• Journal of Surface Science and Engineering
• /
• v.52 no.6
• /
• pp.293-297
• /
• 2019

Quasi-nano-hardness and corrosion behaviors of neutron-irradiated reactor pressure vessel (RPV) steels such as 15Ch2MFA (Ni<0.4, 2.520 n/㎠ (En>1.0 MeV) for 32 days. Quasi-nano-hardnesses of the 15Ch2MFA and 15Cr2NHFA steels were 183.8 and 179.8 Hv, respectively. Their corrosion rates and corrosion potentials were 2.4×10^-4Acm^-2, -515.9 mV_SHE and 6.8×10^-4 Acm^-2, -523.6 mV_SHE in NACE standard TM0284-96 solution at room temperature, respectively. 15Ch2MFA steel showed better quasi-nano-hardness and corrosion resistance than 15Cr2NHFA steel in this test condition.

• Journal of Korea Foundry Society
• /
• v.19 no.6
• /
• pp.472-483
• /
• 1999

The effects of rapid solidification and Cr addition to the microstructure variations of the rapid solidified Ti-48Al-xCr(X = 2,4,6) alloys have been investigated using X-ray diffractometry, optical microscopy, scanning electron microscopy and transmission electron microscopy. The segregated coarse ${\gamma}$ phase was eliminated and the microstructure was refined by rapid solidification of the cooling rate of $10^4-10^6\;^{\circ}C/sec$. The lattice parameters and tetragonality of ${\gamma}$ phase decrease with the increase Cr content and by the rapid solidification. Non-equilibrium phase ${\alpha}$ remains at room temperature condition, which would be resulted from the restriction of phase transformation ${\alpha}$ to ${\alpha}_2+{\gamma}$.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.10
• /
• pp.1049-1051
• /
• 2000

A chromia-pillared clay has been prepared by ion exchange type intercalation reaction between the sodium ion in montmorillonite and the trimeric chromium oxyformate (TCF) ion, and by subsequent heat-treatment. The structural and thermal properties have been systematically studied by thermal analysis, powder XRD, IR spec-troscopy, and XAS. The gallery height of~6.8 $\AA$ upon intercalation of the TCF ion suggests that the $Cr_3O$ plane is parallel to the aluminosilicate layers. Even though the basal spacing of TCF intercalated clay decreases slightly upon heating, the layer structure was retained up to $550^{\circ}C$ as confirmed by XRD and TG/DTA. Ac-cording to the EXAFS spectroscopic analysis, it is identified that the (Cr-Cr) distance of 3.28 $\AA$ between vertex-linked CrO6 octahedra in TCF splits into 2.64 $\AA$, 2.98 $\AA$, and 3.77 $\AA$ due to the face-, edge-, and corner-shared CrO6 octahedra after heating at $400^{\circ}C$, implying that a nano-sized chromium oxide phase was stabilized within the interlayer space of clay.

• Korean Journal of Materials Research
• /
• v.22 no.1
• /
• pp.46-53
• /
• 2012

In this study, mechanical tests and microstructural analyses including TEM analyses with EDX of precipitates in modified 9Cr-1Mo steel were carried out to determine the cause of embrittlement observed after heat-treatment, which limits the usage of the alloy for power plants. Mod. 9Cr-1Mo steel specimens at austenite temperature were quenched to the molten salt baths at $760^{\circ}C$ and $700^{\circ}C$, in which the specimens were kept for 10 min ~ 10 hr with subsequent air-cooling. Impact tests showed that the impact value dropped abruptly when the specimens were kept longer than 30 min at $\sim760^{\circ}C$ reaching to minima in about 1 hr, and then increasing at further retention. The tensile strength of the specimens reached the minimum value without much change afterward, whereas the values of elongation showed the same trend as that of the impact value. The isothermally heat-treated steel at $700^{\circ}C$ also showed a minimum impact value in about 1 hr. These results suggest that the isothermal heattreatment at 760 and $700^{\circ}C$ for about 1 hr induces temporal embrittlement in Mod. 9Cr-1Mo steel. The microstructural examination of all the specimens with extraction replica of the carbides revealed that the specimens with temporal embrittlement had $Cr_2C$, indicating that the cause of the embrittlement was the precipitation of the $Cr_2C$. In addition, TEM/EDX results showed that the Fe/Cr ratio was 0.033 to 0.055 for $Cr_2C$, whereas it was 0.48 to 0.75 for $Cr_{23}C_6$, making the distinction of the $Cr_2C$ and $Cr_{23}C_6$ possible even without direct electron diffraction analyses.

