• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.377-380
• /
• 1999

This paper dscribes an experimental investigation into the cause of flexural-shear failure in RC beams. The experimental variables are bottom flange width and tension bar location. Then these test results were compared and analyzed to deduce the major cause of critical-shear cracking. As a result, it was found that the propagation of the critical shear crack depended exclusively on the intensity of horizontal cracking.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.45-51
• /
• 2013

Short beam tests of GFRP and CFRP specimens exposed to high temperature were conducted to measure the inter-laminar shear strength. For the phase I test, the exposure time and temperature were varied to measure reduction in the strength due to the applied conditions. As a results, the critical temperature was found to $270^{\circ}C$ for the both FRP reinforcements. The high temperature, which causes 50% loss of inter-laminar shear strength, is defined as the critical temperature in this study. It should be noted that the critical temperature for the inter-laminar shear strength is mainly dependent on resin properties not on fiber type. In the phase II test, the effect of exposure time was investigated at intervals of 0.25hour for the critical temperature. All test results demonstrate that the exposure time effect is not significant compared to the maximum exposure temperature, but it is not negligible and, moreover, is significant at the critical temperature.

• Computers and Concrete
• /
• v.3 no.1
• /
• pp.65-77
• /
• 2006

This study reports the details of the finite element analysis of eleven shear critical partially prestressed concrete T-beams having steel fibers over partial or full depth. Prestressed concrete T-beams having a shear span to depth ratio of 2.65 and 1.59 and failing in the shear have been analyzed using 'ANSYS'. The 'ANSYS' model accounts for the nonlinear phenomenon, such as, bond-slip of longitudinal reinforcements, post-cracking tensile stiffness of the concrete, stress transfer across the cracked blocks of the concrete and load sustenance through the bridging of steel fibers at crack interface. The concrete is modeled using 'SOLID65'-eight-node brick element, which is capable of simulating the cracking and crushing behavior of brittle materials. The reinforcements such as deformed bars, prestressing wires and steel fibers have been modeled discretely using 'LINK8' - 3D spar element. The slip between the reinforcement (rebar, fibers) and the concrete has been modeled using a 'COMBIN39'-non-linear spring element connecting the nodes of the 'LINK8' element representing the reinforcement and nodes of the 'SOLID65' elements representing the concrete. The 'ANSYS' model correctly predicted the diagonal tension failure and shear compression failure of prestressed concrete beams observed in the experiment. The capability of the model to capture the critical crack regions, loads and deflections for various types of shear failures in prestressed concrete beam has been illustrated.

• Korea-Australia Rheology Journal
• /
• v.15 no.2
• /
• pp.63-73
• /
• 2003

An experimental technique was developed to determine the strain-rate in a tensile specimen. Then one can calculate the transient isothermal elongational viscosity. Both shear and elongational viscosities were measured to study the effect of shear and elongational fields on the flow properties. The comparison between these viscosities shows that the onset of rapid viscosity growth as crystallization solidification proceeds occurs at about the same value of time at very small deformation rates (0.0028 and 0.0047 $s^{-1}$). The comparison of these measured viscosities as functions of shear and elongational Hencky strains also reveals that the onset of rapid viscosity growths starts at critical Hencky strain values. The behaviour of steady shear viscosity as function of temperature sweep was also explored at three different low shear rates. Finally, the influence of changing oscillatory frequencies and strain rates was also investigated.

• Architectural research
• /
• v.18 no.3
• /
• pp.113-120
• /
• 2016

The stability and resistance of the plates under in-plane loading is crucial in the design of structures. For the assessment of structural stability, it is necessarily required to have accurate finite element technologies. Therefore, the enhanced 9-node plate (Q9-ANS) element is introduced for the linear buckling analysis of plate where the critical buckling load has to be determined. The Q9-ANS is developed with the Reissner-Mindlin (RM) assumptions which consider transverse shear deformation of the plate. Assumed shear strain is used to alleviate the shear locking phenomenon. Numerical examples are carried out to verify the performance of the Q9-ANS element in calculation of critical buckling load of the plates.

