• Progress in Superconductivity and Cryogenics
• /
• v.25 no.4
• /
• pp.5-9
• /
• 2023

Lee, Kim, et al. reported in July 2023 that a modified lead apatite material, Pb_10-xCu_x(PO₄)₆O (0.9 < x < 1.1), exhibited superconductivity at room temperature and atmospheric pressure [1, 2]. However, their X-ray diffraction data clearly showed the presence of impurity phases, including Cu₂S, raising uncertainty about the sample quality. Subsequent studies have been conducted; however, different samples exhibited various physical properties. To verify the recipe for the sample growth process, we synthesized samples following the methodology outlined in the reference [1, 2]. An analysis of the structure and physical properties of the synthesized sample reaffirms the critical importance of high-quality sample growth.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3775-3786
• /
• 2023

Mixing Vane Grid (MVG) is one of the most important structures in fuel assembly due to its high performance in mixing the coolant and ultimately increasing Critical Heat Flux (CHF), which avoids the temperature rising suddenly of fuel rods. To evaluate the mixing performance of the MVG, a Total Diffusion Coefficient (TDC) mixing coefficient is defined in the subchannel analysis code. Conventionally, the TDC of the spacer grid is obtained from the combination of experiments and subchannel analysis. However, the processing of obtaining and determine a reasonable TDC is much challenging, it is affected by boundary conditions and MVG geometries. In is difficult to perform all the large and costing rod bundle tests. In this paper, the CFD method was applied in TDC analysis. A typical 5 × 5 MVG was simulated and validated to estimate the mixing performance of the MVG. The subchannel code was used to calculate the TDC. Firstly, the CFD method was validated from the aspect of pressure drop and lateral temperature distribution in the subchannels. Then the effect of boundary conditions including the inlet temperature, inlet velocities, heat flux ratio between hot and cold rods and the arrangement of hot and cold rods on MVG mixing and TDC were studied. The geometric effects on mixing are also carried out in this paper. The effect of vane pattern on mixing was investigated to determine which one is the best to represent the grid's mixing performance.

• Korea Trade Review
• /
• v.46 no.6
• /
• pp.73-92
• /
• 2021

Small and medium-sized enterprises (SMEs) account for a large proportion of the total number of enterprises in many countries. The development of SMEs has contributed to job creation and economic benefits. Every government has formulated active diversification strategies to promote the export market of SMEs, but the performance of export capabilities remains insufficient. The primary purpose of this study is to examine the effectiveness of export credit insurance in promoting SME export performance in Canada. Using data from 2008-2017, the augmented Dickey-Fuller (ADF) model to test the stationarity of the concerned variables and the error correction model (ECM) and autoregressive distributed lag (ARDL) cointegration test to empirically investigate the cointegration relationship between the research targets. The results represent the positive and critical impact of export relative price and domestic demand pressure on Canada's export performance, and the negative impact of the export volume index at a significant level. Regrettably, the impact of export credit insurance on the export performance of Canadian SMEs is considered exaggerated overall. In view of this result, it is necessary for the Canadian government to enact policies based on the current market status. And enhance confidence among SMEs to begin exports and diversify their markets rather than focusing only on the domestic or US market, especially given the impact of COVID-19. From the case of Canada, Korean government can attempt to learn from them to conduct more efficient strategies for SMEs.

• Membrane and Water Treatment
• /
• v.15 no.2
• /
• pp.59-66
• /
• 2024

This study evaluated the performance of a membrane aerated biofilm reactor (MABR) for nitrogen removal from a high-strength ammonia nitrogen-containing wastewater. The experimental setup consisted of four compartments that are sequentially anaerobic and aerobic to achieve complete nitrogen removal. The last compartment of the reactor setup contained a membrane bioreactor (MBR) to reduce sludge production in the system and to obtain a better-quality effluent. Continuous experiment over a period of 47 days showed that MABR exhibited excellent NH₄⁺-N removal efficiency (99.5%) compared to the control setup without MABR (56.5%). The final effluent NH₄⁺-N concentration obtained in the MABR was 2.99±1.56 mg/L. In contrast to NH₄⁺-N removal, comparable TOC removal values in the MABR and the control reactor (99.2% and 99.3%, respectively) showed that air supply through MABR is much more critical for denitrification than for organic removal. Further study to understand the effect of air supply rate and holding pressure on NH₄⁺-N removal in MABR revealed that an increase in both these parameters positively impacted reactor performance. These parameters are related to oxygen supply to the biofilm formed over the membrane surface, which in turn influenced NH₄⁺-N removal in MABR. Among the two different strategies to control biofilm over the membrane surface, results showed that scouring for a duration of 10 min on a weekly basis, along with mixing air supply, could be an effective method.