• Journal of the Korean Magnetics Society
• /
• v.10 no.2
• /
• pp.74-80
• /
• 2000

CoCr$_{x}$ Fe$_{2-x}$O$_4$(0.0$\leq$x$\leq$1.0) ferrites have been fabricated by sol-gel method. The crystallographic and magnetic properties of the samples were investigated by means of x-ray diffraction, scanning electron microscophy, Mossbauer spectroscopy and vibrating sample magnetometry. The structure of all the samples is cubic spinel type and the lattice constant decrease with increasing Cr content. The substituted Cr ions were located only in the B-site. The particle size also decreases with increasing Cr content. The Mossbauer spectra consist of two sextets due to Fe$^{3+}$ions at A- and B sites for 0.0$\leq$x$\leq$0.6, while, a paramagnetic doublet appears for 0.8$\leq$x$\leq$1.0. The magnetic hyperfine field decreases with increasing Cr content. The relaxation spectra was shown at 0.8$\leq$x$\leq$1.0 in CoCr$_{x}$ Fe$_{2-x}$O$_4$. The coercivity decreases drastically, while, the saturation magnetization decreases linearly with increasing x.ing x.

• The Korean Journal of Nuclear Medicine
• /
• v.19 no.1
• /
• pp.127-136
• /
• 1985

To evaluate change of serum $beta_2-microglobulin$ concentration$(s\beta_2-MG)$ and the usefulness of $s\beta_2-MG$ and $s\beta_2-MG/serum$ creatinine concentration(sCr) ratio in various renal diseases, $s\beta_2-MG$ and sCr were measured in 25 normal controls and 90 patients of various renal diseases(16 cases of glomerulonephritis, 12 cases of acute renal failure, 8 cases of chronic renal failure, 24 cases of nephrotic syndrome, 15 cases of tubulointerstitial diseases and 15 cases of lupus nephritis) using $Phadebas^\circledR$ $Beta_2-Micro$ Test kits. The results were as follows; 1) In normal control, the mean value of $s\beta_2-MG$ was $1.65{\pm}0.41mg/l$ and the mean value of $s\beta_2-MG/sCr$ ratio was $0.14{\pm}0.05$. 2) In various renal diseases, the mean value of $s\beta_2-MG$ was $6.74{\pm}5.47mg/l$. The mean value of $s\beta_2-MG/sCr$ ratio was $0.24{\pm}0.11$ and significantly elevated than that of normal control. (p<0.05) 3) The correlation between $s\beta_2-MG$ and sCr in glomerular and tubulointerstitial disease was log $s\beta_2-MG-0.90$ log sCr-0.48 and its correlation coefficient was 0.78(p<0.05). 4) In glomerular disease, the correlation between $s\beta_2-MG$ and sCr was log $s\beta_2-MG-0.89$ log sCr-0.46(r - 0.76) and in tubulointerstitial disease, it was log, $s\beta2-MG-0.95$ log sCr-0.59 (r-0.87). There was no significant difference between the two groups(p<0.05). 5) Among 32 cases of glomerular and tubulointerstitial disease patients, whose sCr was within normal range, 17 cases showed elevated $s\beta_2-MG$. The mean values of $s\beta_2-MG/sCr$ ratio in these patients was $0.30{\pm}0.14$ and significantly elevated than that of normal control(p<0.05). 6) In 15 cases of lupus nephritis, 12 cases showed elevated $s\beta_2-MG$ with normal sCr and 12 cases showed elevated $s\beta_2-MG/sCr$ ratio. With above results, it was found that the $s\beta_2MG$ can be used as an index of glomerular filtration rate as in the case of sCr and that $s\beta_2-MG/sCr$ ratio can be used as a tool in early detection of slightly decreased glomerular filtration rate and in detection of the renal disease of increased $\beta_2-MG$ production.

