• 한국항공우주학회지
• /
• 제30권8호
• /
• pp.103-111
• /
• 2002

열하중과 원심력을 고려한 발전용 터빈 블레이드의 정상 상태 크리프 해석을 수행하였다. 3차원 터빈 블레이드 유한 요소 모델에 대하여 크리프 변형률과 응력을 계산하고 수치적 방법에 의해 크리프 수명을 예측하였다. 약 200시간 정도의 크리프 해석 결과 GTD111 터빈 블레이드는 아직 파손 응력에 도달하지 않았으며, 크리프 응력은 시간이 경과함에 따라 점차 이완되고 있다. 터빈 블레이드의 최대 크리프 변형률은 익형의 압력면 끝단에서 발생하며 수치적 방법에 의해 약 50,000 시간 이후에 파손 변형률에 도달할 것이다. 따라서 현재 터빈의 기동 중 블레이드는 크리프에 의한 손상을 입지 않는다.

• Geomechanics and Engineering
• /
• 제35권1호
• /
• pp.55-65
• /
• 2023

Soft clay is widely spread in nature and encountered in geotechnical engineering applications. The creep property of soft clay greatly affects the long-term performance of its upper structures. Therefore, it is vital to establish a reasonable and practical creep constitutive model. In the study, two updated hyperbolic equations based on the volumetric creep and deviatoric creep are respectively proposed. Subsequently, three creep constitutive models based on different creep behavior, i.e., V-model (use volumetric creep equation), D-model (use deviatoric creep equation) and VD-model (use both volumetric and deviatoric creep equations) are developed and compared. From the aspect of prediction accuracy, both V-model and D-model show good agreements with experimental results, while the predictions of the VD-model are smaller than the experimental results. In terms of the parametric sensitivity, D-model and VD-model are lower sensitive to parameter M (the slope of the critical state line) than V-model. Therefore, the D-model which is developed by incorporating the updated deviatoric creep equation is suggested in engineering applications.

• Steel and Composite Structures
• /
• 제19권1호
• /
• pp.111-129
• /
• 2015

This paper first presents an experimental study of twelve specimens for their creep performance, including nine concrete-filled steel tubular (CFST) columns and three plain concrete columns, subjected to three levels of sustained axial loads for 1710 days. Then, the creep strain curves are predicted from the existing creep models including the ACI 209 model, the MC 78 model, and the MC 90 model, and further a fitted creep model is obtained by experimental data. Finally, the creep effects of a CFST arch bridge are analyzed to compare the accuracy of the existing creep models. The experimental results show that the creep strains in CFST specimens are far less than in the plain concrete specimens and still increase after two years. The ACI 209 model outperforms the MC 78 model and the MC 90 model when predicting the creep behavior of the CFST specimens. Analysis results indicate that the creep effects in the CFST arch bridge are significant. The deflections and stresses calculated by the ACI 209 model are the closest to the fitted model in the three existing models, demonstrating that the ACI 209 model can be used for creep analysis of CFST arch bridges and can meet the engineering accuracy requirement when lack of experimental data.

• 한국세라믹학회지
• /
• 제30권4호
• /
• pp.251-258
• /
• 1993

A constitutive model is proposed to analyze creep densification and grain growth of ceramic powder compacts. The creep strain rates for powder compacts are obtained from constitutive equations proposed by Rahaman et al. and Helle et al. The grain-growth rate is obtained by assuming time, grain size, and strain rate as its internal state variables. the proposed constitutive model is compared with experimental data for alumina compacts obtained by Venkatachari and Raj for sinter forging and by Son et al. for hot pressing.

• 콘크리트학회논문집
• /
• 제13권3호
• /
• pp.268-276
• /
• 2001

본 논문은 고온에서의 콘크리트 재료모델을 연구하였다. 콘크리트 응력-변형률 곡선은 온도가 증가함에 따라 그 형태가 변한다. 온도에 따른 콘크리트 재료거동의 변화를 나타내기 위하여 변형된 Saenz 제안식을 이용하여 응력-변형률 관계를 표시하였다. 고온에서의 급격한 변형률의 증가현상을 설명하기 위하여, 콘크리트의 변형률 성분을 순수 열팽창 변형률, 열적크리프 변형률, 과도 변형률 및 역학적 변형률로 구분하여 나타내었다. 열적크리프 변형률은 Baily-Norton의 장기크리프 곡선 식을 수정.제안하여 1축 실험 결과를 온도, 시간 및 응력의 함수로 표현하였고, 또한 유효응력 및 유효변형률 개념을 도입하여 다차원에서도 적용할 수 있는 모델을 제시하였다. 과도 변형률을 제안하여 다공탄성 거동을 가정한 콘크리트 내에 포함된 공극 및 수분의 작용을 역학적 거동의 영향을 분석하고자 하였다. 마지막으로, 본 논문에서 제시한 고온에서의 콘크리트 재료모델을 이용한 해석결과를 실제 화재실험자료와 비교하였다.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.91-97
• /
• 1998

The analysis model is the infinite body consisted of power law creep material containing a rigid inclusion with line crack shape subjected to the arbitrarily directional stress on an infinite boundary. The crack analysis is performed using the complex pseudo-stress function. The strain rate intensity factor is determined in the closed form as new fracture mechanics parmeter which represents the magnitudes of stress and strain rate near the tip in power law creep material.

