• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.740-745
• /
• 1987

For the prediction of the crack growth initiation from a blunt notch or a precrack in a prestrained material under plane strain tension and small-scale yielding conditions, a microscopic fracture criterion is proposed in terms of the crack tip opening displacement(COD) needed for the attainment of fracture strain at a microstructural distance. Smooth blunting of a crack tip with an initial root radius is assumed, and strain distributions on the crack-line axis are calculated at each deformation stage until the distributions against an original distance normalized to the COD are insensitive to an initial root radius. This case of no initial-root-radius effect is taken as for a sharp crack tip, on which the criterion is applied to determine the characteristic length of material from a critical COD for a fatigue-precracked specimen. The predicted COD at the fracture initiation from a crack with an initial root radius or a prestraining shows reasonable agreement with experimental values.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1188-1195
• /
• 2007

The vertical forces in rail fasteners at areas of bridge transitions near the embankment and on the pier will occur due to different deformations of adjoining bridges caused by the trainloads, the settlement of supports, and the temperature gradients. The up-lifting forces is not large problem in the blast track because the elasticity of blast and rail pad buffs up-lifting effect. But, it is likely to be difficult to ensure the serviceability of the railway and the safety of the fastener in the end in that concrete slab track consist of rail, fastener, and track in a single body, delivering directly the up-lifting force to the fastener if the deck is bended because of various load cases, such as the end rotation of the overhang due to the vertical load, the bending of pier due to acceleration/braking force and temperature deviation, the settlement of embankment and pier, the temperature deviation of up-down deck and front-back pier, and the rail deformation due to wheel loads. The analysis of the rail fastener is made to verify the superposed tension forces in the rail fastener due to various load cases, temperature gradients and settlement of supports. The potential critical fasteners with the highest uplift forces are the fastener adjacent to the civil joint. The main influence factors are the geometry of the bridge such as, the beneath length of overhang, relative position of bridge bearing and fastener, deflection of bridge and the vertical spring stiffness of the fastener.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.14-17
• /
• 1999

The wrinkling behavior of a thin sheet with perfect geometry is a kind of compressive instability. The compressive instability is influenced by many factors such as stress state mechanical properties of the sheet material geometry of the body contact conditions and plastic anisotropy. The analysis of compressive instability in plastically deforming body is difficult considering all the factors because the effects of the factors are very complex and the instability behavior may show wide variation for small deviation of the factors. In this study the bifurcation theory is introduced for the finite element analysis of puckering initiation and growth of a thin sheet with perfect geometry. All the above mentioned analysis and the post-bifurcation behavior is analyzed by introducing the branching scheme proposed by Riks. The finite element formulation is based on the incremental deformation theory and elastic-plastic material modeling. in order to investigate the effect of plastic anisotropy on the compressive instability a square plate that is subjected to compression in one direction and tension in the other direction is analyzed by the above-mentionedfinite element analysis. The critical stress ratios above which the buckling does not take place are found for various plastic anisotropic modeling method and discussed. Finally the effect of plastic anisotropy on the puckering behavior in the spherical cup deep drawing process is investigated.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.84-89
• /
• 2004

There is a growing interest to replace the commercial steels with non-heat treated steels, which does not involve the spheroidization and quenching-tempering treatment. However, Non-heat treated steels should satisfy high strength and good formability without performing heat treatment. Therefore, it is important to investigate optimum materials showing a good combination of strength and formability after the drawing process. In this study, Dual-Phase Steels were studied as candidate materials for non-heat treated steels, which have different martensite morphologies and volume fractions obtained through heat-treatment of intercritical quenching (IcQ), intermediate quenching (ImQ) and step quenching (SQ). The mechanical properties of DP steels were measured by tension and compression tests. Also, the cold formability of three DP steels which have similar tensile strength value was investigated by estimating the deformation resistance and the forming limit. The deformation resistance which is important factor in determining die life was estimated by calculating the deformation energy. And the forming limit was estimated by measuring the critical strain revealing crack initiation at the notch tip of the specimens.

• International Journal of Advanced Culture Technology
• /
• v.6 no.3
• /
• pp.211-215
• /
• 2018

Ventilator-associated pneumonia (VAP) is a lung infection that develops in patients receiving mechanical ventilation. VAP contributes to about 50% of hospital-acquired pneumonia in ICU settings. One of the recommendation of the Institute of for Healthcare Improvement ventilator bundle is HOB elevation. HOB elevation affects shearing forces and makes higher risk for pressure injury development. Pressure injury (PI) is localized damage to the skin over a bony prominence. PI prevention guidelines recommend that HOB positioning should be lower to reduce risk for PI development which contradicts VAP prevention guidelines for the HOB between 30 and 45 degrees for ICU patients. This presents a care dilemma and tension. The purpose of this study was to perform a secondary data analysis using cumulative electronic health record data in order to determine the association of HOB elevation with VAP and PI in ICU patients. A secondary data analysis was conducted to determine whether HOB elevation is associated with VAP and PI. HOB elevation was not likely to be associated with VAP prevention whereas it was likely to be related to PI development. This is somewhat contrary to popular data and publications. Prospective cohort study is desired to inform us in an evidence-based fashion what actually is optimal HOB elevation for ventilated patients in ICU settings.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.1-6
• /
• 2000

