• Journal of Welding and Joining
• /
• 제20권6호
• /
• pp.30-30
• /
• 2002

It has been reported that the creep characteristics on weldment which is composed of weld metal(W.M), fusion line(F.L), heat-affected zone(HAZ), and base meta(B.M) could be unpredictably changed in severe service conditions such as high temperature and high pressure. However, the studies done on creep damage in power plant components have been mostly conducted on B.M and not the creep properties of the localized microstructures in weldment have been thoroughly investigated yet. In this paper, it is investigated the creep characteristics for three microstructures like coarse-grain HAZ(CGHAZ), W.M, and B.M in X20CrMoV121 steel weldment by the small punch-creep-(SP-Creep) test using miniaturized specimen(l0×10×0.5mm). The W.M microstructure possesses the higher creep resistance and shows lower creep strain rate than the B.M and CGHAZ. In the lower creep load the highest creep strain rate is exhibited in CGHAZ, whereas in the higher creep load the B.M represents the high creep strain rate. The power law correlation for all microstructures exists between creep rate and creep load at 600℃. The values of creep load index (n) based on creep strain rate for B.M, CGHAZ, and W.M are 7.54, 4.23, and 5.06, respectively and CGHAZ which shows coarse grains owing to high welding heat has the lowest creep loade index. In all creep loads, the creep life for W.M shows the highest value.

• Journal of Welding and Joining
• /
• 제20권6호
• /
• pp.754-761
• /
• 2002

It has been reported that the creep characteristics on weldment which is composed of weld metal(W.M), fusion line(F.L), heat-affected zone(HAZ), and base meta(B.M) could be unpredictably changed in severe service conditions such as high temperature and high pressure. However, the studies done on creep damage in power plant components have been mostly conducted on B.M and not the creep properties of the localized microstructures in weldment have been thoroughly investigated yet. In this paper, it is investigated the creep characteristics for three microstructures like coarse-grain HAZ(CGHAZ), W.M, and B.M in X20CrMoV121 steel weldment by the small punch-creep-(SP-Creep) test using miniaturized specimen($10{\times}10{\times}0.5mm$). The W.M microstructure possesses the higher creep resistance and shows lower creep strain rate than the B.M and CGHAZ. In the lower creep load the highest creep strain rate is exhibited in CGHAZ, whereas in the higher creep load the B.M represents the high creep strain rate. The power law correlation for all microstructures exists between creep rate and creep load at $600^{\circ}C$. The values of creep load index (n) based on creep strain rate for B.M, CGHAZ, and W.M are 7.54, 4.23, and 5.06, respectively and CGHAZ which shows coarse grains owing to high welding heat has the lowest creep loade index. In all creep loads, the creep life for W.M shows the highest value.

• Geomechanics and Engineering
• /
• 제24권1호
• /
• pp.43-55
• /
• 2021

Peatland is distributed in China widely, and organic matters in soil frequently induce problems in the construction and maintenance of highway engineering due to the high permeability and compressibility. In this paper, a selected site of Dali-Lijiang expressway was surveyed in China. A numerical model was built to predict the settlement of the foundation of the selected section employing the soft soil creep (SSC) model in PLAXIS 8.2. The model was subsequently verified by the result of field observance. Consequently, the parameters of 17 types of soils from different regions in China with organic contents varying from 1.1-74.9% were assigned to the numerical model to study the settlement characteristics. The calculated results showed that the duration of primary consolidation and proportion of primary settlement in the total settlement decreased with increasing organic content. Two empirical equations, for total consolidation settlement and secondary settlement, were proposed using multiple linear regression based on the calculated results from the numerical models. The analysis results of the significances of certain soil parameters demonstrated that the natural compression index, secondary compression index, cohesion and friction angle have significant linear relevance with both the total settlement and secondary settlement, while the initial coefficient of permeability exerts significant influence on the secondary settlement only.

• 한국도로학회논문집
• /
• 제11권2호
• /
• pp.167-174
• /
• 2009

본 논문에서는 아스팔트 콘크리트 포장의 표층 프로파일과 차량특성인 차량속도와 현가장치를 다르게 하여 트럭 시뮬레이션 프로그램을 통한 동적하중을 분석하였다. 다양한 포장 상태의 프로파일을 입력하여 동적하중을 분석하였으며 프로파일, 차량의 현가장치, 차량속도에 따른 동적하중 변화를 분석하였다. 포장 거칠기가 증가할수록 동적하중이 증가하였으며, 속도가 증가할 수 록 동일한 포장 거칠기 하에서 동적하중이 증가하였다. Walking beam 현가장치가 Air spring 현가장치에 비해 더 큰 동적하중을 보였다. 동적하중 공분산을 이용하여 포장파손 지수를 결정하였으며, 동적하중 공분산과 신뢰도, 아스팔트 혼합물의 파괴매개변수가 증가할 수록 포장파손지수도 증가하였다. 본 연구의 결과를 이용하여 차량속도와 표층 아스팔트 혼합물 파괴특성에 근거한 포장 평탄성 규정에 이용할 수 있으며, 아스팔트 콘크리트 포장 시공 후 포장 평탄성에 근거한 지불규정에 효과적으로 사용할 수 있다고 판단된다.

• 한국해양공학회지
• /
• 제25권6호
• /
• pp.110-115
• /
• 2011

Numerouslong-term consolidation and secondary compression settlements may occur in Busan clay, which is astructured soft clay and consists of a thick clay deposit. As a surcharge load is applied to soils, soils experience different stress paths with depth. Therefore, it is necessary to study the long-term consolidation behavior of Busan clay considering stress conditions such as OC or NC states. In this study, a series of long-term consolidation tests were performed to investigate the consolidation characteristics of Busan clay for 20 days. The undisturbed clay samples were taken from 3 sites located in the Nakdong River estuary. The results showed that the creep rate of the Busan clay gradually decreased with time, which indicated that the secondary compression settlement decreased with time. In addition, the experimental results for 3 samples showed that the ratios were about 0.0363 and 0.051, respectively.

