• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1393-1398
• /
• 2009

Conventionally, etching is first considered for microelectronics fabrication process and is specially important in process of a-Si:H thin film transistor for LCD. In this paper, we stabilize properties of device by development of wet and dry etching process. The a-Si:H TFTs of this paper is inverted staggered type. The gate electrode is lower part. The gate electrode is formed by patterning with length of 8 ${\mu}$m${\sim}$16 ${\mu}$m and width of 80${\sim}$200 ${\mu}$m after depositing with gate electrode (Cr) 1500 ${\AA}$under coming 7059 glass substrate. We have fabricated a-SiN:H, conductor, etch-stopper and photo resistor on gate electrode in sequence, respectively. The thickness of these thin films is formed with a-SiN:H (2000 ${\mu}$m), a-Si:H(2000 ${\mu}$m) and n+a-Si:H (500 ${\mu}$m), We have deposited n-a-Si:H, NPR(Negative Photo Resister) layer after forming pattern of Cr gate electrode by etch-stopper pattern. The NPR layer by inverting pattern of upper gate electrode is patterned and the n+a-Si:H layer is etched by the NPR pattern. The NPR layer is removed. After Cr layer is deposited and patterned, the source-drain electrode is formed. In the fabricated TFT, the most frequent problems are over and under etching in etching process. We were able to improve properties of device by strict criterion on wet, dry etching and cleaning process.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.6
• /
• pp.263-267
• /
• 2006

As technology advances, there is a demand for development of hard solid lubricant coating. (Ti, Cr, Zr)N-$MoS_2$ films were deposited on AISI H13 tool steel substrate by co-deposition of $MoS_2$ with (Ti, Cr, Zr)N using a D.C. magnetron sputtering process. The influence of the $N_2Ar$ gas ratio, the amount of $MoS_2$ in the films and the bias voltage on the mechanical and structural properties of the films were investigated. The highest hardness level was observed at the $N_2/Ar$ gas ratio of 0.3. Hardness of the films did not change much with the increase of the $MoS_2$ content in the films. As the substrate bias potential was increased, hardness level of the film reached maximum at -150 V. Surface morphology of these films indicated that high hardness was attributed to the fine dome structure.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.6
• /
• pp.298-304
• /
• 2009

The effect of the surface treatments on the high temperature properties of the Inconel 617, one of the promising candidate alloys for high temperature heat-transport system, has been studied. Various surface modification methods including a rapid thermal process(RTP), a hydrothermal treatment, and a physical vapor deposition($2{\mu}m$ thick TiAlN film by an arc discharge) were applied to the Inconel 617. The morphological and the structural properties of the surface-modified Inconel 617 samples after heat treatment at $1000^{\circ}C$ in the air were compared to find out whether inhomogeneous formation of $Cr_2O_3$ crust at the surface region was suppressed or not. TiAlN-coated Inconel 617 showed homogeneous microstructure and the lowest wear loss compared to bare, RTP- and hydrothermally-treated Inconel 617 by suppressing the $Cr_2O_3$ crust formation.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.1
• /
• pp.33-38
• /
• 2002

For the evaluation of nucleation and growth behaviors influenced by substrate properties, such as surface energy, structure and electrical properties, chromium nitride films (CrN) were deposited on various substrates (glass, AISI 1040 steel and Si (110) by unbalanced magnetron sputtering. X-ray diffraction and Atomic Force Microscopy (AFM) were used to study the microstructure and grain growth as a function of deposition time. The diffraction patterns of CrN thin films deposited on Si (110) exhibited crystalline structure with highly preferred orientation of (200) plane parallel to the substrate, whereas the films deposited on glass and AISI 1040 exhibited preferred orientations (200) and minor orientation (111), (311) or (220) plane. The orientation of films deposited both on glass and Si substrates did not depend on the bias voltage (Vs). The grain growth and structure of film deposited on AISI 1040 steel substrate are strongly influenced by the substrate bias in comparison with that deposited onto glass and Si substrates. The differences in the structure and grain growth of CrN films deposited onto different substrates are predominantly related to the properties of the substrate (structure and electrical conductivity).