• Journal of Korean Society of Disaster and Security
• /
• v.12 no.4
• /
• pp.1-13
• /
• 2019

Recently, as the occurrence frequency of sudden floods due to climate change increased, it is necessary to install the facilities that can cope with the initial stormwater. Most researches have been conducted on the design of facilities applying the Low Impact Development (LID) and the reduction effect on rainfall runoff to examine with 1D or 2D numerical models. However, the studies on the examination about flow characteristics and stability of pipe network systems were relatively insufficient in the literature. In this study, the stability of the pipe network system in rainwater storage tank was examined by using 3D numerical model, FLOW-3D. The changes of velocity and dynamic pressure were examined according to the number of rainwater storage tank and compared with the design criteria to derive the optimal design plan for a rainwater storage tank. As a results of numerical simulation with the design values in the previous study, it was confirmed that the velocity became increased as the number of rainwater storage tank increased. And magnitude of the velocity in pipes was formed within the design criteria. However, the velocity in the additional rainwater storage pipe was about 3.44 m/s exceeding the allowable range of the design criteria, when three or more additional rainwater storage tanks were installed. In the case of turbulence intensity and bottom shear stress, the bottom shear stress was larger than the critical shear stress as the additional rainwater storage was increased. So, the deposition of sediment was unlikely to occur, but it should be considered that the floc was formed by the reduction of the turbulence intensity. In addition, the dynamic pressure was also satisfied with the design criteria when the results were compared with the allowable internal pressure of the pipes generally used in the design of rainwater storage tank. Based on these results, it was suitable to install up to two additional rainwater storage tanks because the drainage becomes well when increasing of the number of storage tank and the velocity in the pipe becomes faster to be vulnerable to damage the pipe. However, this study has a assumption about the specifications of the rainwater storage tanks and the inflow of stormwater and has a limitation such that deriving the suitable rainwater storage tank design by simply adding the storage tank. Therefore, the various storage tank types and stormwater inflow scenarios will be asked to derive more efficient design plans in the future.

• Tuberculosis and Respiratory Diseases
• /
• v.52 no.3
• /
• pp.251-259
• /
• 2002

Background : Reduced lung compliance and increased lung resistance are the primary lung mechanical abnormalities in acute respiratory distress syndrome (ARDS). Although there is little information regarding the mechanisms responsible for the increases in the respiratory resistance of ARDS, bronchodilators have been frequently administered in mechanically ventilated ARDS patients. To determine the effect of a bronchodilator on the respiratory mechanics depending on the level of applied positive end-expiratory pressure (PEEP), the changes in the respiratory mechanics by salbutamol inhalation was measured under the variable PEEP level in patients with ARDS. Materials and Methods : Fifteen mechanically ventilated paralyzed ARDS patients (14 of male, mean age 57 years) were enrolled in this study. The respiratory system compliance, and the maximum and minimum inspiratory resistance were obtained by the end-inspiratory occlusion method during constant flow inflation using the CP-100 pulmonary monitor (Bicore, Irvine, CA, USA). The measurements were performed at randomly applied 8, 10 and 12 cm $H_2O$ PEEP before and 30 mins after administrating salbutamol using a meter-dose-inhaler (100ug${\times}$6). Results : 1) The maximum inspiratory resistance of the lung was higher than the reported normal values due to an increase in the minimal inspiratory resistance & additional resistance. 2) The maximum inspiratory resistance and peak airway pressure were significantly higher at 12cm $H_2O$ of PEEP compared with those at 10cm $H_2O$ of PEEP. 3) Salbutamol induced a significant decrease in the maximum and the minimum inspiratory resistance but no significant change in the additional resistance only was observed at 12cm $H_2O$ of PEEP(from $15.66{\pm}1.99$ to $13.54{\pm}2.41$, from $10.24{\pm}2.98$ to $8.04{\pm}2.34$, and from $5.42{\pm}3.41$ to $5.50{\pm}3.58cm$ $H_2O$/L/sec, respectively). 4)The lung compliance did not change at the applied PEEP and salbutamol inhalation levels. Conclusion : The bronchodilator response would be different depending on the level of applied PEEP despite the increased respiratory resistance in patients with ARDS.

• Journal of the Korean earth science society
• /
• v.32 no.4
• /
• pp.388-401
• /
• 2011

Asian dust was observed a total of 66 times in the springtime during the period from 2002 to 2010, with 26 cases in March, 23 cases in April and 17 cases in May. This study investigates a Asian dust episode that occurred during the period from 22 to 25 May 2010, based on synoptic weather patterns, wind vector at 850 hPa, relative humidity at 1000 hPa, Jet streams and wind vector at 300 hPa, PM10 concentration in Korea and satellite imagery. In this case, Asian dust originated on 22 May along the rear of a developing low pressure system in Mongolia. The Asian dust was then transported southeastward and bypassed the Korea peninsula from 23 to 24 May, before reaching Japan on 25 May. Jet streams on 24 May bypassed the Korean peninsula and induced the development of a surface low pressure centered over the peninsula. The resulting air flow was critical to the trajectory of the Asian dust, which likewise bypassed the Korean peninsula. 72-hour backward trajectory data reveal that the Shandong Peninsula and the East China Sea were the points of origin for the air flows that swept through the Japanese sites where Asian dust was observable to the naked eay. The Asian dust pathway is ascertained by horizontal distribution of the Asian dust of RGB imagery from MODIS satellites which captured the Asian dust moving over the Shandong Peninsula, the East China Sea, and northwest of the Kyushu region in Japan. Since the synoptic pattern and the transport way of the Asian dust case are far from typical ones, which Asian dust forecasting technique has long been based on, this study can be good example of exceptional Asian dust pattern and it will be used for more accurate Asian dust forecasting.

