 19% of moisture content difference from the innermost slice. Although the moisture gradient along the radial direction has gradually become gentle as drying progresses, the sapwood of the outer side represented the moisture contents below the fiber saturation point after 24 hours of drying while the heartwood in the inner part showed the moisture contents higher than the fiber saturation point. The pith side was laid under the tensile stress after 24 hours of drying, and then gradually decreasing toward the bark side, and showed the distribution being switched again to the tensile stress on the bark side. As the drying has progressed, this trend got more intensified, and finally showed the U-shaped distribution model after 48 hours of drying. The circumferential slice test is considered to be suitable in quantitatively determining the tangential strains and moisture content within a LC.