• Steel and Composite Structures
• /
• 제31권4호
• /
• pp.409-417
• /
• 2019

The choice of individual material for industrial application is primarily based on knowledge of its behavior in similar applications and similar environmental conditions. Contemporary design implies knowledge of material behavior and knowledge in the area of structural analysis supported by large capacity computers. Bearing this in mind, this paper presents and analyzes the experimental results related to the mechanical properties of the material considered (30CrNiMo8/1.6580/AISI 4340) at different temperatures as well as its creep and fatigue behavior. All experimental tests were carried out as uniaxial tests. The test results related to the mechanical properties are presented in the form of engineering stress-strain diagrams. The results related to the creep behavior of the material are shown in the form of creep curves, while the fatigue of the material is shown in the form of stress - life (S - N) diagram. Based on these experimental results, the values of the following properties are determined: ultimate tensile strength (${\sigma}_{m,20}=696MPa$), yield strength (${\sigma}_{0.2,20}=355.5MPa$), modulus of elasticity ($E_{,20}=217GPa$) and fatigue limit (${\sigma}_{f,20,R=-1}=280.4MPa$). Results related to fatigue tests were obtained at room temperature and stress ratio R = -1.

• 한국지반공학회논문집
• /
• 제19권5호
• /
• pp.291-299
• /
• 2003

본 연구에서는, 토목섬유의 크리프시험시 온도 및 토목섬유에 가해지는 구속응력을 제어할 수 있도록 고안된 온도제어 구속크리프시험(Temperature Dependent Confined Creep Test)을 수행하였다. 시험결과를 토대로, 시험온도 및 구속응력의 크기가 토목섬유의 크리프특성에 미치는 영향을 정량적으로 분석하였으며, 장기적인 크리프변위를 예측하기 위하여 시간-온도 중첩원리를 이용한 합성곡선을 작도하여, 1$\times$$10^7$min.(Geomembrane D)∼1$\times$$10^{10}$min.(Geogrid T)까지의 크리프변위를 예측하였다. 본 합성곡선에 의해, 토목섬유에 가해지는 구속하중에 따른 토목섬유의 이동계수(shift factor)를 도출하였다. 온도제어 구속크리프시험은 시트형 지오그리드와 지오멤브레인을 대상으로 하였으며, 시험온도는 5∼4$0^{\circ}C$의 범위로, 구속하중의 크기는 0∼9t/$cm^2$의 범위로 하였다.

• 소성∙가공
• /
• 제10권5호
• /
• pp.383-388
• /
• 2001

In describing the plastic deformation behaviour of ultrafine-grained materials, a phase mixture model in which a polycrystalline material is regarded as a mixture of a crystalline phase and a grain boundary phase has been successful. The deformation mechanism for the grain boundary phase, which is necessary for applying the phase mixture model to polycrystalline materials, is modelled as a diffusional flow of matter along the grain boundary. A constitutive equation for the boundary diffusion creep of the boundary phase was proposed, in which the strain rate is proportional to (stress/grain siz $e^{2}$). The upper limit of the stress of the boundary phase was set to equal to the strength to the amorphous phase. The proposed model can explain the strain rate and grain size dependence of the strength of the grain boundary phase. Successful applications of the model compared with published experimental data are described.

• Structural Engineering and Mechanics
• /
• 제50권3호
• /
• pp.305-322
• /
• 2014

Reliability-based design limit states and associated partial load factors provide a consistent level of design safety across bridge types and members. However, limit states in the current AASHTO LRFD have not been developed explicitly for the situation encountered by integral abutment bridges (IABs) that have unique boundary conditions and loads with inherent uncertainties. Therefore, new reliability-based limit states for IABs considering the variability of the abutment support conditions and thermal loading must be developed to achieve IAB designs that achieve the same safety level as other bridge designs. Prestressed concrete girder bridges are considered in this study and are subjected to concrete time-dependent effects (creep and shrinkage), backfill pressure, temperature fluctuation and temperature gradient. Based on the previously established database for bridge loads and resistances, reliability analyses are performed. The IAB limit states proposed herein are intended to supplement current AASHTO LRFD limit states as specified in AASHTO LRFD Table 3.4.1-1.

