• 한국환경보건학회지
• /
• 제29권1호
• /
• pp.62-66
• /
• 2003

The biological denitrification batch tests were conducted to optimize the operating conditions with various temperature and initial SCO $D_{Cr}$ /N $O_3$-N ratio. and the denitrification rates were analyzed various SCO $D_{Cr}$ /N $o_3$-N ratio of influent with swine wastes fermented and temperature. The finishing time of denitrification was within 15 hours, 12 hours, and 6 hours as the temperature of denitrification applied were 15$\pm$1$^{\circ}C$, 25$\pm$1$^{\circ}C$, and 31$\pm$1$^{\circ}C$, respectively. From the batch tests, denitrification rate was operated with over 3 of SCO $D_{Cr}$ /N $O_3$-N ratio. Denitrification rate was increased as the temperature of denitrification, increased such as 2.40-3.90 mg N $O_3$-N/gMLVSSㆍhr, 6.10-7.60 mgN $O_3$-N/gMLVSSㆍhr, and 14.40-15.88 mgN $O_3$-N/gMLVSSㆍhr, respectively. The denitrification rate was increased as the ratio of initial SCO $D_{Cr}$ N $O_3$-N increased. However, it was found that the suitable ratio of SCO $D_{Cr}$ /N $O_3$-N for denitrification should be considered because the ratio of mg SCO $D_{Cr}$ , consumed per mg N $O_3$-N removed varied depend on the influent SCO $D_{Cr}$ /TKN ratios.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.1107-1113
• /
• 2002

This study presents the hydrogen emblittlement in the metal, which decreases the ductility and then induces the brittle fracture. The contribution deals with the effect of strain rate and notch geometry on hydrogen emblittlement of 1.25Cr-0.5Mo and 2.25Cr-1Mo steels, which are in use at high pressure vessel. Smooth and notched specimens were examined to obtain the elongation and tensile strength. For charging the hydrogen in the metal, the cathodic electrolytic method was used. In this process, current density is maintained constant. The amount of hydrogen penetrated in the specimen was detected by the hydrogen determenator(LECO RH404) with the various charging time. The distribution of hydrogen concentration penetrated in the specimen was obtained by finite element analysis. The amount of hydrogen is high in smooth specimen and tends to concentrate in the vicinity of surface. The elongation and tensile strength decreased with the passage of charging time in 1.25Cr-0.5Mo and 2.25Cr-1Mo steels. The elongation increased and tensile strength decreased as strain rate increased. As a result of this study, it is supposed that 1.25Cr-0.5Mo steel is more sensitive than 2.25Cr-lMo steel in hydrogen embrittlement. Hydrogen embrittlement susceptibility of notched specimen after hydrogen charging is more remarkable than that of smooth specimen.

• 한국안광학회지
• /
• 제3권1호
• /
• pp.223-228
• /
• 1998

$SiO_2-TiO_2-M_xO_y$ (M = Co, Cr or Cu)계의 비정질 박막을 현미경용 슬라이드 유리판 위에 전구체 용액을 스핀코팅방법으로 제조하였다. 전구체 용액은 tetraethyl orthosilicate, titanium trichloride, 그리고 코발트질산염, 크롬질산염, 구리질산염을 사용하여 합성하였다. X-선 회절분석 (${\theta}-2{\theta}$ scan)을 통하여 박막내에 $Co_3O_4$, $Cr_2O_3$, CuO 결정의 석출이 없는 비정질 박막임을 확인하였다. 코발트는 4면체배위의 $ Co^{2+}$로, 크롬은 4면체정배위의 $Cr^{6+}$로, 구리는 8면체배위의 $Cu^{2+}$로 존재하였다. 이 비정질박막의 표면에서 crack과 texture는 발견할 수 없었으며 파단면에서 박막악과 유리판 간의 계면은 균일한 조직을 보였다.