• The korean journal of orthodontics
• /
• v.51 no.4
• /
• pp.270-281
• /
• 2021

Objective: The aim of this in vitro study was to evaluate the changes in friction between orthodontic brackets and archwires coated with aluminum oxide (Al₂O₃), titanium nitride (TiN), or chromium nitride (CrN). In addition, the resistance of the coatings to intraoral conditions was evaluated. Methods: Stainless steel canine brackets, 0.016-inch round nickel-titanium archwires, and 0.019 × 0.025-inch stainless steel archwires were coated with Al₂O₃, TiN, and CrN using radio frequency magnetron sputtering. The coated materials were examined using scanning electron microscopy, an X-ray diffractometer, atomic force microscopy, and surface profilometry. In addition, the samples were subjected to thermal cycling and in vitro brushing tests, and the effects of the simulated intraoral conditions on the coating structure were evaluated. Results: Coating of the metal bracket as well as nickel-titanium archwire with Al₂O₃ reduced the coefficients of friction (CoFs) for the bracket-archwire combination (p < 0.01). When the bracket and stainless steel archwire were coated with Al₂O₃ and TiN, the CoFs were significantly lower (0.207 and 0.372, respectively) than that recorded when this bracket-archwire combination was left uncoated (0.552; p < 0.01). The friction, thermal, and brushing tests did not deteriorate the overall quality of the Al₂O₃ coatings; however, some small areas of peeling were evident for the TiN coatings, whereas comparatively larger areas of peeling were observed for the CrN coatings. Conclusions: Our findings suggest that the CoFs for metal bracket-archwire combinations used in orthodontic treatment can be decreased by coating with Al₂O₃ and TiN thin films.

• Journal of the Korean Vacuum Society
• /
• v.15 no.1
• /
• pp.110-116
• /
• 2006

The mechanical property and cutting performance of the cutting tools coated with nanoscale nyktukatered nitride film have been investigated. $Ti_{0.54}Al_{0.46}N-CrN$ and $Ti_{0.84}Al_{0.16}N-NlN$ systems, which showed super-lattice in nanoscale multilayered coating, were deposited on WC-Co insert by UBM sputtering, The superlattice coatings with different bilayer periods were manufactured by controlling deposition parameters. The superlattice formation and hardness of the nanoscale multilayered nitride film and the cutting performance of the insert coated with the film were examined. The hardness and cutting performance were dependent on the bilayer periods of the coatings. The flank wear of the inserts with superlattice coatings were decreased over $20\%$, compared to those of commonly used cutting tools coated with TiAIN single phase.

• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1052-1057
• /
• 1997

현재 전기, 전자, 우주, 자동차, 무기 등의 여러 분야에서 응용되고 있는 TaNx 다층박막저항체의 특성을 개선하기 위하여 magnetron sputtering법으로 TaNx박막을 제조한 후, 온도와 질소분압에 따른 전기저항 및 TCR특성 변화를 조사하였고, 미세조직이 이들 전기적 성질에 미치는 영향을알아보기 위해 상분석과 morphology를 관찰하였다. 그 결과, TaNx을 코팅한 박막의 전기저항은 $N_{2}$Ar이 0.4 이상에서, 금속전도특성에서 이온전도특성으로 변화하였으며,Cr이 TCR효과를 안정시키는 역할은 하여 TaNx/A $I_{2}$ $O_{3}$보다 TaNx/Cr/A $i_{2}$ $O_{3}$박막의 TCR특성이 더 안정하게 나타났다. 또한 TaNx/A $I_{2}$ $O_{3}$박막과 TaNx/Cr/A $i_{2}$ $O_{3}$박막의 경우 모두 $N_{2}$/Ar이 0-0.4정도에서 TCR효과에 좋은 특성을 나타내었다. X-선회절 실험 결과 $N_{2}$/Ar비가 1일 경우에 T $a_{2}$ $N_{.8}$이 생성되었고, 분압이 증가함에 따라 비정질이 생성되었다. morphology가 $N_{2}$/Ar이 증가함에 따라 입자의 모양이 불연속아일랜드 형태로 변화하였으며, 이것은 질소분압에 따른 전기저항 변화와 일치하였다.다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.475-480
• /
• 2018

We investigated the tribological properties of amorphous carbon (a-C) films deposited with CrC interlayers of various thicknesses as the adhesive layer. A-C and CrC thin films were deposited using the unbalanced magnetron (UBM) sputtering method with graphite and chromium as the targets. CrC films as the interlayer were fabricated under a-C films, and various structural, surface, and tribological properties of a-C films deposited with various CrC interlayer thicknesses were investigated. With various CrC interlayer thicknesses under a-C films, the tribological properties of CrC/a-C films were improved; the increased film thickness exhibited a maximum high hardness of over 27.5 GPa, high elastic modulus of over 242 GPa, critical load of 31 N, residual stress of 1.85 GPa, and a smooth surface below 0.09 nm at the condition of 30-nm CrC thickness.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.100-102
• /
• 2013

