• 한국표면공학회지
• /
• 제28권3호
• /
• pp.142-151
• /
• 1995

In this research, a thin layer of Cr was coated on the pure Ni and Inconel 601 by PECVD (Plasma Enhanced Chemical Vapor Deposition) in order to study the effect of Cr on the oxidation behavior at high temperature. Cr coated Inconel 601, which was oxidized at $1100^{\circ}C$ for 24 hours, formed a protective $Cr_2O_3$ oxide layer and the resistance to isothermai oxidation was improved. On the other hand, oxidation resistance of Cr coated Inconel 601 at 100$0^{\circ}C$ was not significantly improved, probably due to the formation or insufficient $Cr_2O_3$ layer. But, when oxidized at $1000^{\circ}C$ and $1100^{\circ}C$ for 100 hours, Cr coated Inconel 601 improved isothermal oxidation resistance by the formation of continuous $Cr_2O_3$ external scale and by the development of $Al_2O_3$ subscales. Cr coated Ni formed inner layer of $Cr_2O_3$ within almost pure NiO, which provided additional cation vacancies, thus increasing the mobility of Ni ions in this region. It is believed that this doping effect resulted in an increase in the observed oxidation rate compared with pure Ni and did not improve the oxidation resistance.

• 한국세라믹학회지
• /
• 제22권6호
• /
• pp.37-41
• /
• 1985

Several $Al_2O_3$-based polycrystalline which had different dopant ratio in the range of 0.5mol% were prepared by doping pure $Cr_2O_3$, $ZrO_2$, $HfO_3$ Single crystalline which had same composition with above polycrystalline were made by means of floating zone method. This study examined the role of each dopant for enhancing the mefchanical properties of $Al_2O_3$-based Ceramics. Optical micrographs $({\times}200)$ of $Al_2O_3-Cr_2O_3$ single crystal showing not only radial crack (rc) on the specimen surface but median crack (mc) and lateral crack (lc) under surface at the edge of indentation mark. Fracture toughness of $Al_2O_3$-based Ceramics was increased with $ZrO_2$ content. Alloying effect of $Cr_2O_3$ contributed to the hardness of $Al_2O_3$ based ceramics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.623-626
• /
• 2004

[ $Ba_{0.6}Sr_{0.4}TiO_3$ ] (BST) dielectric thin films doped by Cr were prepared using an alkoxide-based sol-gel method on the Pt/Ti/SiO2/Si substrate. Atomic force microscopy and x-ray diffraction analysis showed that increasing the Cr doping ratio causes increased grain size while the surface remains smooth and crack-free. It was also found that compared with undoped films the increase of Cr content in BST improves the dielectric constant and the leakage-current characteristics. The figure of merit reached the maximum value of 72.3 at the 5 mol % of Cr doping. This composition showed the dielectric constant of 426, the loss factor of 0.0065, tenability of 47.7%, and leakage-current density (at the electric field of 100 kV/cm) of $5.31{\times}10^{-8}A/cm^2$. The results show that the Cr-doped BST thin films are prospective candidates for applications in tunable devices.

• 센서학회지
• /
• 제29권2호
• /
• pp.112-117
• /
• 2020

Xylene is a hazardous volatile organic compound that should be precisely measured to monitor indoor air quality. However, the selective and sensitive detection of ppm-level xylene using oxide-semiconductor gas sensors remains a challenge. In this study, pure and Cr-doped Co₃O₄ nanoparticles (NPs) were prepared using flame spray pyrolysis, and their gas-sensing characteristics to 5-ppm xylene at 250 ℃ were investigated. The 4 at% Cr-doped Co₃O₄ NPs exhibited a high gas response to 5-ppm xylene (resistance ratio to gas and air = 39.1) and negligible cross-responses to other representative and ubiquitous indoor pollutants such as ethanol, benzene, formaldehyde, carbon monoxide, and ammonia. In this paper, the enhancement of the gas response and selectivity of Co₃O₄ NPs to xylene by Cr doping was discussed in relation to the catalytic promotion of the gas-sensing reaction. This sensor can be used to monitor indoor xylene.