• Geomechanics and Engineering
• /
• 제8권2호
• /
• pp.187-220
• /
• 2015

Soil disturbance induced by installation of mandrel driven vertical drains decreases the in situ horizontal hydraulic conductivity of the soil in the vicinity of the drains, decelerating the consolidation rate. According to available literature, several different profiles for the hydraulic conductivity variation with the radial distance from the vertical drain, influencing the excess pore water pressure dissipation rate, have been identified. In addition, it is well known that the visco-plastic properties of the soil also influence the excess pore water pressure dissipation rate and consequently the settlement rate. In this study, a numerical solution adopting an elastic visco-plastic model with nonlinear creep function incorporated in the consolidation equations has been developed to investigate the effects of disturbed zone properties on the time dependent behaviour of soft soil deposits improved with vertical drains and preloading. The employed elastic visco-plastic model is based on the framework of the modified Cam-Clay model capturing soil creep during excess pore water pressure dissipation. Besides, nonlinear variations of creep coefficient with stress and time and permeability variations during the consolidation process are considered. The predicted results have been compared with V$\ddot{a}$sby test fill measurements. According to the results, different variations of the hydraulic conductivity profile in the disturbed zone result in varying excess pore water pressure dissipation rate and consequently varying the effective vertical stresses in the soil profile. Thus, the creep coefficient and the creep strain limit are notably influenced resulting in significant changes in the predicted settlement rate.

• 대한토목학회논문집
• /
• 제1권1호
• /
• pp.53-68
• /
• 1981

지속하중하(持續荷重下)의 점토지반(粘土地盤) 또는 사면(斜面)을 형성(形成)하고 있는 점토(粘土)는 시간의존변형(時間依存變形)을 일으키고 어떤 경우 파괴(破壞)에 이르기도 하는데 그 원인(原因)은 점토(粘土)의 Creep 거동(擧動) 때문이라는 보고(報告)가 대부분(大部分)이다. Creep 거동(擧動)은 많은 요소(要素)에 관련될 뿐 아니라 특(特)히 함수비(含水比) 및 응력수준(應力水準)에 큰 영향(影響)을 받기 때문에 매우 복잡(複雜)하며 따라서 그 거동(擧動)을 해석(解析) 하기도 어려운 일인데 Creep이 궁극적(窮極的)으로는 점토(粘土) 입자간(粒子間)의 미시적(微視的)인 거동(擧動)에서 비롯되기 때문이다. 응력(應力)-변형(變形)-시간(時間) 관계(關係)로서의 Creep 거동(擧動)을 수학적(數學的)으로 표현(表現)하기 위하여 여러 형태(形態)의 유변학적(流變學的) 모델이 제안(提案) 되었다. 유변학적(流變學的) 모델은 선형(線形) 스프링, 비선형(非線形) Dashpot 및 Slider를 조합(組合)한 것인데 점토(粘土)의 변형(變形)에 관한 탄성적(彈性的), 소성적(塑性的) 및 점성적(粘性的) 성분(成分)을 구분(區分) 하는데 매우 유용(有用)하다. 그러나 대부분(大部分)의 경우, 유변학적(流變學的)모델은 포화(飽和)된 점토(粘土)에 대(對)하여 주(主)로 2차압밀(次壓密) 거동(擧動)을 밝히기 위하여 제안(提案)된 것으로 비포화점토(非飽和粘土)에 대(對)한 보고(報告)는 매우 드문 것 같다. 한편, Creep 거동(擧動)은 시간의존변형(時間依存變形)이므로 흐트러진 점토(粘土)를 다져서 시험(試驗)하는 경우, 시간경과(時間經過)에 따라 Thixotropy 문제(問題)가 제기(提起)될 것이고 배수조건(排水條件)과 관련하여서는 공시체(供試體)의 높이가 문제(問題)될 수 있다. 그뿐 아니라 많은 연구결과(硏究結果)에 의(依)하면 응력증가초기(應力增加初期)에는 시간지체(時間遲滯)가 없는 초기탄성변형(初期彈性變形)이 발생(發生)된다고 하므로 유변학적(流變學的) 모델에는 이를 나타내는 요소(要素)가 반드시 필요(必要)하게 될 것이다. 본(本) 연구(硏究)는 이러한 면(面)에 초점(焦點)을 두고 함수비(含水比)와 응력수준(應力水準)을 여러 가지로 변화(變化)시켰을 때의 Creep 거동(擧動)을 유변학적(流變學的) 모델로 해석(解析)함에 있어 소성(塑性)이 비교적(比較的) 큰 3종(種)의 점토(粘土)를 사용(使用)하여 초기탄성변형(初期彈性變形) 거동(擧動)을 밝히고 Thixotropy 효과(効果) 및 공시체(供試體)의 높이가 Creep 거동(擧動)에 끼치는 영향(影響)을 구명(究明)하며 아울러 유변학적(流變學的) 모델의 어떤 요소(要素)에 관련 되는가를 알아내기 위하여 다져서 성형(成形)한 공시체(供試體)로서 일축배수형식(一軸排水形式)의 Creep 거동(擧動)을 시행(施行)하였다. 실험결과(實驗結果) 및 검토(檢討)에 의(依)하면 응력재하(應力載荷) 및 증가초기(增加初期)에는 시간지체(時間遲滯)가 없는 탄성적(彈性的) 초기변형(初期變形)이 발생(發生)하고 따라서 유변학적(流變學的) 모델에는 이를 나타내기 위한 상부(上部)스프링을 설치(設置)해야 하며 Thixotropy 효과(効果)를 고려(考慮)한 경우, Creep변형(變形)은 완만(緩慢)하게 되나 함수비(含水比) 및 응력수준(應力水準)에 따른 상태거동(狀態擧動)은 같으므로 그 차이(差異)는 모델 상수(常數)의 크기에만 관련됨을 알아내었고 따라서 동일(同一)한 유변학적(流變學的) 모델로 그 거동(擧動)을 나타낼 수 있다는 사실(事實)을 밝혀 냈다. 또 공시체(供試體) 높이를 작게 한 경우에는 함수비(含水比)가 비교적(比較的) 작아서 점(粘)-소(塑)-탄성(彈性) 및 점(粘)-탄성(彈性)일 때만 높이가 클 때와 같은 상태거동(狀態擧動)을 나타내어 동일(同一)한 유변학적(流變學的) 모델로 나타낼 수 있고 함수비(含水比)가 큰 점일소성(粘一塑性) 및 점성류(粘性流)일 때는 그 상태거동(狀態擧動)이 배수문제(排水問題)와 관련하여 달라지게 되고 따라서 유변학적(流變學的) 모델도 달라지게 된다는 사실(事實)을 발견(發見) 하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.143.2-143.2
• /
• 2005