• 비파괴검사학회지
• /
• 제27권5호
• /
• pp.417-425
• /
• 2007

보자력 측정을 통하여 페라이트기 9Cr-1Mo-V-Nb 내열강의 크리프-피로변형 동안 미세조직의 변화를 평가하였다. 크리프-피로시험은 $550\;^{\circ}C$에서 각각 인장유지시간을 60초와 600초로 하여 수행 하였다. 보자력은 파단 전까지 감소하였고 경도는 파단 시까지 지속적으로 감소하였다. 크리프-피로 수명소비율이 증가함에 따라서 $M_{23}C_6$ 탄화물은 오스트왈드 성장기구를 따라서 조대화가 나타났지만 MX 탄질화물은 $550\;^{\circ}C$에서 안정하기 때문에 조대화가 나타나지 않았다. 마르텐사이트 래스 폭은 래스경계에서의 전위회복으로 인해 증가하였다. 보자력은 전위, 석출물 그리고 마르텐사이트 래스경계와 같은 미세조직적 특성에 영향을 받게 되며 이를 미세조직변화와 관련하여 이해하였다. 결과적으로, 본 연구는 페라이트기 9Cr-1Mo-V-Nb 내열강의 크리프-피로변형 동안 미세조직의 변화와 손상 정도를 보자력을 통하여 평가하는 것을 제안하였다.

• Journal of Microbiology and Biotechnology
• /
• 제10권5호
• /
• pp.580-586
• /
• 2000

A soluble Cr(VI) reductase was purified from the Cr(VI) reducing strain Escherichia coli ATCC33456 by ammonium sulfate fractionation, and chromatographies on Q-Sepharose FF, Cibacron blue 3GA dye affinity, Mono-Q 5/5, and Superdex 200 HR 10/30 columns. The estimated molecular mass of the purified enzyme was 27 kDa on SDS-polyacrylamide gel electrophoresis and 54 kDa on gel filtration, thus indicating a dimeric structure. The isoelectric point of the enzyme was pH 4.85. The optimum reaction pH and storage pH were both 7.0, the optimum reaction temperature was $37^{\circ}C$, and the storage temperature was $4^{\circ}C$. NADH and NADPH both served as electron donors for the reductase, with $V_{max}$ of 68.3 ${\mu}M$ Cr(VI)/min/mg protein and Km of 7.6 $\mu$M using HADH, and Vmax of 42.3 ${\mu}M$ Cr(VI)/min/mg protein and Km of 14.6 $\muM$ using NADPH. When 1 mM EDTA was added, the Cr(VI) reducing activity increased 4-fold.

• 상하수도학회지
• /
• 제29권1호
• /
• pp.33-38
• /
• 2015

In this study, flat-type photocatalytic reaction system is applied to reduce toxic hexavalent chromium (Cr(VI)) to trivalent chromium (Cr(III)) in aqueous solution under UV irradiation. To overcome the limitation of conventional photocatalysis, a novel approach toward photocatalytic system for reduction of hexavalent chromium including nanotubular $TiO_2$ (NTT) on two kinds of titanium substrates (foil and mesh) were established. In addition, modified Ti substrates were prepared by bending treatment to increase reaction efficiency of Cr(VI) in the flat-type photocatalytic reactor. For the fabrication of NTT on Ti substrates, Ti foil and mesh was anodized with mixed electrolytes ($NH_4F-H_2O-C_2H_6O_2$) and then annealed in ambient oxygen. The prepared NTT arrays were uniformly grown on two Ti substrates and surface property measurements were performed through SEM and XRD. Hydraulic retention time(HRT) and substrate type were significantly affected the Cr(VI) reduction. Hence, the photocatalytic Cr(VI) reduction was observed to be highest up to 95% at bended(modified) Ti mesh and lowest HRT. Especially, Ti mesh was more effective as NTT substrate in this research.

• 한국도로학회논문집
• /
• 제9권3호
• /
• pp.75-82
• /
• 2007

터널 내 축적된 다양한 오염원들은 간헐적으로 수행되는 세척과정 중에 폐수로 배출되게 되며, 서울 시내 3개 터널 지점에서 수행된 수질분석결과 SS, $COD_{Cr}$, T-N, $NH_3-N$, $NO_3-N$, Zn, Cu, Cr(+6). Mn, Mg, Phenol. $CN^-$, E-Coli 등이 고농도 형태로 배출되는 것으로 나타났다. 한편, 이러한 오염수질의 배출농도 특성은 터널 세척 폐수의 채취 방법, 세척횟수, 세척수량, 터널내벽 특성, 통행량, 배수 특성 등에 따라 다양한 농도범위를 보여주는 것으로 나타났다. 한편, 수집된 터널 세척폐수를 단순 중력침전을 이용하여 저감실험을 수행한 결과, $COD_{Cr}$는 80%, T-N, T-P는 각각 30, 90% 제거됨을 확인하였고, 중력침전 분리를 통하여 제거되지 않은 잔여 오염물질에 대하여 GAC 소재를 통한 흡착실험(터널 세척폐수 $1{\ell}$에 대하여 GAC를 50g을 투입) 결과, $COD_{Cr}$, T-N, Zn, Cu, Mn, Phenol, CN 항목에서 80% 이상 제거됨을 확인하였다.

