• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.4
• /
• pp.40-47
• /
• 2022

The present study aimed to examine the effectiveness of different techniques for controlling the diagonal cracks at the corners of openings on the strength, deformation, and crack propagation in reinforced concrete walls. The crack control strip proposed in this study, the conventional diagonal steel reinforcing bars, and stress-dispersion curved plates were investigated for controlling the diagonal cracks at the opening corners. An additional crack self-healing function was also considered for the crack control strip. To evaluate the volume change ratio and crack width propagation around the opening, downsized wall specimens with a opening were tested under the diagonal shear force at the opening corner. Test result showed that the proposed crack control strip was more effective in reducing the volume change and controlling the crack width around the opening when compared to the conventional previous methods. The crack control strip with crack healing feature displayed the superior performance in improving the strength of the wall and reducing the crack width while healing cracks occurred in the previous tests.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.683-686
• /
• 2005

This paper is related to investigate adding effect of fluorine-silicate hybrid type crack controlling agent(FS) on initial behavior, dynamic properties, adibatic hydration temp, and plastic crack behavior of concrete(Specification : 25-30-18). It is appeared that adding of FS contributed to strength elevation, lowering of hydration temperature as well as plastic crack reduction without disturbance of initial behaviors of concrete such as slump, air content and setting.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.266-272
• /
• 2002

This study reviews the factors controlling the weld metal cracking and shows the difference from those of HAZ cracking. It further reviews the recent progresses made in consumable design for improving the crack resistance in the high strength weld metal. Previously the controlling factors for weld metal cracking were regarded as weld metal strength, diffusible hydrogen and weld metal height. However an overall review presented in this article shows that the cold crack resistance can be improve significantly through the microstructural control and that an increase in tensile strength is not necessarily related to a decrease in the resistance to cold cracking.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.1
• /
• pp.30-36
• /
• 2009

Cracking of scored or creased lines on boards is a serious problem in converting process of corrugated fiberboard. It is important to reduce the possibility of score crack in advance by controlling the related quality factors of linerboard. To find out the key properties affecting score crack, we carried out the correlation analysis between score crack and physical properties of linerboards. Score crack was evaluated by visual rating on surface crack after folding a linerboard using laboratory folding resistance tester. Thickness of linerboard was the most important factor to score crack. The critical limits of thickness and strain can be determined by correlation analysis for reducing the possibility of score crack.

• Journal of the Korea Concrete Institute
• /
• v.23 no.4
• /
• pp.471-478
• /
• 2011

For a practical simplicity in designing of reinforced concrete structures, the indirect crack controlling method of limiting bar spacing is adopted in KCI structural design provisions. In addition, a direct method for evaluating crack width is also provided in the appendix of the code. But there may be some mismatched results between these two crack controlling methods. In this study, limit values of maximum bar spacing calculated from KCI provisions, KCI appendix, and Frosch's equation are examined as concrete strength, cross-section height, and concrete cover are varied, and the differences are analyzed. From the results, it becomes clear that the differences between maximum bar spacing calculated from KCI code text provisions and those from KCI code appendix provisions are too significant to be neglected. Therefore, rational crack models are suggested in order to get rid of the discrepancy between the direct and indirect control methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.704-708
• /
• 1996

The elastic dynamic crack curving could be obtained by controlling the loading rate, the initial crack-tip blunting to store much energy before crack initiation and the magnitude of reflected wave from finite boundaries. However there is no theoretical and experimental elastic-plastic dynamic curving study. This paper proposes a specimen geometryfor a study of dynamic elastic-plastic crack curving and presents a preliminary result. The specimen has a blunt physical crack tip on a side, and a round notch tip on the other side. From the experiment using this specimen, it is found that the narrow plastic zone ahead of the round notch tip produces the change of load direction and anti-symmetricity of the dynamic isochromatics, and each result causes the crack curving phenomenon. After a certain time, as the elastic-plastic crack gets close to the round notch tip near, the degree of the crack curving get larger. The elastic reack curving propagates more sensitively to the surround of crack tip than the plastic crack curving does. The cynamic elastic-plastic crack curving is found to be proportional to the CTOA(the crack tip opening angle). The dynamic elastic-plastic crack may propagate in the direction perpendicular to the loading. An apparant strip yield zone which is similar to the Dugdale strip yield zone is noted ahead of the physical crack tip.

• Journal of Mechanical Science and Technology
• /
• v.16 no.1
• /
• pp.39-45
• /
• 2002

Initiation and propagation of interfacial crack along bimaterial interface are considered in this study. A biaxial loading device for a single specimen is used for obtaining a wide range of mode-mixities. The specimen is an edge-cracked bimaterial strip of glass and epoxy; the biaxial loading device, being capable of controlling displacements in two perpendicular directions, is developed. A series of interfacial crack initiation and Propagation experiments are conducted using the biaxial loading device for various mixed modes. Normal crack opening displacement (NCOD) is measured near crack front by a crack opening interferometry and used for extracting fracture parameters. From mixed mode interfacial crack initiation experiments, large increase in toughness with shear components is observed. The behavior of interfacial crack propagation analyzed as a function of mode-mix shows that initial crack propagation is delayed with increase of mode-mixity, and its velocity is increased with positive mode-mixity but decreased with negative case. However, it is found that crack propagation is less accelerated with positive mode-mixity than the negative mode-mixity, which may be caused by contact and/or effects of friction between far field and near-tip Held along the interfacial crack.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.4
• /
• pp.428-433
• /
• 2015

A non-symmetric laser beam was used for cutting a thin glass substrate and its effect was investigated. In laser cutting of brittle materials, controlling crack initiation on the surface is crucial; however, it is difficult to ensure that crack propagation occurs according to a designed laser path. A lot of deviation in crack propagation, especially at the edge of the substrate, is usually observed. A non-symmetric laser beam generates a non-uniform energy distribution, which enhances directional crack propagation. A 20-W pulsed YAG laser was used for cutting a thin glass substrate. Parametric analysis was carried out and the crack control of the non-symmetric laser beam was improved. A theoretical model was presented and the limitations of the proposed process were also discussed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.1 s.71
• /
• pp.15-25
• /
• 2006

The researches on the early-aged concrete hydration process and the techniques for the early-aged concrete crack control mainly have been focused and developed on the massive concretes in both experimental and numerical studies. However, those researches for relatively thin members such as the upper slab of the reinforced concrete rahmen bridge have nearly been attempted. In this study, a designing technique for crack controlling in the thin members of the early-aged reinforced concrete rahmen bridges based on measured temperature history, strength revelation model and sinkage model is proposed. A method of calculating the reinforcing bar area for crack controlling is also proposed and it is found that the distributing bars under the design loads become the main reinforcing bars in the temperature stress analysis of the early-aged reinforced concrete rahmen bridges. It is shown that the proposed analysis technique is able to use the design of crack control for the early-aged reinforced concrete rahmen bridge.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.617-620
• /
• 2006

This study is related to comprehending performance for watertightness and crack control of concrete added with crack reducing agent concerning to high strength concrete mixs. It was confirmed that watertightness of concrete added with agent could be improved by evaluation absorption ratio, permeability ratio and pore size distribution of hardened concrete. As well resistance to crack resulted from shrinkage was transferred to better state by the addition of agent.