• Journal of Embryo Transfer
• /
• v.27 no.2
• /
• pp.107-111
• /
• 2012

Miniature pig sperm cryopreservation is continually researched in biotechnology for breed conservation and reproduction. It is important to control the temperature at each stage of cryopreservation and cryoprotectant. It is also necessary to find the optimal cryoprotectant concentration and chemical elements of the extender. Recently, many studies have used various cryoprotectant materials, such as dimethyl sulphoxide (DMSO), ethylene glycol (EG), antifreeze protein (AFP), amides, and glycerol. Glycerol is a commonly used cryoprotectant. However, glycerol has critical cytotoxic properties, including osmotic pressure and it can cause irreversible damage to live cells. Therefore, We focused on membrane fluidity modifications can reduce cell damage from freezing and thawing procedures and evaluated on the positive effects of trehalose to the viability, chromatin integrity, and motility of boar sperm. Miniature pig sperm was separated from semen by washing with modified- Modena B (mMB) extender. After centrifugation, the pellet was diluted with the prepared first extender. This experiment was designed to compare the effects that sperm cryopreservation using two different extenders has on sperm chromatin. The control group used the glycerol only and it was compared with the glycerol and glycerol plus trehalose extender. Sperm viability and motility were evaluated using WST1 assays and computer-assisted semen assays (CASA). Chromatin structure was examined using acridine orange staining. For the motility descriptors, trehalose caused a significant (p<0.01) increase in total motility ($57.80{\pm}4.60%$ in glycerol vs. $75.50{\pm}6.14%$ in glycerol + trehalose) and progressive ($51.20{\pm}5.45%$ in glycerol vs. $70.74{\pm}8.06%$ in glycerol + trehalose). A significant (p<0.05) increase in VAP ($42.70{\pm}5.73{\mu}m/s$ vs. $59.65{\pm}9.47{\mu}m/s$), VSL ($23.06{\pm}3.27{\mu}m/s$ vs. $34.60{\pm}6.58{\mu}m/s$), VCL ($75.36{\pm}11.36{\mu}m/s$ vs. $99.55{\pm}12.91{\mu}m/s$), STR ($54.4{\pm}2.19%$ vs. $58.0{\pm}1.63%$), and LIN ($32.2{\pm}2.05%$ vs. $36.0{\pm}2.45%$) were also detected, respectively. The sperm DNA fragmentation index was 48.8% to glycerol only and 30.6% to glycerol plus trehalose. Trehalose added group showed higher percentages of sperm motility, stability of chromatin structure than glycerol only. In this study, we suggest that trehalose is effective in reducing freezing damage to miniature pig sperm and can reduce chromatin damage during cryopreservation.

• Fire Science and Engineering
• /
• v.26 no.1
• /
• pp.43-48
• /
• 2012

Recently, evacuation safety of building resident become the major concern, as the building has been higher and more complicated. Required evacuation time using stairway is longer in high-rise buildings, moreover it is impossible for the disabled to evacuate by using stairway. For this reason the study on the effectiveness of using elevator for evacuation is progressing. This study shows the flow coefficient of hoistway when elevator is moving. The results of this study can be used for the study of elevator piston effect as basic data. Experiments were performed in 5 different hoistways at 3-story and 2-story buildings. According to the result of flow coefficient experiments, average flow coefficient is 0.954. Considering the $4{\sigma}$ to guarantee 99.99 % reliance, it is 0.86. This result is 3.6 % bigger than 0.83 that Klote and Tamura suggested. It represents that the maximum critical pressure is decreased about 7 % on the same condition of elevator and elevator shaft. When the smoke control performance of high-rise building is evaluated, the result is significant economically by applying a more realistic and less value of elevator piston effect.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.1
• /
• pp.1-13
• /
• 2013

Salinity does not generally affect sound speed because it shows very small variations in the ocean. However, low salinity water appears in the Western Sea of Jeju Island every summer so that sound speed and sound propagation can change near sea surface. We calculated Sound Speed Profile (SSP) using vertical profiles of temperature and salinity, which were averaged over years of normal salinity and low salinity (<28 psu) from 30 years (1980~2009) at 3 sites of Korea Oceanographic Data Center (KODC). As a result, sound speed variation by low salinity alone was -5.36 m/s at sea surface and -1.35 m/s at 10m depth for low salinity environments. Gradient of SSP was positive down to 5 m depth due to decrease of sound speed near surface, leading formation of haline channel. Simulation of acoustic propagation using a ray model (Bellhop) confirmed the haline channel. Haline channel has formed 4 times while hydrostatic channel controlled by only pressure has formed 9 times for 30 years. The haline channel showed larger critical angles of rays than hydrostatic channel. Haline channel was also formed at some sites among 20 measurement sites in low salinity water mass which appeared on August $1^{st}$ 2010.