• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.417-420
• /
• 2004

The Prestressed concrete girder bridges(PSC girder bridges), consisting of prestressed concrete girders and cast-in-place deck slabs, are sensitive to creep and shrinkage of concrete. Shrinkage and creep produce additional internal forces md deformations in PSC girder bridges. The long-term behavior of the PSC girder bridges depends on time-dependent properties of materials, amount of prestressing, methods and sequences of construction and age at loading. The purpose of this study is to predict the long-term behavior of PSC girder bridge. For this purpose, Computer program for Time-dependent analysis of PSC girder bridge has been developed. thereafter, Time-dependent analysis using developed computer program was carried out about 3-span continuous PSC girder bridges. Various construction timing sequences were used for parametric study.

• Korean Journal of Metals and Materials
• /
• v.48 no.11
• /
• pp.965-973
• /
• 2010

The small punch creep (SPC) test has recently received much attention as a new alternative to the conventional uniaxial creep test because it needs only a miniature-sized specimen directly detached from an operating system or component without any serious sampling damages. However, it is difficult to obtain the equivalent uniaxial creep data directly from the SPC data. As a specimen is deformed by a punch in the SPC test, the test result is sensitive to the friction between them. Finite element analyses with various friction coefficients was performed and showed a tendency of increased SPC life with an increased friction coefficient. The necking position predicted by the SPC simulation with a proper friction coefficient showed good agreement with that observed from the real SPC test. Finally, a noble method to convert the SPC load and displacement rate into the equivalent uniaxial creep stress and strain rate, respectively, was established in this study.

• Korean Journal of Metals and Materials
• /
• v.49 no.9
• /
• pp.686-691
• /
• 2011

To develop creep resistant die-cast Mg alloys, various alloying elements, including Ca, Ce, and Sr, were added to a Mg-Al alloy. The AXE710 alloy was produced on a 320 ton high-pressure die casting machine. The microstructure and creep properties of the alloy were examined. The creep behavior was investigated at $150^{\circ}C$ for stresses ranging from 50 to 100 MPa. The stress exponent was derived from the relationship between normalized secondary creep rates and compensated effective stresses. It was found to be 4.9, indicating that the dislocation climb is a dominant creep mechanism.

• Proceedings of the Korean Reliability Society Conference
• /
• 2005.06a
• /
• pp.69-73
• /
• 2005

The failure of geogrids used for soil reinforcement application can be defined as an excessive creep strain which causes the collapse of slopes and embankments. Accordingly, the lifetime is evaluated as a time to reach the excessive creep strain using two accelerated creep testing methods, time-temperature superposition(TTS) and stepped isothermal methods(SIM). TTS is a well-accepted acceleration method to evaluate creep behavior of polymeric materials, while SIM was developed in the last ten years mainly to shorten testing time and minimize the uncertainty associated with inherent variability of multi-specimen tests. The SIM test is usually performed using single rib of geogrids for temperature steps of $14^{\circ}C$ and a dwell time of 10,000 seconds. However, for multi-ribs of geogrids, the applicability of the SIM has not been well established. In this study, the creep behaviors are evaluated using multi-ribs of polyester geogrids using SIM and TTS creep procedures and the newly designed test equipment. Then the lifetime of geogrids are predicted by analyzing the failure times to reach the excessive creep strains through reliability analysis.

• Korean Journal of Agricultural Science
• /
• v.22 no.1
• /
• pp.1-10
• /
• 1995

All agricultural crops and products should be cultured, harvested, handled and processed by the proper mechanical methods in the mechanized farming systems. Agricultural crops might be injured or deformed through various working stages due to static or dynamic forces of machines. Mechanical forces had to be applied with proper degrees to the agricultural crops in incoincidence with properties of crops without any damage of crops so as to increase the work efficiency qualitatively. Knowledges of mechanical properties of agricultural materials are essential to prevent of agricultural crops in relation with mechanical farming system. This study was carried out to examine and analyze the creep behavior of the rice stalk on growing and harvesting periods by mechanical model with computer measurement system in radial directional compressive force and bending force. The creep behavior of the rice stalk could be predicted precisely and its results approached closely to the measured values. The creep behaviors were increased greatly with increase of compressive force, namely, the steady state creep behavior occurred at the force less then 25N and the logarithmic creep behavior at the force bigger than 30N. The instantaneous elastic modulus $E_o$ and the retardation time ${\tau}_K$ were increased together with increase of applied forces, meanwhile the retarded elastic modulus $E_r$ and viscosity ${\eta}_v$ were decreased with increase of applied forces in mechanical model being expected the creep behavior in relation with the level of applied forces, which was well explained that the rice stalk might be visvo-elastic material. In the creep test along the stalk portion with compressive force and bending force, the intermediate portion showed greatest values and also the lower portion showed the least values, which implied that the intermediate portions of rice stalk were very weak. The steady state creep behavior occured at the intermediate portion and the upper portion in the rice stalk at the compressive force larger than 25.0N, which showed the possibility of injury due to external forces.

• 대한공업교육학회지
• /
• v.35 no.2
• /
• pp.204-223
• /
• 2010

The purpose of this study was to investigate the high temperature creep behavior of anisotropic Zr-2.4%Nb alloy which includes the hydride. To minimize the effect of the anisotropy and to achieve the bi-axial stress condition, SP creep test was performed using the Zr alloys which have the 50 ppm, 100 ppm and 200 ppm hydride. Each SP creep curve was obtained and compared. While the creep degradation of 50 ppm and 100 ppm hydride specimens was clearly found, the degradation of 200 ppm was not cleared. By the comparison of SP creep constant and stree exponent, this fact was confirmed. As the degradation of 50 ppm and 100 ppm hydride was processed, the SP creep constant was decreased and the stress exponet was increased. However, while the SP creep constant of 200 ppm hydride was decreased, the stree exponent was decreased. Finally, it was confirmed that the creep degradation of 200 ppm was not found. In conclusion, the hydride was the major parameter to control the hight temperature creep degradation of Zr alloy.