• 동의생리병리학회지
• /
• 제26권1호
• /
• pp.26-34
• /
• 2012

This study is to investigate the effects of Chinemys reevesii (CR) on allergic inflammation mechanism related chronic dermatitis. To investigate the effects of CR, we study inhibitory effect of CR on the levels of pro-inflammatory cytokines released from RAW 264.7 cell stimulated with lipopolysaccaride (LPS), and EoL-1, THP-1, Jutkat cell stimulated with Dermatophagoides pteronyssinus (DP), and LPS induced acute inflammatory BALB/c mouse model. CR reduced the levels of IL-$1{\beta}$ released from RAW 264.7 cell stimulated with LPS at 20 ug/ml, 10 ug/ml concentration. CR significantly reduced the levels of MCP-1 released from EoL-1 cell, IL-6 from THP-1 cell, and IL-4, IL-5, TNF-${\alpha}$ from Jutkat cell stimulated with DP at all the concentration. CR significantly reduced the levels of TNF-${\alpha}$, IL-6, IL-$1{\beta}$, in LPS induced inflammatory BALB/c mouse model, in a dose-dependent manner. These results suggested that CR has suppressive effects on pro-inflammatory cytokines in various inflammation related cell lines through the regulation of immune system. CR could be a therapeutic agent for treatment of chronic inflammatory dermatitis in the future.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.373-383
• /
• 2021

The effect of Cr addition to high Mn steel on flow-accelerated corrosion (FAC) behavior in a neutral aqueous environment was evaluated. For comparison, two types of conventional ferritic steels (API X70 steel and 9% Ni steel) were used. A range of experiments (electrochemical polarization and impedance tests, weight loss measurement, and metallographic observation of corrosion scale) were conducted. This study showed that high Mn steel with 3% Cr exhibited the highest resistance to FAC presumably due to the formation of a bi-layer scale structure composed of an inner Cr enriched Fe oxide and an outer Mn substituted partially with Fe oxide on the surface. Although the high Mn steels had the lowest corrosion resistance at the initial corrosion stage due to rapid dissolution kinetics of Mn elements on their surface, the kinetics of inner scale (i.e. Cr enriched Fe oxide) formation on Cr-bearing high Mn steel was faster in dynamic flowing condition compared to stagnant condition. On the other hand, the corrosion scales formed on API X70 and 9% Ni steels did not provide sufficient anti-corrosion function during the prolonged exposure to dynamic flowing conditions.

• 한국대기환경학회지
• /
• 제25권3호
• /
• pp.179-187
• /
• 2009

This paper describes the field evaluation of a sampling and analytical method for the quantity of airborne hexavalent chromium ($Cr^{6+}$) in the industrial areas, such as Sihwa and Banwol. Ambient measurements were performed by using the cellulose filter during the four seasons (October 2006 to June 2007). The determination of hexavalent chromium was carried out by ion chromatography. Performance validations, including method detection limit, relative standard deviation, and recovery percent, were also investigated. The mean concentrations of $Cr^{6+}$ in Sihwa and Banwol were 0.767 and 0.796 $ng/m^3$, respectively, which are similar to those of other foreign industrial areas. The seasonal variations of $Cr^{6+}$ levels were not quite different, which implies that the chromium was continuously emitted from the industrial sources throughout the year. The concentration variations between total chromium and $Cr^{6+}$ have also shown the similar pattern, suggesting that these components originate from the same sources. The concentration of $Cr^{6+}$ was found to be 0.7 to 2.4% of the total chromium. From these results, the approach using the cellulose filter may be suitable to collect $Cr^{6+}$ in the ambient air.