FFP(Fitness For Purpose) type defect assessment methodologies based on ECA(Engineering Critical Analysis) have been established and are in use for the structural integrity evaluation of gas pipelines. ECA usually includes the fracture mechanics analysis, and it assumes that J-integral uniquely characterizes crack-tip stress-strain fields. However, it has been shown that it is not sufficient to characterize the crack-tip field under low levels of constraint with a single parameter. Since pipeline structures are made of ductile material, locally loaded in tension, cracks may experience low level of constraint, and therefore, J-dominance will be lost. For this reason, the level of constraint must be quantified to establish a precise assessment procedure for pipeline defects. The objective of this paper is to Investigate the fracture behavior of a crack in gas pipeline by quantifying the level of constraint. For this purpose, tensile tests and CTOD tests were performed at room temperature$(24^{\circ}C)$ and low temperature$(-40^{\circ}C)$ to obtain the material properties. J-Q analyses were performed for SENB and SENT specimens based on 2-D finite element analyses, in order to investigate the in-plane constraint effects on pipeline defects.

• Journal of the Korean Chemical Society
• /
• v.26 no.1
• /
• pp.49-57
• /
• 1982

Transesterification reactions were carried out with myo-inositol and five fatty acid methyl esters such as methyl laurate, methyl myristate, methyl palmitate, methyl stearate and methyl oleate in the dimethylsulfoxide solvent. Their products were separated by both thin layer chromatography and column chromatography, and myo-inositol monoesters were quantitatively separated by counter current distribution. We measured their surface tension, foaming power and emulsifying power, determined critical micelle concentrations by the color method, and evaluated their hydrophilic-lipophilic balance. The results show that myo-inositol monoesters exhibit surface activites.

• Journal of Korean Academy of Nursing
• /
• v.37 no.3
• /
• pp.353-364
• /
• 2007

Purpose: This study is aimed to analyze and clarify the ambiguous concept of insight. Method: This study used the process of Walker & Avant's concept analysis. Results: Insight can be defined in terms of its attributes as follows: Insight 1) comes as a release to the tension of inquiry, (2) is the outcome of the process to discover the overall structure of the problem situation and psychologically restructurize it, (3) comes suddenly and unexpectedly, (4) is to clearly perceive the solution of the abstract problem, and (5) promotes obtaining another new insight. The antecedents of insight include inquiry that can not be resolved easily and also a state where basic knowledge related to the inquiry can be utilized. The consequence of the insight is (1) a new judgement is made, (2) the problem is solved, (3) previous insight is retained and transferred, and it also facilitates the generation of fresh insight, and (4) it passes into the habitual texture of one's mind. Conclusion: Nurse educators need to facilitate nursing students and nurses to accumulate systematically, various information that can become the basis of insight and provide them with an opportunity to experience a variety of problems. In addition, it is important to provide questions to learners as an education strategy to allow them to gain insight into problem solving. From now on, insight needs to be studied in conjunction with critical thinking and questioning in order to enhance nurses' ability to resolve problems.

• Journal of the Korean Applied Science and Technology
• /
• v.3 no.1
• /
• pp.65-71
• /
• 1986

Four amphoteric surfactants, 1-(N-alkyl-N,N-dimethyl ammonio)-4-naphthalene sulfonates, were prepared by the alkylation of 1-(N,N-dimethylamino)-4,naphthalene sulfonic acid with chloroalkanes such as 1-decylchloride, 1-tetradecyl chloride and 1-hexadecyl chloride. These quaternary ammonium compounds such as 1-(N-decyl-N, N-dimethylammonio)-4-naphthalene sulfonate, 1-(N-dodecyl-N,N-dimethylammonio)-4-naphthalene sulfonate, 1-(N-tetradecyl-N,N-dimethylammonio)-4-naphthalene sulfonate and 1-(N-hexadecyl-N,N-dimethylammonio)-4-naphthalene sulfonate could be separated by means of thin layes chromatography and column chromatography. The surface chemical properties such as surface tension, foaming power, foam stability, wetting efficiency and solubilizing effect for these four compounds were measured. Also critical micelle concentration and hydrophilic-lipophilic balance(HLB) were evaluated. These compounds showed good surface as O/W type emulsifying agent and detergent.

• Journal of the Korean Applied Science and Technology
• /
• v.3 no.1
• /
• pp.57-64
• /
• 1986

1-(carboxyalkyl) trimethyl ammonium chlorides such as 1-(carboxyundecyl) trimethyl ammonium chloride and 1-(carboxytridecyl) trimethyiammonium chloride were synthesized by the reaction of ${\alpha}-bromoalkanoic$ acid with trimethyl amine hydrochloride. In other hand, (carboxymethyl) alkyl dimethyl ammonium chlorides such as (carboxymethyl) dodecyl dimethyl ammonium chloride and (carboxymethyl) tetradecyl dimethyl ammonium chloride were synthesized by the reaction of alkyl dimethylamine with sodium chloroacetate. The four kinds of alky carboxy betaine such as 2-(trimethylammonio) dodecanoate, 2-(trimethyl ammonio) tetradecanoate, (dodecyl dimethylammonio) ethanoate and (tetradecyl dimethyl ammonio) ethanoate were prepared from 1-(carboxyalkyl) trimethyl ammonium chlorides or (carboxymethy1) alkyl dimethyl ammonium chlorides. The surface activities including surface tension, emulsifying power, foaming power, foam stability, deflocculating effect, effectiveness of wettability and solubilizing effect were measured and also critical micelle concentration and hydrophilic-lipophilic. balance(HLB) were evaluated. These carboxy betaines show good surface activities as O/W type emulsifing agent and detergent.