• 한국해안·해양공학회논문집
• /
• 제23권4호
• /
• pp.285-291
• /
• 2011

이 연구에서는 신형소파블록을 대상으로 실험 및 수치해석을 수행하여 역학적 성능을 평가하고 적절한 보강재의 배근에 따른 구조성능 향상 효과를 검토하였다. 수치해석을 통하여 신형소파블록에 인장응력이 발생하는 위치와 크기를 예측하여 보강재를 설계하였다. 보강재로는 일반 철근 및 해양환경에 적합하도록 부식과 피로에 장점을 지닌 섬유보강재(FRP)를 사용하였다. 실험을 통하여 보강재가 없는 무근 신형소파블록의 파괴하중은 350 kN으로 소파블록의 자중에 비하여 6.2배로 나타났으며, 철근이나 FRP보로 보강한 실험체는 모두 실험의 최고하중인 900 kN 이상의 강도를 보였다. 위험단면을 통과하는 보강재의 개수는 시공의 편의를 위해서는 굵은 지름의 단일 보강재를 사용하는 것이 유리하지만 가는 지름의 보강재 여러 개를 사용하여 균열 폭을 감소시키는 것이 바람직하다는 결과를 얻었다.

• 대한안전경영과학회지
• /
• 제19권1호
• /
• pp.15-25
• /
• 2017

The findings were summarized as follows. The safety check by manufacturer showed that 6 of 13 companies are over the average occurrence of defects. It was expected that there would be a difference between manufacturing technology capability and production system of each manufacturer. Consequently, manufacturers should institutionally improve and strengthen certification items for the upward standardization of safety certification before factory. Second, the safety check by year showed that the results of this study accord with those of previous studies on defect time. Consequently, manufacturers should classify the 3-year-old equipment for vehicle-mounted MEWP into a special check subject to do a nondestructive test according to proven results, and also reflect the test in a safety test system to do regular preventive activities of equipment defects. Third, the safety check by part showed that the boom and outrigger parts of vehicle-mounted MEWP have the most defects. Stress concentration resulted in defects as the boom part was most frequently operated in the structural parts for a real work. To prevent this, it is suitable to improve the hardness of boom materials. The outrigger part needs improvement in safety devices with materials. As an outrigger supports the overturning moment of equipment, it is most affected by its load based on the operating radius, resulting in fatigue crack.

• Computers and Concrete
• /
• 제20권4호
• /
• pp.391-407
• /
• 2017

Fiber reinforced polymer (FRP) bars have been recently used to reinforce concrete members in flexure due to their high tensile strength and especially in corrosive environments to improve the durability of concrete structures. However, FRPs have a low modulus of elasticity and a linear elastic behavior up to rupture, thus reinforced concrete (RC) components with such materials would exhibit a less ductility in comparison with steel reinforcement at the similar members. There were several studies showed the behavior of concrete beams with the hybrid combination of steel and FRP longitudinal reinforcement by adopting the experimental and numerical programs. The current study presents a numerical and analytical investigation based on the data of previous researches. Three-dimensional (3D) finite element (FE) models of beams by using ANSYS are built and investigated. In addition, this study also discusses on the design methods for hybrid FRP-steel beams in terms of ultimate moment capacity, load-deflection response, crack width, and ductility. The effects of the reinforcement ratio, concrete compressive strength, arrangement of reinforcement, and the length of FRP bars on the mechanical performance of hybrid beams are considered as a parametric study by means of FE method. The results obtained from this study are compared and verified with the experimental and numerical data of the literature. This study provides insight into the mechanical performances of hybrid FRP-steel RC beams, builds the reliable FE models which can be used to predict the structural behavior of hybrid RC beams, offers a rational design method together with an useful database to evaluate the ductility for concrete beams with the combination of FRP and steel reinforcement, and motivates the further development in the future research by applying parametric study.

• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.231-254
• /
• 1994

Fracture of cusp, on posterior teeth, especially those carious or restored, is major cause of tooth loss. Inappropriate treatments, such as unnecessarily wide cavity preparations, increase the potential of further trauma and possible fracture of the remaining tooth structures. Fracture potential may be directly related to the stresses exerted upon the tooth during masticatory function. The purpose of this study is to evaluate the fracture resistance of tooth, restored with composite resin inlay. In this study, MOD inlay cavity prepared on maxillary first premolar and restored with composite resin inlay. Three dimensional finite element models with eight nodes isoparametric solid element, developed by serial grinding-photographing technique. These models have various occlusal isthmus and depth of cavity, 1/2, 1/3 and 1/4 of isthmus width and 0.7, 0.85 and 1.0 of depth of cavity. The magnitude of load was 474 N and 172 N as presented to maximal biting force and normal chewing force. These loads applied onto ridges of buccal and lingual cusp. These models analyzed with three dimensional finite element method. The results of this study were as follows : 1. There is no difference of displacement between width of occlusal isthmus and depth of cavity. 2. The stress concentrated at bucco-mesial comer, bucco-disal comer, pulpal line angle and the interface area between internal slopes of cusp and resin inlay. 3. The vector of stress direct to buccal and lingual side from center of cavity, to tooth surface going on to enamel. The magnitude of vector increase from occlusal surface to cervix. 4. The crack of tooth start interface area, between internal slop of buccal cusp and resin inlay. It progresses through buccopulpal line angle to cervix at buccomesial and buccodistal comer. 5. The influence with depth of cavity to fracture of tooth was more than width of isthmus. 6. It would be favorable to make the isthmus width narrower than a third of the intercuspal distance and depth of cavity is below 1 : 0.7.

• 소성∙가공
• /
• 제24권3호
• /
• pp.205-211
• /
• 2015

The current investigation was performed to study sliding-wear-rate deviation (wear-rate data scatter) in carbon steels with various microstructures. Pure iron, 0.2 wt. % C steel, 0.45 wt. % C steel, and bearing steel (AISI52100) were used for the investigation. These steels possess different microstructures. Microstructures of the pure iron, two carbon steel and the bearing steel were full ferrite, ferrite + pearlite and full pearlite, respectively. Depending on the carbon content, the carbon steel had different pearlite-volume fractions. Dry sliding wear tests of the steel were conducted using a ball-on-disk wear tester at a sliding speed of 0.1 m/s using a bearing ball (AISI52100) as a counterpart. Applied load and sliding distance were 100 N and 300 m, respectively. More than three (up to twelve) tests were conducted for each steel under the same conditions, and the mean deviations in the wear rate of the steel (microstructure) were compared. The wear-rate deviation in the steel with ferrite + pearlite microstructure was higher than that with ferrite microstructure, and the deviation decreased with the increase of pearlite volume fraction. The pure iron and the bearing steel specimens showed much less deviation. The high deviation observed from the ferrite + pearlite steel was attributed to irregular subsurface-crack nucleation and growth at the interface between the two micro constituents (ferrite and pearlite) during the wear test.

• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.1015-1022
• /
• 2001

The objective of this paper is to develop an expert system called NPIES for nuclear piping integrity. This paper describes the structure and the development strategy of the NPIES system. The NPIES system consists of 3 part; the data input part, the analysis part and the output part. The data input part consists of the material properties database module and the suer interface module. The analysis part consists of the LEFM, CDFD, J/T, limit load modules and the 12 analysis routines for different cracks and loading conditions are provided respectively. Analysis results are presented to screen, printer and text file in the output part. Several case studies on circumferentially cracked piping were performed to evaluate the accuracy and the usefulness of the code. Maximum piping loads predicted by the NPIES system agreed well with those by the 3-dimensional finite element analysis. In addition, even if the material properties were not fully given, the NPIES system provided reasonable evaluation results with the predicted material properties inferred from the material properties database module.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권4호
• /
• pp.20-27
• /
• 2021