• 농업과학연구
• /
• 제10권1호
• /
• pp.110-117
• /
• 1983

본(本) 연구(硏究)는 쌍곡선법(雙曲線法)을 이용(利用)해서 하중(荷重) 증가율(增加率)이 이차압밀(二次壓密)에 마치는 영향(影響)을 구명(究明)하기 위하여, 아산만(牙山灣)의 해성점토(海成粘土)에 대(對)하여 시험(試驗)한 것으로 그의 결과(結果)를 요약(要略)하면 다음과 같다. 1. 쌍곡선법(雙曲線法)에 의(依)한 이차압밀량산정(二次壓密量算定) 값은 Casagrande의 log t 법(法)에 의(依)한 값보다 약간 작았으나, 그 차이(差異)는 미소(微小)하였고 쌍곡선법(雙曲線法)으로는 하중(荷重) 증가율(增加率)이 작을 때에도 쉽게 이차압밀량(二次壓密量)을 산정(算定)할 수 있었다. 2. 하중증가율(荷重增加率)이 작을수록 이차압밀비(二次壓密比)는 크게 나타났으며 하중증가율(荷重增加率)이 작을때 일어나는 심하곡선(沈下曲線)의 creep 현상(現象)은 이차압밀(二次壓密)에 기인(起因)한 것이라 생각된다. 3. 일차압밀중(一次壓密中)에 생기는 이차압밀(二次壓密)는 과압밀영역(過壓密領域)에서는 불규칙(不規則)했으나, 과압밀영역(過壓密領域)에서는 하중증가율(荷重增加率)이 작을수록 증가현상(增加現象)을 보였다. 4. 이차압밀계수(二次壓密係數)는 하중(荷重)의 증가(增加)에 따라 점차 증가(增加)하여 선행하중근처(先行荷重近處)에서 변곡점(變曲点)을 이루었고 하중(荷重)이 $2kg/cm^2$부터는 감소현상(減少現象)을 나타냈으며 이차압밀계수(二次壓密係數)는 하중증가율(荷重增加率)과 무관(無關)함을 보였다. 5. 이차압밀계수(二次壓密係數)와 압축지수(壓縮指數)는 비례관계(比例關係)를 나타냈다.

• 한국지반공학회논문집
• /
• 제30권2호
• /
• pp.53-64
• /
• 2014

이 연구에서는, 균질한 재성형 점토를 이용한 실내시험을 통해 정규압밀 영역에서의 하중재하기간이 점성토의 압축 및 장기압밀 특성에 미치는 영향을 명확히 하고자 하였다. 또한 각 하중재하기간에 따른 현장에서의 유효상재하중에 해당하는 초기압밀하중을 변화시킨 장기압밀 시험을 수행하여 표준압밀시험시의 하중단계별 재하방법과 하중재하기간의 증가에 따른 압축곡선의 특성을 비교/분석하여 하중재하기간에 따라 최종침하량을 예측하는 방법을 제안하고자 하였다. 연구 결과 하중재하기간에 따른 점성토의 압축특성은 초기압밀하중을 가한 후 하중재하기간이 증가할수록 주어진 단계에서의 압밀후반부의 2차압밀의 증가로 선행압밀하중이 약간씩 감소하는 경향을 나타내었다. 그와 동시에 2차압밀이 유사과압밀 현상 및 점토골격의 안정화를 유발하여 정규압밀영역에서의 압축지수에 미치는 영향은 미미했으며 과압밀영역에서는 유사과압밀 현상으로 재압축지수의 증가를 유발하는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1115-1123
• /
• 2008

When constructing projects such as road embankments, bridge approaches, dikes or buildings on soft, compressible soils, significant settlements may occur due to the consolidation of these soils under the superimposed loads. The compressibility of the soil skeleton of a soft clay is influenced by such factors as structure and fabric, stress path, temperature and loading rate. Although it is possible to determine appropriate relations and the corresponding material parameters in the laboratory, it is well known that sample disturbance due to stress release, temperature change and moisture content change can have a profound effect on the compressibility of a clay. The early research of Tezaghi and Casagrande has had a lasting influence on our interpretation of consolidation data. The 24 hour, incremental load, oedometer test has become, more or less, the standard procedure for determining the one-dimensional, stress-strain behavior of clays. An important notion relates to the interpretation of the data is the ore-consolidation pressure ${\sigma}_p$, which is located approximately at the break in the slope on the curve. From a practical point of view, this pressure is usually viewed as corresponding to the maximum past effective stress supported by the soil. Researchers have shown, however, that the value of ${\sigma}_p$ depends on the test procedure. furthermore, owing to sampling disturbance, the results of the laboratory consolidation test must be corrected to better capture the in-situ compressibility characteristics. The corrections apply, strictly speaking, to soils where the relation between strain and effective stress is time independent. An important assumption in Terzaghi's one-dimensional theory of consolidation is that the soil skeleton behaves elastically. On the other hand, Buisman recognized that creep deformations in settlement analysis can be important. this has led to extensions to Terzaghi's theory by various investigators, including the applicant and coworkers. The main object of this study is to suggestion the modified compression index value to predict settlements by back calculating the $C_c$ from different numerical models, which are giving best prediction settlements for multi layers including very thick soft clay.