• Textile Coloration and Finishing
• /
• v.9 no.4
• /
• pp.7-19
• /
• 1997

The purpose of the study was to investigate the shrinkage and creep behavior of PET filaments which were prepared at various spinning speeds(3,300, 4,000, 5,000, 6,000, and 7,000m/min) and anneal($120^{\circ}$, 30min & $150^{\circ}$, 40min). In order to determine the shrinkage and creep behavior with the crystallinity change, PET filaments were treated with low(12$0^{\circ}C$, 30min) and high($150^{\circ}$, 40min) temperature conditions with hot air dryer under the constant tension. The results of the study were as follows: as the spinning speed increased, the degree of shrinkage and elongation of the sample treated by wet condition decreased. The sample with 0.01g/d of load under various spinning speeds showed shrinkage behavior and highest shrinkage ratio at $76^{\circ}$ which was Tg of PET. The degree of shrinkage and elongation of the treated sample was less than those of the untreated sample by wet treatment. Especially, there was less degree of shrinkage and elongation of the sample treated by higher temperature condition. In 3,300m/min of spinning speed the draw ratio of undrawn yarn of a mixture of a-axis orientation and c-axis orientation was 2.0, which is similar to the value of the traditional drawn yarn. Finally, there was a big range of shrinkage and elongation by wet treatment in 3,300 m/min of spinning speed.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.30 no.4
• /
• pp.134-153
• /
• 1988

This paper was carried out to investigate the existence of a unique stress- strain behavior by obtaining some factors influencing the time dependent stress- strain behavior of clay. The results obtained from this study were summarized as follows ; 1. The relationship between stress ratro and strain in normally consolidated clay was in- dependent on pre-shear consolidation pressure. Therefore, shear strain could be expressed as a function with stress ratio. 2. The constitutive equation of shear strain on Modified Carn Clay Model coincided better with the observed value than Cam Clay Model. 3. The relationships between deviator stress and shear strain, between pore water pressure and shear strain were unified by the mean equivalent pressure. 4. The shear strain contour in norrnally consolidated clay was increased linearly through origin, but that in overconsolidated clay was not in accordance with the result of the former. 5. Because the effective stress path of normally consolidated clay was unified by the mean equivalent pressure, state boundary surface in (e,p,q) space was transformed into two dimensional surface. But it was considered to be suitable that the unified stress- strain in overconsolidated clay be expressed by a function with overconsolidation ratio. 6. The deviator for constant strain was increased linearly with increment of strain rate ($\varepsilon$) on semi-log scale, but pore water pressure was decreased. 7. The behavior of stress relaxation was transformed from linear to curvilinear with inc - rement of strain rate before stress relaxation test, and pore water pressure was increased in total range. 8. The strain of creep was increased linearly with increment of time on semi-log scale. The greater the strain rate before creep test became, the greater the increment of strain of creep became. And the pore water pressure during creep test was increased generally with increment of time on semi-log scale.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.136-140
• /
• 2002

High temperature fatigue crack growth behavior of P92 and STS 316L steel were investigated under four load conditions using CT type specimens. Loading and unloading times for the low wave forms were combinations of 1 sec. and 50 sec., which were two symmetric wave forms and two unsymmetric wave forms. Their behaviors are characterized using ΔK parameter. In STS 316L, Crack growth rate generally increases as frequency decreases. However, sensitivity of the loading rate to crack growth rate was fecund to be far greater than that of the unloading time. It is because as loading time increases, creep occurs at crack tip causing the crack growth rate to increase. However creep does not occur at the crack tip even if the unloading time is increased. In P92 steel, crack growth rate showed same behavior as in STS 316L. But the increase in loading or unloading time made almost no difference in crack growth rate, suggesting that no significant creep occurs in P92 steel even though loading time increases. After conducting high temperature tensile tests and comparing high temperature fatigue crack growth rates under various wave forms, it was proved that P92 steel has not only good high temperature properties but also improved, better high temperature fatigue properties than STS 316L.

• Journal of the Korean Society of Safety
• /
• v.27 no.5
• /
• pp.117-125
• /
• 2012

In recent years, polymer concrete based on polyester resin have been widely generalized and the research of polymer concrete have been actively pursued by the technical innovations. Polymer concrete is a composite consisting of aggregates and an organic resin binder that hardens by polymerization. Polymer concrete are stronger by a factor of three or more in compression, a factor of four to six in tension and flexural and a factor of two in impact when compared with portland cement concrete. In view of the growing use of polymer concrete, it is important to study the physical characteristics of the material, emphasizing the short term properties as well as long term mechanical behavior. If polymer concrete is to be used in flexural load-bearing application such as in beam, it is imperative to understand the deformation of the material under sustained loading conditions. This study is proposed to empirical and mechanical model of polymer concrete tension creep using long-term experimental results and mathematical development. The test results showed that proposed model has been used successfully to predict creep deformations at a stress level that was 20 percent of the ultimate strength and viscoelastic behavior of recycled-PET polymer concrete is linear of stress level up to 30 percent. It is expected that the present model allows more realistic evaluation of varying stresses in polymer concrete structures with a constant loading.