이 연구에서는 강봉 트러스 시스템으로 보강된 조적벽체의 내진거동을 합리적으로 평가하기 위하여 범용프로그램인 Abaqus를 이용한 비선형 유한요소해석 절차를 제시하였다. 조적벽체의 유한요소 모델은 콘크리트 손상 소성(concrete damaged plasticity, CDP)모델 및 벽돌-모르타르 계면 특성은 Yang et al.이 제시한 조적 프리즘의 압축 및 인장의 응력-변형률 모델과 전단마찰모델을 기반으로 메소-스케일법을 적용하였다. 유한요소 해석결과를 다양한 변수조건에서 실험결과와 비교한 결과, 강봉 트러스 시스템으로 보강된 조적벽체의 균열진전, 파괴 모드, 강체회전 내력 및 최대내력 그리고 횡하중-횡변위 관계에 대한 실험결과와 잘 일치하였다. 따라서 제시된 유한요소해석 절차는 조적벽체의 내진보강 설계에 합리적으로 이용될 수 있다고 판단된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권1호
• /
• pp.85-93
• /
• 2019

프리캐스트 바닥판 공법은 바닥판간 이음부가 존재하며, 이음부의 연결성능에 따라 전체 교량 구조물의 성능이 좌우되므로 이음부의 연결성능 확보가 중요한 요소이다. 특히, 교량바닥판은 차량하중과 같은 반복하중을 받는 구조물이므로 피로하중에 대한 이음부의 거동 및 성능평가가 이루어져야 한다. 본 연구에서는 비대칭 요철형 루프이음을 적용한 2거더 연속합성형 교량을 제작하여 정적 및 200만회 반복하중의 피로실험을 통해 프리캐스트 바닥판의 구조적 거동 및 균열양상을 검토하였다. 실험결과, 제안된 프리캐스트 바닥판 연결시스템은 균열 폭, 누수, 인장철근의 응력 등 충분한 피로성능 및 파괴강도를 확보하는 것으로 나타났으며, 프리캐스트 바닥판 이음부에 효과적으로 적용 가능할 것으로 판단된다.

• Advances in concrete construction
• /
• 제7권2호
• /
• pp.117-126
• /
• 2019

When designing reinforced concrete (RC) members, the rebar is assumed to resist all tensile forces, but the resistance of the concrete in the tension area is neglected. However, concrete can also resist tensile forces and increase the tensile stiffness of RC members, which is called the tension stiffening effect (TSE). Therefore, this study assessed the TSE, particularly after yielding of the steel bars and the effects of the steel ratio on the TSE. For this purpose, RC member specimens with steel ratios of 2.87%, 0.99%, and 0.59% were fabricated for uniaxial tensile tests. A vision-based non-contact measurement system was used to measure the behavior of the specimens. The cracks on the specimen at the stabilized cracking stage and the fracture stage were measured with the image analysis method. The results show that the number of cracks increases as the steel ratio increases. The reductions of the limit state and fracture strains were dependent on the ratio of the rebar. As the steel ratio decreased, the strain after yielding of the RC members significantly decreased. Therefore, the overall ductility of the RC member is reduced with decreasing steel ratio. The yielding plateau and ultimate load of the RC members obtained from the proposed equations showed very good agreement with those of the experiments. Finally, the image analysis method was possible to allow flexibility in expand the measurement points and targets to determine the strains and crack widths of the specimens.

• Composites Research
• /
• 제32권1호
• /
• pp.6-12
• /
• 2019

본 논문에서는 Cross-ply 탄소섬유/에폭시 복합재 적층판의 모드 I 층간분리 특성을 분석하였다. 이를 위하여 Cross-ply 시편에 대한 Double-Cantilever Beam(DCB) 시험을 수행하였다. Cross-ply DCB 시편의 경우 층간 및 층내 파괴를 포함한 복합적인 균열 성장과 기하학적 대변형에 의한 비선형성을 수반하였다. 따라서 변형률 에너지 해방률과 유한요소해석을 기반으로 비선형성을 수반한 DCB 시험에서도 적용되는 모드 I 층간 파괴인성 평가방법을 제안하고 기존의 선형이론으로 구한 결과와 비교 분석하였다. 본 연구에서 제안한 방법으로 Cross-ply DCB 시편의 모드 I 층간 파괴인성과 모드 I 층내 파괴인성을 분류하였고 모드 I 층내 파괴인성이 더욱 낮음을 확인하였다.