• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.441-444
• /
• 2007

In this paper, the resonance characteristics of ZnO-based film bulk acoustic resonator (FBAR) devices with high-quality multi-layer reflectors are proposed. The ultrathin Cr film $(300\;\AA-thick)$ between $SiO_2$ film and W film is formed by a sputtering-deposition in order to enhance the adherence at their interfaces. The resonance frequency was observed to vary with the number of the reflectors. This seems to be attributed to the change in the effective thickness of the ZnO film. Also, increasing the number of layers has led to a significant improvement of the series/parallel quality factor.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.681-682
• /
• 2008

This paper propose skin color detection that uses MLP(Multi Layer Perceptron) and multiple color models. The proposed method reduces weight of MLP by partial connection between input layer and hidden layer based on color models, and the using color models are RGB model and YCbCr model. The experimental result for proposed method showed 94% classification rate of skin and non-skin pixels with 32% decrease in the number of weight compare to general MLP on the average.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.4
• /
• pp.361-364
• /
• 2008

Tips of probe card were fabricated using MEMS technology. P-type silicon wafer with $SiO_2$ layer was used as a substrate for fabricating the probe card. Ni-Cr and Au used as seed layer for electroplating Ni were deposited on the silicon wafer. Line patterns for probing devices were formed on silicon wafer by electroplating Ni through mold which formed by MEMS technology. Bridge structure was formed by wet-etching the silicon substrate. AZ-1512 photoresist was used for protection layer of back side and DNB-H100PL-40 photoresist was used for patterning of the front side. The mold with the thickness of $60{\mu}m$ was also formed using THB-120N photoresist and probe tip with thickness of $50{\mu}m$ was fabricated by electroplating process.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.1
• /
• pp.200-205
• /
• 1995

The 1st and 2nd-order grating structure for long wavelength DFB(Distributed FeedBack) laser diodes are successfully fabricated on InP substrates by using electron beam lithography and reactive ion etch techniques, and also characterized non-destructively by diffraction analysis without removal of photo-resis layer. A new composite layer made by lifted-off Cr layer on thin SiO2 film is developed and used as an etch mask, because PMMA, the e-beamresist, is unsuitable for reactive ion etch of InP. In addition, it is experimentally confiremed that diffraction analysis makes it possible to predict the grating parameters, and the analysis can be used as a non-destructive on-line test to prevent incomplete gratings from being successively processed.

• Journal of the Korean Society of Safety
• /
• v.32 no.2
• /
• pp.112-116
• /
• 2017

Present study investigated the influence of time step size, turbulent eddy viscosity, and the number of layer on rapid and unsteady propagation of dam break flow. When the time step size had a value such that it resulted in Cr of 0.89, a significant numerical oscillation was observed in the vicinity of the wave front. Higher turbulent viscosity ensured smooth and mild slope of velocity and water stage compared with the flow behavior by no viscosity. The vertical velocity at the lower layer positioned near the bottom showed lower velocity compared with other layers.

• Laser Solutions
• /
• v.2 no.2
• /
• pp.8-17
• /
• 1999

This study includes a basic feature of laser surface alloying for enhancing the surface properties of materials. Effects of laser processing parameters such as beam power, beam size, scanning speed on the shape and composition of alloyed layer was simulated in case of moving beam conditions (2-dimensional numerical methods). Simulated results were compared with experiments, in which the plasma coating of 80% Ni ＋ 20% Cr deposited on the SS41 substrate was remelted with CO2 laser with Gaussian energy distribution. Simulation and experiments revealed that the shape (dimension)and composition of laser alloyed layer were strongly dependent upon the process parameters, especially interaction time (travel speed) as compared to beam diameter, beam power and absorptivity. The shape and composition of alloyed layervaried more or less exponentially with parameters.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.294-297
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. Higher friction coefficient was obtained at harder coating with rougher surface. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with indentation hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics after nano scratching more than indentation hardness.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.4
• /
• pp.16-19
• /
• 2017

For the economical and environmental-friendly fabrication of polisher, Mo mask layer were sputtered on glass substrate instead of Cr mask material. Mo mask layers were sputtered by pulsed-DC sputtering and Photoresist patterns were formed on Mo mask layer for different develop times and optimized. After Mo mask layer were patterned and exposed glass was wet etched by HF solution for different etching times, the remaining Mo mask was stripped by using Al etchant. Develop time of 30 sec and HF wet etching time of 3 min were selected as optimized process condition and applied to the fabrication of polisher.

• Corrosion Science and Technology
• /
• v.12 no.1
• /
• pp.56-64
• /
• 2013

An Eectrolytic Corrosion(EC) test method was evaluated by the comparison with Copper Accelerated Acetic Salt Spray(CASS) and Neutral Salt Spray(SS) tests. Those methods were applied in order to evaluate corrosion resistance of Ni-Cr plated and Zn-plated Fe substrates. The correlations between results obtained by different test methods were investigated. Results showed that the electrochemical method such as the EC test method was superior to the conventional methods such as CASS and SS, in terms of the quantitative accuracy and the test-time span. Furthermore, the EC test method provided the useful means to estimate the initiation of corrosion of each layer by monitoring the rest potentials of the coated layers such as Ni, Cr, and Zn on Fe substrate. With regard to test time spans, the EC test provided the 78 times and 182 times faster results than the CASS test in cases of $Fe+5{\mu}m$ $Ni+0.5{\mu}m$ Cr and $Fe+20{\mu}m$ $Ni+0.5{\mu}m$ Cr respectively, while the EC test was 85 times faster results than the Salt Spray test in the case of $Fe+20g/m^2$ Zn. Therefore, the EC test can be the better method to evaluate the resistance to corrosion of coated layers than the conventional methods such as the SS test and the CASS.

• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.1
• /
• pp.31-39
• /
• 1999

In the present study, oxidation behavior of 304 and 316 stainless steels was investigated. After solution treatment, specimens were polished up to $1{\mu}m$ $Al_2O_3$ grade and then subjected to oxidation treatment in dry air. The range of temperature was used for oxidation treatment at $300^{\circ}C{\sim}500^{\circ}C$ and TEM was used for analyzing the components and structure of oxide film. Also, these results were compared with the results of ESCA and TG. According to the results of TEM analysis, it was found that Cr oxide film was formed on top of the surface after room temperature oxidation but amorphous Fe oxide was formed on top of the surface and polycrystalline $(Cr,Fe)_2O_3$ was formed below the amorphous Fe oxide layer after $500^{\circ}C$ oxidation treatment. The oxidized specimens at $500^{\circ}C$ showed that 316 stainless steel resists more strongly to grain and grain boundary oxidation than 304 stainless steel. These results suggested that Mo component resolved in 316 stainless steel matrix suppressed the formation of Cr carbide which may results in local Cr deplete area.