• 한국세라믹학회지
• /
• 제37권12호
• /
• pp.1159-1164
• /
• 2000

페롭스카이트 구조를 갖는 E $r_{1-x}$S $r_{x}$Cr $O_{3-y}$ 계에서 x=0.0, 0.05, 0.1, 0.2인 비화학양론적 화합물 고용체를 1573 K 대기압 하에서 제조하였다. X-선 회절분석을 통하여 제조된 모든 계들이 등방정계 단일상을 형성하였고, 또한 반지름이 큰 S $r^{2+}$를 doping 시켜줌에 따라 격자상수 및 환산부피가 증가됨을 알 수 있었으며, 단위 세포의 부피는 직선성을 보이며 증가하였다. TG-DTA에 따른 열분석 결과 Sr이 치환되지 않은 계에서는 상전이가 발생하는 반면, x값이 0.05 이상인 계들은 고온영역에 이르기까지 등방정계에서 마름모정계로의 상전이가 억제되었다. 전자현미경을 통하여 치환된 Sr의 몰비에 따른 시료들이 미세구조를 관찰하였고, d.c 전도도 측정을 통하여 다결정성 시료계들이 가지는 전도도의 온도 의존성으로부터 구한 활성화 에너지는 0.17 eV였다.다.

• 한국결정학회지
• /
• 제6권1호
• /
• pp.1-13
• /
• 1995

융액인상법에 의해 Cr:A12O3 및 Ti:A12O3 단결정을 육성한 후 인상속도, 회전속도, 주입이온 및 결정육성 분위기와 같은 결정육성요소가 결정의 품질에 미치는 영향을 조사하고, 육성된 결정의 레이저 효율과 분광학적 물성을 측정하였다. 직경 20mm, 길이 100-135mm 크기의 결정을 <001>방위로 육성하였다. Cr:A12O3의 주입농도 0.5w/o, 인상속도 2.0mm/hr, 회전속도 30rpm으로 할 때 질소기체에 의한 비활성 분위기하에서 양질의 Cr:A12O3 결정이 얻어졌다. Ti:A12O3 단결정은 TiO2를 0.25w/o 주입하고 인상속도 1.5mm/hr, 회전속도 30rpm으로 육성할 때, 수소기체에 의한 환원성 분위기하에서 양질의 결정이 얻어졌다. 원자가가 변화하지 않는 Cr3+이온은 원자가가 변화하는 Ti4+이온을 주입할 때보다 효과적으로 탈포되었으며, Fe3+이온은 Ti3+이온에 대해 탈포를 촉진하는 효과가 있었다. Ti:A12O3 단결정 육성시 90% N2 - 10% H2 혼합기체를 사용하여 환원성 분위기를 조성하는 것이 원자가 변화 및 탈포에 좋은 효과를 나타내었다. 흡수 및 형광방출 스펙트럼 조사 결과 Cr:A12O3 단결정에서 4A2 → 4F2 및 4F1 천이에 의한 흡수와 E→4A2(R1) 및 2A→4A2(R2) 천이에 의한 형광방출 천이를 확인하였다. R1 및 R2 천이의 레이저 주파장은 각각 696±5nm 및 692 ±5nm이고, 각 천이의 형광선폭은 12A, 형광수명은 152 μsec로 측정되었다. Ti:A12O3 단결정에서는 4T2→ 4E의 흡수천이와 4E→4T2의 천이에 의해 650nm-1050nm 범위에서 파장가변이 가능한 형광방출천이가 일어남을 확인하였으며 형광수명은 147μsec, figure of merit는 125.4로 측정되었다. Ti:A12O3 단결정으로부터 제조한 레이저봉을 이용하여 레이저 공진한 결과 레이저 발진효율은 9%로 측정되었다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2005년도 춘계학술발표대회 및 제8회 신소재 심포지엄 논문개요집
• /
• pp.107-107
• /
• 2005