• Journal of Biosystems Engineering
• /
• 제14권3호
• /
• pp.181-187
• /
• 1989

The mechanical and rheological properties of agricultural materials which influence the machine design or handling are not completely understood. Agricultural materials do not react in a purely elastic manner, and their responses when subjected to stress and strain appear a combination of elastic and viscous behavior. Many researchers have studied the mechanical and rheological properties of the various agricultural materials, but those properties are available mostly for foreign varieties of agricultural products. Rheological properties of rice seedlings become important to formulate the principles governing their mechanical behavior. The objectives of this study were to experimentally determine the creep and recovery behavior of rice seedlings of one japonica-type and one Indica x japonica hybrid in the transplanting age. The results of this study are summarized as follows; 1. The compression creep and recovery behavior of mat-type seedlings could be described by 4-element Burger's model. 2. The steady-state creep appeared at the stress larger than 0.8 MPa and the logarithmic creep appeared at the stress smaller than 0.8 MPa. 3. In the compression creep test of the rice seedlings, the instantaneous elastic modulus of Burger's model showed the range from 20 to 40 MPa. The higher value of absolute viscosity for the rice seedling explained that the rice seedlings were viscoelastic materials. 4. In the recovery test of the rice seedlings, there was a tendency that the higher permanent strain of all samples was observed under the smaller stress being appeared, and the larger permanent strain in Dongjin was observed than in Samkang.

• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2901-2909
• /
• 2020

Thermal creep is a key property of zircaloy cladding. CZ developed by CGN is a new zircaloy used as PWR fuel cladding. This research is devoted to investigating the thermal creep behavior of CZ and build the thermal creep model of CZ. Twenty internal pressure creep tests were conducted, and the ranges of temperature and Tresca stress were 320-430 ℃ and 70-300 MPa, respectively. Real-time creep data were analyzed by separating primary creep and steady-state creep. Based on Soderberg model and creep test data, CZ thermal creep model is derived. As a whole, the mean value and the standard deviation of P/M of CZ saturated primary creep strain are very close to these from steady-state creep rate, however, the predictive effect of primary creep is less satisfactory. Four conditions, where there exists large deviation between predicted values and test data, are 320 ℃ and 300 MPa, 350 ℃ and 190 MPa, 380 ℃ and 160 MPa, 380 ℃ and 190 MPa, respectively. As primary creep was much smaller than steady-state creep in long-time operation, the thermal creep model built can be applied to predict the thermal creep behavior of CZ cladding.

• 한국농공학회지
• /
• 제30권4호
• /
• pp.134-153
• /
• 1988

This paper was carried out to investigate the existence of a unique stress- strain behavior by obtaining some factors influencing the time dependent stress- strain behavior of clay. The results obtained from this study were summarized as follows ; 1. The relationship between stress ratro and strain in normally consolidated clay was in- dependent on pre-shear consolidation pressure. Therefore, shear strain could be expressed as a function with stress ratio. 2. The constitutive equation of shear strain on Modified Carn Clay Model coincided better with the observed value than Cam Clay Model. 3. The relationships between deviator stress and shear strain, between pore water pressure and shear strain were unified by the mean equivalent pressure. 4. The shear strain contour in norrnally consolidated clay was increased linearly through origin, but that in overconsolidated clay was not in accordance with the result of the former. 5. Because the effective stress path of normally consolidated clay was unified by the mean equivalent pressure, state boundary surface in (e,p,q) space was transformed into two dimensional surface. But it was considered to be suitable that the unified stress- strain in overconsolidated clay be expressed by a function with overconsolidation ratio. 6. The deviator for constant strain was increased linearly with increment of strain rate ($\varepsilon$) on semi-log scale, but pore water pressure was decreased. 7. The behavior of stress relaxation was transformed from linear to curvilinear with inc - rement of strain rate before stress relaxation test, and pore water pressure was increased in total range. 8. The strain of creep was increased linearly with increment of time on semi-log scale. The greater the strain rate before creep test became, the greater the increment of strain of creep became. And the pore water pressure during creep test was increased generally with increment of time on semi-log scale.

• Geomechanics and Engineering
• /
• 제23권6호
• /
• pp.535-546
• /
• 2020

The stress environment of deep rock masses is complex. Under the action of earthquakes or blasting, the strength and stability of anchored rock masses in fracture zones or faults are affected. To explore the variation in anchored rock masses under creep-fatigue loading, shear creep comparative testing of anchored marble specimens with or without fatigue loading is performed. Considering the damage variable of rock under fatigue loading, a rheological model is established to characterize the whole shear creep process of anchored rock masses under creep-fatigue loading. The results show that (1) the overall deformation of marble under creep-fatigue loading is larger than that under only shear creep loading, and the average deformation is increased by 18.3%. (2) By comparing the creep curves with and without fatigue loading, the two curves basically coincide when the first level stress is applied, and the two curves are stable with the increase in stress level. The results show that the strain difference among the specimens increases gradually in the steady-state stage and reaches the maximum at the fourth level. (3) The shear creep is described by considering the creep mechanical properties of anchored rock masses under fatigue loading. The accuracy of this creep-fatigue model is verified by laboratory tests, and the applicability of the model is illustrated by the fitting parameter R2. The proposed model provides a theoretical basis for the study of anchored rock masses under low-frequency earthquakes or blasting and new methods for the stability and reinforcement of rock masses.