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.365-373
• /
• 2002

For gas turbine engines, the safe life methodology has historically been used fur fatigue life management of failure critical engine components. The safe retirement limit is necessarily determined by a conservative life evaluation procedure, thereby many components which have a long residual life are discarded. The objective of this study is to introduce the damage tolerant design concept into the life management for aircraft engine component instead of conservative fatigue life methodology which has been used for both design and maintenance. Crack growth data were collected on a nickel base superalloy which have been subjected to combined static and cyclic loading at elevated temperatures. Stress analysis fur turbine disk was carried out. The program for computing creep-fatigue crack growth was developed. The residual lifes of turbine disk component under various temperatures and conditions using creep-fatigue crack growth data were estimated. As the result of analysis, it was confirmed that retirement fur cause concept was applicable to the evaluation of residual life of retired turbine disk which had been designed based on the conventional fatigue life methodology.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.390-395
• /
• 2003

This study examined the effects of the testing temperature on the mechanical properties of the stainless steels (STS301CSP-3/4H and STS301CSP-H) for flat spring. Hardness test and fatigue test were performed at room temperature (2$0^{\circ}C$ Tensile testandcreeptestwere performed attemperature range 2$0^{\circ}C$~10$0^{\circ}C$. The micro-victors hardness values of STS301CSP-3/4H and STS301CSP-H were HV=443 and HV=488. respectively. The Elastic modulus, tensile strength, yield strength and strain of these materials were decreased with increasing testing temperature. respectively. The maximum creep strain for 100hr atcreep temperature (10$0^{\circ}C$~20$0^{\circ}C$ and creep stress (Tensile strength$\times$50%) of these materials were 0.53％~0.58%. The fatigue limit of STS301CSP-3/4H and STS301CSP-H were 64.5Kgf/mm$^2$ and 67.4Kgf/mm$^2$, respectively.

• 한국농공학회논문집
• /
• 제52권3호
• /
• pp.73-79
• /
• 2010

In the present study, the loading frequency dependencies of cyclic shear strength and elastic shear modulus of reconstituted clay were examined by performing undrained cyclic triaxial tests and undrained cyclic triaxial tests to determine deformation properties. The result of undrained cyclic triaxial test of reconstituted and saturated clay shows that a faster frequency leads to higher stress amplitude ratio, but when the frequency becomes fast up to a certain point, the stress amplitude ratio will reach its maximum limit and the frequency dependence becomes insignificant. And also, the result of undrained cyclic triaxial deformation test shows a fact that a faster loading frequency leads to higher equivalent shear modules and smaller hysteresis damping ratio, and confirms the frequency dependence of cohesive soil. Meanwhile, the result of the creep test shows that continuing creep is created in the undrained cyclic triaxial test with slow loading frequency rate, and since loading rate becomes slower at the vicinity of the maximum and the minimum deviator stress due to sine wave loading, the vicinity of the maximum and the minimum deviator stress shall be more influenced by creep.