• Corrosion Science and Technology
• /
• 제3권4호
• /
• pp.140-147
• /
• 2004

High temperature oxidation of Fe-19Cr and Fe-19Cr-0.2Ti alloys is studied at 1173-1373 K in 16.5 kPa $O_2$ - balances $N_2$ atmosphere aimed at clarifying the effect of titanium addition. Oxidation rate of Fe-19Cr alloy was accelerated with titanium. For both alloys chromium rich $(Fe,\;Cr)_2O_3$ was formed as a major oxidation product. On Fe-19Cr-0.2Ti alloy, a thin layer composed of spinel type oxide and titanium oxide was also formed and an internal oxidation of titanium was observed. Titanium was concentrated at the oxide surface and internal oxidation zone but a small amount of titanium was also found in the intermediate corundum type $(Fe,\;Cr)_2O_3$ layer. Crystals of corundum type $(Fe,\;Cr)_2O_3$ formed on Fe-19Cr alloy are coarse but that formed on Fe-19Cr -0.2Ti alloys were fine and columnar. Reason for the difference in oxidation kinetics and crystal structure will be discussed relating to the distribution of aliovalent titanium in corundum type $(Fe,\;Cr)_2O_3$ oxide layer.

• 한국재료학회지
• /
• 제22권12호
• /
• pp.682-688
• /
• 2012

In this study we aimed to examine the co-doping effects of 1/6 mol% $Co_3O_4$ and 1/4 mol% $Cr_2O_3$ (Co:Cr = 1:1) on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-$Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi = 0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Co,Cr-doped ZBS, ZBS(CoCr) varistors were controlled using the Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$), ${\alpha}$-spinel ($Zn_7Sb_2O_{12}$), and ${\delta}-Bi_2O_3$ were formed in all systems. Pyrochlore was decomposed and promoted densification at lower temperature on heating in Sb/Bi = 1.0 by Cr rather than Co. A more homogeneous microstructure was obtained in all systems affected by ${\alpha}$-spinel. In ZBS(CoCr), the varistor characteristics were improved (non-linear coefficient, ${\alpha}$ = 20~63), and seemed to form ${Zn_i}^{{\cdot}{\cdot}}$(0.20 eV) and ${V_o}^{\cdot}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to be composed of an electrically single barrier (0.94~1.1 eV) that is, however, somewhat sensitive to ambient oxygen with temperature. The phase development, densification, and microstructure were controlled by Cr rather than by Co but the electrical and grain boundary properties were controlled by Co rather than by Cr.

• 전기화학회지
• /
• 제18권1호
• /
• pp.17-23
• /
• 2015

$Li_4Ti_5O_{12}$는 우수한 안정성으로 자동차용 리튬 이온 이차전지의 음극 활물질로서 각광 받고 있다. 그러나 넓은 밴드갭에 기인한 절연체 특성으로 고율 충/방전을 가능하게 하기 위해서는 전자 전도도의 개선이 필수적이다. 본 연구에서는 Cr 도핑을 통해 $Li_4Ti_5O_{12}$의 전자 전도도 개선을 목표로 하였으며, wet-mixing법을 통한 물질 합성시 도판트인 Cr 프리커서의 용해도 차이에 의한 Cr-doped $Li_4Ti_5O_{12}$의 전기화학적 특성 변화를 고찰하고자 하였다. 시료의 물리적 특성은 ICP, XRD, SEM, EXAFS을 통하여 확인하였고 1.0V~3.0V (vs. $Li/Li^+$) 하에서 충/방전 특성을 조사하였다. 프리커서의 용해도는 합성된 물질의 상(phase) 및 모폴로지에 큰 영향을 미쳤으며, 가장 용해도가 높은 $Cr(NO_3)_2$ 프리커서로부터 합성된 경우 Bare $Li_4Ti_5O_{12}$와 비교하여 약 2배 개선된 고율 충/방전 특성(130 mAh/g @ 10 C)을 확인하였다.