• 대한기계학회논문집A
• /
• 제37권9호
• /
• pp.1127-1132
• /
• 2013

원자로 내부구조물은 파손시 원자로 안전 운전/정지에 주요한 영향을 미칠 수 있으며 중성자 조사 수준이 높아 중성자 조사와 관련된 다양한 열화가 발생하였거나 잠재적으로 발생할 수 있다. 원자로 내부구조물의 주요 재질인 오스테나이트 스테인리스 강은 중성자 조사에 따라 인장/크리프 물성, 파괴인성 등 기계적 재료 거동에 변화가 발생한다. 각종 열화기구에 대한 원자로 내부구조물의 구조 건전성이 설계수명 또는 계속운전 기간 동안 유지됨을 평가할 때 중성자 조사에 따른 기계적 재료거동의 변화를 고려하여야 한다. 본 연구에서는 중성자 조사에 따른 기계적 재료거동의 변화를 고려한 사용자 정의 보조 프로그램을 개발하였다. 개발된 사용자 정의 보조 프로그램을 다양한 조건에 대해 검증한 결과, 타당함을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제65권2호
• /
• pp.129-139
• /
• 2018

Post-tensioning (PT) tendons are commonly used for the assembly of modularized concrete members, and tension is applied to the tendons during construction to facilitate the integrated behavior of the members. However, the tension in a PT tendon decreases over time due to steel corrosion and concrete creep, and consequently, the stress on the anchor head that secures the PT tendon also diminishes. This study proposes an automatic detection system to identify tension reduction in a PT tendon using pulsed-eddy-current (PEC) measurement. An eddy-current sensor is installed on the surface of the steel anchor head. The sensor creates a pulsed excitation to the driving coil and measures the resulting PEC response using the pick-up coil. The basic premise is that the tension reduction of a PT tendon results in stress reduction on the anchor head surface and a change in the PEC intensity measured by the pick-up coil. Thus, PEC measurement is used to detect the reduction of the anchor head stress and consequently the reduction of the PT tendon force below a certain threshold value. The advantages of the proposed PEC-based tension-reduction-detection (PTRD) system are (1) a low-cost (< $ 30), low-power (< 2 Watts) sensor, (2) a short inspection time (< 10 seconds), (3) high reliability and (4) the potential for embedded sensing. A 3.3 m long full-scale monostrand PT tendon was used to evaluate the performance of the proposed PTRD system. The PT tendon was tensioned to 180 kN using a custom universal tensile machine, and the tension was decreased to 0 kN at 20 kN intervals. At each tension, the PEC responses were measured, and tension reduction was successfully detected.

• Asian-Australasian Journal of Animal Sciences
• /
• 제19권6호
• /
• pp.909-914
• /
• 2006

The goal of this study was to investigate the behavior of sows and their piglets reared using the non-all-in all-out system and the all-in all-out system during a 3-week lactation period. The 24 Landrace${\times}$Yorkshire sows (range of parity: 2 to 4) and their litters (range of litter size: 8 to 13 piglets) for each treatment (8 sows/replication) were used in this experiment. The sows were housed in farrowing crates ($0.6{\times}2.1m$) located in pens ($2.4{\times}1.8m$) with totally perforated metal flooring. The crates were kept in an experimental room that was thermostatically controlled to approximately $23^{\circ}C$. A 250-W infrared heat lamp was turned on above the creep area during lactation. The sows and piglets were conventionally managed. The animals were recorded during a 24-h period at 1, 4, 7, 14 and 21 days postpartum. The videotapes were scanned every minute to obtain an instantaneous behavioral sample. In the behaviors of sows, lateral recumbency decreased and ventral recumbency increased from 1 day postpartum to 21 days postpartum. In comparison to the AIAOS, sows in the NAIAOS spent much less time on lateral recumbency (p<0.01), whereas they spent much more time on ventral recumbency and sitting at 4 days postpartum (p<0.05 and p<0.05). In the behaviors of piglets, lying increased and unsuccessful suckling decreased until 21 days postpartum. Compared to the AIAOS at 4 days postpartum, piglets in the NAIAOS spent less time lying (p<0.01), whereas they spent much more time walking and unsuccessful suckling (p<0.01 and p<0.05). These results suggest that the all-in all-out system may be preferable to the non-all-in all-out system for promoting welfare.