• Steel and Composite Structures
• /
• v.48 no.2
• /
• pp.145-161
• /
• 2023

This study investigates the influences of porosity on the stability of the orthotropic laminated plates under uniaxial and biaxial loadings based on the hyperbolic shear deformation theory. Three different porosity distribution are considered with three specific functions through the plate thickness. The stability equations of porous orthotropic laminated plates are derived by the virtual work principle. Applying the Galerkin method to partial differential equations, the critical buckling load relation of porous orthotropic laminated plates is obtained. After validating the accuracy of the proposed formulation in accordance with the available literature, a parametric analysis is performed to observe the sensitivity of the critical buckling load to shear deformation, porosity, orthotropy, loading factor, and different geometric properties.

• Applied Chemistry for Engineering
• /
• v.22 no.4
• /
• pp.384-389
• /
• 2011

We made suspension of fumed silica in polyethylene glycol (PEG), studied rheological behavior as functions of contents of silica, dispersion condition, PEG molecular weight, temperature and contents of humidity. Rheological behavior of suspension was determined critical shear rate and rise of viscosity using rheometer AR2000. Suspension were PEGs of molecular weight 200, 400, and 600. Fumed silica suspensions of which silica contents are 5, 7, 9, 13, and 18% were prepared by normal mixing, homogenization and bead milling process. We observed their rheological behaviors at 10, 20, 30, and $40^{\circ}C$. As the PEG molecular weight and contents of silica increase, the critical shear rate was lowered. As the temperature increased, the critical shear rate was increased. Humidity contents of dispersion don't influence on the critical shear rate, but dispersion processes greatly affect the critical shear rate. The critical shear rate of suspensions prepared by the mixing process was the lowest, and that of suspensions prepared by the bead milling process was the highest. The rise in the shear viscosity of suspensions prepared by the mixing process is higher than that of suspensions prepared by the bead milling process. This was dependent on the dispersion condition of silica particle by dispersion process.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.370-373
• /
• 2006

According to current design provisions for shear strength of reinforced concrete slabs, critical slab sections around columns should be modified in the presence of openings in slabs to consider the effect of openings on the shear strength of slabs. Although the method of estimating the ineffective part of critical section due to openings are explained in codes, the real math for calculating it is somewhat complex and cumbersome. This paper classifies different cases of the location and geometry of columns and openings, respectively, and derives corresponding equations for estimating ineffective part of critical section for each case.

• Structural Engineering and Mechanics
• /
• v.24 no.2
• /
• pp.247-268
• /
• 2006

The parts of pile, above the soil and embedded in the soil are called the first region and second region, respectively. The forth order differential equations of both region for critical buckling load of partially embedded pile with shear deformation are obtained using the small-displacement theory and Winkler hypothesis. It is assumed that the behavior of material of the pile is linear-elastic and that axial force along the pile length and modulus of subgrade reaction for the second region to be constant. Shear effect is included in the differential equations by considering shear deformation in the second derivative of the elastic curve function. Critical buckling loads of the pile are calculated for by differential transform method (DTM) and analytical method, results are given in tables and variation of critical buckling loads corresponding to relative stiffness of the pile are presented in graphs.

• Steel and Composite Structures
• /
• v.32 no.4
• /
• pp.443-454
• /
• 2019

With the aim to put forward the analytical model for calculating the shear capacity of precast steel reinforced concrete (PSRC) beams, a static test on two full-scale PSRC specimens was conducted under four-point loading, and the failure modes and strain developments of the specimens were critically investigated. Based on the test results, a modified truss-arch model was proposed to analyze the shear mechanisms of PSRC and cast-in-place SRC beams. In the proposed model, the overall shear capacity of PSRC and cast-in-place SRC beams can be obtained by combining the shear capacity of encased steel shape with web concrete determined by modified Nakamura and Narita model and the shear capacity of reinforced concrete part determined by compatible truss-arch model which can consider both the contributions of concrete and stirrups to shear capacity in the truss action as well as the contribution of arch action through compatibility of deformation. Finally, the proposed model is compared with other models from JGJ 138 and AISC 360 using the available SRC beam test data consisting of 75 shear-critical PSRC and SRC beams. The results indicate that the proposed model can improve the accuracy of shear capacity predictions for shear-critical PSRC and cast-in-place SRC beams, and relatively conservative results can be obtained by the models from JGJ 138 and AISC 360.