• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.511-517
• /
• 2001

We evaluated the electrical properties of 37 multifilamentary jointed tapes processed by superconducting joint. In the superconducting joining method, a lap-joint was used. Tapes were selectively etched, and exposed superconducting cores of the two tapes were brought into contact with each other and then only the joined region was uniaxially pressed in the range of 1,000 to 2,50 MPa. The critical current ratio(CCR) and n-value of the jointed tape were evaluated as a function of uniaxial pressure and number of step in the contacting region. It was observed that the CCR was dependent on the number of step, but almost independent of uniaxial pressure. The highest critical current ratio and n-value were obtained to be 58% and 26%, respectively, for the jointed tape to the tape itself.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.765-767
• /
• 1992

A superconducting multistranded cable is used to realize high current capacity for AC use. The critical current value of the cable to be less than the simple summation of individual critical current value of each strand. The causes for such a degradation of the critical current value have not been revealed. This paper investigates the current distribution in multistrands before and after their quenching by using 7-strand superconducting cable. The following experimental results are derived. (1)The quenching is initiated at one strand in the cable, (2)The current in the quenched strand is transferred into the other strands, (3) An avalanche of quenching is induced among the strands, (4)The central strand is quenched finally among the strands.

• Solar Energy
• /
• v.12 no.3
• /
• pp.126-136
• /
• 1992

In this paper an EGD generator of small capacity with the operating gases of $O_2,\;N_2$ and air is made and the electric characteristics in relation to energy conversion range length, corona current and gas pressure are investigated. The results are as follows: 1. There is a critical value in conversion range length for maximum open voltage and the critical value increases with fluid velocity. 2. The open voltage increases approximately linearly with corona current. 3. There is a critical value in the gas pressure for maximum open voltage and this pressure of gas decreases with fluid velocity in constant conversion range length.

• Journal of Power Electronics
• /
• v.12 no.5
• /
• pp.715-722
• /
• 2012

New discrete time domain models for the peak current controlled (PCC) power LED drivers in continuous conduction mode include for the first time the effects of the time delay in the pulse-width-modulator. Realistic amounts of time delay are found to have significant effects on the average output LED current and on the critical inductor value at the boundary between the two conduction modes. Especially, the time delay can provide an accurate LED current for the PCC buck converter with a wide input voltage. The models can also predict the critical inductor value at the mode boundary as functions of the input voltage and the time delay. The overshoot of the peak inductor current due to the time delay results in the increase of the average output current and the reduction of the critical inductor value at the mode boundary in all converters. Experimental results are presented for the PCC buck LED driver with constant-frequency controller.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1081-1083
• /
• 1993

A superconducting multistranded cable is used to realize high current capacity for AC use. The critical current value of the cable to be less than the simple summation of individual critical current value of each strand. The causes for such a degradation of the critical current value have not been revealed. This paper investigates the current distribution in multistrands before and after their quenching by using $7{\times}7$-strand superconducting cable.

• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.1-8
• /
• 1999

The magnetization and/or resistivity of high $T_c$ superconductors ($YBa_2Cu_3O_{7-\delta}$(YBCO) single crystal, $Bi_2Sr_2CaCu_2O_8$ (Bi-2212) single crystal, $Tl_2Ba_2CaCu_2O_8$ (Tl-2212) film, $HgBa_2Ca_2Cu_3O_8$ (Hg-1223) film) have been measured as a function of magnetic field H and temperature T. The extracted fluctuation part of the magnetization and conductivity exhibits a critical behavior consistent with the three-dimensional XY model. The dynamic critical exponent z does not sensitively vary with a type of the superconductors. The value of z ranges from 1.5 to $1.8{\pm}0.1$. However, the static critical exponent ${\nu}$ is the most largely increased in Tl-2212 that has a weaker interlayer coupling strength than YBCO; the value of ${\nu}$ is 0.669, 0.909, 1.19, and 1.338 for YBCO, Bi-2212, Hg-1223, and Tl-2212 respectively. The results indicate that the weak interlayer coupling along the c-axis of high $T_c$ superconductors near $T_c$ does not influence the dynamic critical exponent z (the same value of superfluid $^4He$), but significantly increases the static critical exponent ${\nu}$.

• Proceedings of the KSR Conference
• /
• 2001.05a
• /
• pp.437-442
• /
• 2001

In Korea, collapse of railway slopes is frequently occurred due to tycoon or heavy rainfall doling rainy season and has been made personal and social damage greatly. In order to evaluate the stability of railway slopes under rainfall, explanatory variables and subordinate variables were selected for multivariate analysis. The sites which failure had occurred due to rainfall were investigated and critical rainfall was defined by the case that had high value of correlation factor after multivariate analyses for 121 cases had been executed. The maximum hourly rainfall during 24 hours before failure caused the collapse of railway embankment and the 0.3 square value of maximum hourly rainfall during 24 hours before failure caused the collapse of railway cut-slope, From the application to collapse examples, it is judged that critical rainfall curve will be used to estimate the stability of slopes.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.59-60
• /
• 2014

To prevent the rusting of steel, a variety of finishing materials has been applied. When steel is exposed to an extreme chloride environment, however, the thermal performance and aging of the finishing materials cause the material to lose its rust protective performance. In this study, an accelerated corrosion test was performed on five different finishing materials for steel, to determine the critical values of corrosion. As the result, the critical value of corrosion was found with no coat between 0.58mg/d㎡ and 0.73mg/d㎡, with urethane coat between 7.89mg/d㎡~8.46mg/d㎡, with one-layered red lead coat between 57.95mg/d㎡ and 69.48mg/d㎡, and with staleness201 between 80.73mg/d㎡ and 89.35mg/d㎡.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.185-188
• /
• 1997

The influence of slow cooling and annealing time in $O_2$ during melting and growth step in MPMG process on J$_{c}$ was investigated. Through the measurement of J$_{c}$ SEM and XRD, it can be observed that the critical characteristics were related with the slow cooling time and annealing time in 02 for melting and growth step of MPMG process. The distribution of critical current density with slow cooling time was the porabolic form and the value of J. was the highest at the 40 hour slow cooling time. And also, the value of J$_{c}$, along the annealing time in $O_2$ in the case of the slow cooling time 40 hour was inclined to increase with annealing time. Consequently, it can be suggested that proper slow cooling titre and annealing time along slow cooling in MPMG process be important to improve the critical characteristics.stics.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.1
• /
• pp.49-55
• /
• 2012

Asynchronous counters, where the counter value is changed not by a synchronizing clock but by outer inputs, are used in various modern digital systems such as spaceborne electronics. In this paper, we propose a scheme of fault tolerance for asynchronous counters with critical races caused by total ionizing dose (TID) in space. As a typical design flaw of asynchronous digital circuits, critical races cause an asynchronous circuit to show non-deterministic behavior, i.e., the next stable state of a state transition is not a fixed value but may be any value of a state set. Using the corrective control scheme for asynchronous sequential machines, this paper provides an existence condition and design procedure for a state feedback controller that can invalidate the effect of critical races. We implement the proposed control system in VHDL code and conduct experiments to demonstrate that the proposed control system can overcome critical races.