• 한국임상보건과학회지
• /
• 제5권4호
• /
• pp.991-997
• /
• 2017

Purpose. The purpose of this study was to muscle properties analysis of SCM(sternocleidomastoid) Muscle according to posture type when using smartphone. Methods. This study was conducted on 73 college students who are using smartphone. Subjects were analyzed myotonPRO to confirm, prone posture group, stand posture group, drop head above $45^{\circ}$in sit posture on a chair group and drop head below $45^{\circ}$in sit posture on a chair group were measured SCM muscle. The myotonPRO were measured one measurer, total 3 times. Comparative analysis of the each groups were investigated of SCM muscle properties. Results. We found that Frequency, Stiffness, Creep and Relaxation were appeared difference in each posture. F index was increased at drop head below $45^{\circ}$group than stand posture group. S index was increased at drop head above $45^{\circ}$group than prone posture group. C index was decreased at drop head below $45^{\circ}$group and drop head above $45^{\circ}$group than prone posture group. R index was decreased at drop head above $45^{\circ}$group than prone posture group. Conclusions. The muscle properties were appeared difference in each posture of SCM muscle using smartphone.

• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1398-1408
• /
• 2003

Tensile and LCF(low cycle fatigue) tests were carried out in air at wide temperature range 20$^{\circ}C$-750$^{\circ}C$ and strain rates of 1${\times}$10$\^$-4//s-1${\times}$10$\^$-2/ to ascertain the influence of strain rate on tensile and LCF properties of prior cold worked 316L stainless steel, especially focused on the DSA(dynamic strain aging) regime. Dynamic strain aging induced the change of tensile properties such as strength and ductility in the temperature region 250$^{\circ}C$-600$^{\circ}C$ and this temperature region well coincided with the negative strain rate sensitivity regime. Cyclic stress response at all test conditions was characterized by the initial hardening during a few cycles, followed by gradual softening until final failure. Temperature and strain rate dependence on cyclic softening behavior appears to result from the change of the cyclic plastic deformation mechanism and DSA effect. The DSA regimes between tensile and LCF loading conditions in terms of the negative strain rate sensitivity were well consistent with each other. The drastic reduction in fatigue resistance at elevated temperature was observed, and it was attributed to the effects of oxidation, creep and dynamic strain aging or interactions among them. Especially, in the DSA regime, dynamic strain aging accelerated the reduction of fatigue resistance by enhancing crack initiation and propagation.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.105-110
• /
• 2000

The Micromechanics test is new test method which uses comparatively smaller specimen than that required in conventional material tests. There are several methods, such as small-specimen creep test, the continuous indentation test, and small punch(SP) test. Among them, the small punch(SP) test method has been applied to many evaluation fields, such as a ductile-brittle transition temperature, stress corrosion cracking, hydrogen embrittlement, and fracture properties of advanced materials like FGM or MMC. In this study, the small punch(SP) test is performed to evaluate the mechanical properties at high/low temperature from $-196^{\circ}C$ to $650^{\circ}C$ and the material degradation for virgin and aged materials of 9Cr1MoVNb steel which has been recently developed. The ${\Delta}P/{\Delta}{\delta}$ parameter defined a slope in plastic membrane stretching region of SP load-displacement curve decreases according to the increase of specimen temperature, and that of aged materials is higher than the virgin material in all test temperatures. And the material degradation degrees of aged materials with $630^{\circ}C$ -500hrs and $630^{\circ}C$ -1000hrs are $36^{\circ}C$ and $38^{\circ}C$ respectively. These behaviors are good consistent with the results of hardness($H_v$) and maximum displacement(${\delta}_{max}$).

• 한국재료학회지
• /
• 제5권7호
• /
• pp.869-879
• /
• 1995

TiAi intermetallic compound has been extensively studied for possible high temperature structural applications because of its high specific strength at high temperature, high creep resistance, and good oxidation resistance at elevated temperatures. In addition to its good properties, an economic manufacturing routes should be developed for this material to be used more extensively. One of the promising route in manufacturing TiAl intermetallics is the Self-propagating High-temperature Synthesis (SHS) method. Thus in this study, an attempt was made to study the mechanism of the SHS process in TiAl synthesis. The composition of the sample was Ti-(45, 50, 53)at% Al and the microstuctures of the products were analyzed using optical microscope and scanning electron microscope. When the phases formed at the main SHS reaction of whicyh combustion temperature is higher than the melting temperature of aluminum were identified as TiAl and Ti$_3$Al ; Ti$_3$Al cores surrounded by TiAl phase. In order to increase the combustion temperature, carbon was added 5 and 10at.%. When the carbon content was 10at.%, the heat of the reaction was large enough to melt the phase formed and that is consistent with the theoretical calculation results of the adiabatic temperature. The combution temperatue, which was measured by a computer data acquisition system, increased with the carbon content. The phases formed from the reaction involving the carbon added were indentified as TiAl and Ti$_2$AlC using XRD. The vickers hardness of the reaction product increased with the carbon content.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.1003-1007
• /
• 1999