Magnetron-sputtering법을 사용하여 기존에 연구하였던 CrAlN (Cr 7：Al 3)박막에 Si를 첨가하여 Si의 함량 변화에 따라 미세구조와 화학적 결합상태, 온도저항계수(TCR) 및 산화저항의 영향과 기계적특성 개선을 통한 multi-functional heater resistor layer로써의 가능성을 연구하였다. CrAlSiN 박막의 Si 함량에 변화에 따라 온도저항계수 변화를 확인하였으며 X-선 회절 분석(XRD) 패턴 분석결과 CrAlSiN 박막의 결정구조가 Bl-NaCl 구조를 가지고 있는 것을 확인하였으며 SEM과 AFM을 통한 표면 및 미세구조 분석결과 Si의 함량이 증가할수록 입자가 조밀해짐을 알 수 있었다. 최근 digital priting technology의 핵심 기술로 부각되고 있는 inkjet priting technology는 널리 태양전지뿐만 아니라 thin film process, lithography와 같은 반도체 공정 기술에 활용 할 수 있기 때문에 반도체 제조장비에도 사용되고 있으며, 현재 thermal inkjet 방식을 사용하고 있다. Inkjet printing technology는 전기 에너지를 잉크를 배출하기 위해 열에너지로 변환하는 thermal inkjet 방식을 사용하고 있는데, 이러한 thermal inkjet 방식은 기본적으로 전기저항이 필요하지만 electrical resistor layer는 잉크를 높은 온도에서 순간적으로 가열하기 때문에 부식이나 산화 등의 문제가 발생할 수 있어 이에 대한 보호층을 필요로 한다. 하지만, 고해상도, 고속 잉크젯 프린터, 대형 인쇄 등을 요구되고 있어 저 전력 중심의 잉크젯 프린터의 열효율을 방해하는 보호층 제거에 필요성이 제기되고 있다. 본 연구는 magnetron-sputtering을 사용하여 기존의 CrAlN 박막에 Si를 합성하여 anti-oxidation, corrosion resistance 그리고 low temperature coefficient of resistance 값을 갖는 multi-functional heater resistor layer로써 CrAlSiN 박막의 Si 함량에 따른 효과에 초점을 두었다. 본 실험은 CrAlN 박막에 Si 함량을 4~11 at%까지 첨가시켜 함량의 변화에 따른 특성변화를 확인하였다. 함량이 증가할수록 amorphous silicon nitride phase의 영향으로 박막의 roughness는 감소하였으며 XRD 분석결과 (111) peak의 Intensity가 감소함을 확인하였으며 SEM 관찰시 모든 박막이 columnar structure를 나타내었으며 Si함량이 증가할수록 입자가 치밀해짐을 보여주었다.Si함량이 증가할수록 CrAlN 박막에 비하여 면저항은 증가하였으며 TCR 측정결과 Si함량이 6.5 at%일 때 가장 안정한 TCR값을 나타내었다. Multi-functional heater resistor layer 역할을 하기 위해서, CrAlSiN 박막의 원소 분포, 표면 거칠기, 미세조직, 전기적 특성 등을 조사하였다. CrAlN 박막의 Si의 첨가는 크게 XRD 분석결과 주상 성장을 억제 할 수 있으며 SEM 분석을 통하여 Si 함량이 증가할수록 Si3N4 형성이 감소하며 입자크기가 작아짐을 확인하였다. 면저항의 경우 Si 함량이 증가함에 따라 높은 면저항을 나타내었으며 Si함량이 6.5 at%일 때 가장 낮은 TCR 값인 3120.53 ppm/K값을 보였다. 이 값은 상용되고 있는 heater resistor보다 높지만, CrAlSiN 박막이 더 우수한 기계적 특성을 가지고 있기 때문에 hybrid heater resistor로 적용할 수 있을 것으로 기대된다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.15-16
• /
• 2000

The gate bias stress effect of the hydrogenated amorphous silicon (a-Si:H) thin-film transistors (TFTs) with a $SiN_x/BCB$ gate insulator have been studied. The gate planarization was carried out by spin-coating of BCB (benzocyclobutene) on Cr gates. The BCB exhibits charge trappings during a high gate bias, but the stability of the TFT is the same as conventional one when it is between -25 V and +25 V. The charge trap density in the BCB increases with its thickness.