This paper is reported for the stability of ZnO-$Pr_{6}O_{11}-CoO-Er_{2}O_{3}$ based ceramic varistors with $Er_{2}O_{3}$ added in the addition range 0.0 to 2.0 mol%. The varistors sintered at $130^{\circ}C$ exhibited abrupt positive current creep phenomena, which accompany thermal run away within short times, even under weak d.c. stress. As a result, these varistors were completely degraded. On the contrary, the stability of varistors sintered at $1350^{\circ}C$ was far better than that of $1300^{\circ}C$. In particular, the varistor containing 0.5 mol% $Er_{2}O_{3}$ showed a excellent stability, which the variation rate of the varistor voltage, the nonlinear coefficient, and leakage current is below 1%, 2%, and 3.5%, respectively, even under more severe d.c. stress, such as ($0.8V_{1mA}/90^{\circ}C/12h$) + ($0.85V_{1mA}/115^{\circ}C/12h$) + ($0.9V_{1mA}/120^{\circ}C/12h$) + ($0.9V_{1mA}/150^{\circ}C/12h$). Consequently, it is estimated that the basic composition of ZnO-$Pr_{6}O_{11}-CoO-Er_{2}O_{3}$ based varistor contain 0.5 mol% $Er_{2}O_{3}$ will be used to the fabrication of the varistors for high performance and stability in a forthcoming.

• International Journal of Fluid Machinery and Systems
• /
• 제2권4호
• /
• pp.269-277
• /
• 2009

The current paper focuses on the analysis of transient cavitating flow in pressurised polyethylene pipes, which are characterized by viscoelastic rheological behaviour. A hydraulic transient solver that describes fluid transients in plastic pipes has been developed. This solver incorporates the description of dynamic effects related to the energy dissipation (unsteady friction), the rheological mechanical behaviour of the viscoelastic pipe and the cavitating pipe flow. The Discrete Vapour Cavity Model (DVCM) and the Discrete Gas Cavity Model (DGCM) have been used to describe transient cavitating flow. Such models assume that discrete air cavities are formed in fixed sections of the pipeline and consider a constant wave speed in pipe reaches between these cavities. The cavity dimension (and pressure) is allowed to grow and collapse according to the mass conservation principle. An extensive experimental programme has been carried out in an experimental set-up composed of high-density polyethylene (HDPE) pipes, assembled at Instituto Superior T$\acute{e}$cnico of Lisbon, Portugal. The experimental facility is composed of a single pipeline with a total length of 203 m and inner diameter of 44 mm. The creep function of HDPE pipes was determined by using an inverse model based on transient pressure data collected during experimental runs without cavitating flow. Transient tests were carried out by the fast closure of the ball valves located at downstream end of the pipeline for the non-cavitating flow and at upstream for the cavitating flow. Once the rheological behaviour of HDPE pipes were known, computational simulations have been run in order to describe the hydraulic behaviour of the system for the cavitating pipe flow. The calibrated transient solver is capable of accurately describing the attenuation, dispersion and shape of observed transient pressures. The effects related to the viscoelasticity of HDPE pipes and to the occurrence of vapour pressures during the transient event are discussed.

• 콘크리트학회논문집
• /
• 제18권4호
• /
• pp.479-487
• /
• 2006

본 연구는 고성능 콘크리트를 사용한 프리텐션 콘크리트 부재에 대한 시간의존거동해석에 관한 연구이다. 일반 콘크리트의 크리프, 건조수축 및 강재의 릴렉세이션 현상에 대한 기존의 AASHTO 방법을 수정하여, 고성능 콘크리트 부재에 대한 단계-함수법 및 시간-단계법에 의한 시간의존 해석기법을 소개하였다. 제시된 모델은 고성능 콘크리트 프리텐션 부재의 프리스트레스 손실 및 처짐에 대한 초기 및 시간의존거동 예측 값을 제공해 준다. 제안된 모델을 이용하여, 고성능 콘크리트를 사용한 프리텐션 부재의 시간의존거동에 관한 실험 결과와 비교하였다. 기존의 AASHTO 규정에 의한 시간의존 거동 예측치에 비해, 소개된 모델에 의한 고성능 콘크리트 부재의 초기 및 시간의존거동 예측결과가 실제 거동에 보다 정확한 결과를 제공해 주었다.