• KSBB Journal
• /
• v.15 no.1
• /
• pp.49-54
• /
• 2000

Bioluminescence of Photobacterium phosphoreum has been used for the detection of pollutants in the environment. Immobilization method was used to maintain the stability of bioluminescence of P. phosphoreum. The carboxymethylcellulose was investigated to find out whether it was suitable for the immobilization of P. phosphoreum as a matrix without disturbing the bioluminescence emission. A maintenance of bioluminescence was determined from the P. phosphoreum immobilized on the various concentrations of carboxymethylcellulose. A relatively high bioluminescence intensity was shown with immobilized cells on 1%(w/v) carboxymethylcellulose. The effect of carboxymethylcellulose concentrations on the sensitivity of Crcompounds including $Na_{2}CrO_{4}$, $K_{2}CrO_{4}$, $CrO_{3}$, CrK$(SO_4)_{2}$ and $CrCl_{3}$ to the bioluminescence intensity. The calculated $EC_{50}$ showed that the linear relations between such substances and bioluminesence intensity were established.

• Journal of Advanced Navigation Technology
• /
• v.28 no.4
• /
• pp.532-537
• /
• 2024

In this study, wear characteristics and microstructure changes due to changes in alloy composition of Ni-Cr-Mo-V and Ni-Cr-Mo low-alloy steels used in brake discs for transportation system such as aircraft and high-speed trains. As a result of the hardness test, the hardness of C-Mo-V steel was the highest at 39.4±0.9HRc, and the hardness of Ni-Cr-Mo steel was the lowest at 32.4±0.6HRc. The friction coefficient tended to decrease as the vertical load increased. At a vertical load of 1 N, the friction coefficient of Ni-Cr-Mo steel was the highest at 0.842, and at a vertical load of 5 N, Mn-Cr-V steel was the highest at 0.696. Ni-Cr-Mo showed the largest wear scar width, depth, and wear amount, with a width of 711 ㎛, a depth of 8.24 ㎛, and a wear amount of 11 mg under a vertical load of 1 N, and a width of 1,017 ㎛, a depth of 19.17 ㎛, and a wear amount of 17 mg under a vertical load of 5 N. As a result of wear mechanism analysis, ploughing, delamination, and adhesion in all specimens, with plastic deformation being more prominently observed in Ni-Cr-Mo.

• Journal of Embryo Transfer
• /
• v.10 no.1
• /
• pp.53-63
• /
• 1995

The effects of different protein sources (serum vs bovine serum albumin), growth factors (EGF and PDGF) and co-culture with various type of somatic cel1s (BOEC, MEF and BRL) on the in vitro development of in vitro matured / in vitro fertilized bovine oocytes were examined, and the viability of frozen/thawed embryos derived from IVM /IVF was examined. Cell numbers of blastocysts were also counted. In Experiment 1, CR$_1$aa with serum was superior to CR$_1$aa with BSA in producing morulae plus blastocysts from IVM /IVF oocytes(24.4% vs 30.4%, p>0.05). In Experiment 2, more morulae plus blastocysts(42.3%) were produced in CR$_1$aa containing long /ml EGF than in the control CR$_1$aa(33.3%). In Experiment 3, 2- to 8-cell embryos derived from IVM /IVF oocytes were randomly allotted to one of 4 culture groups : a) CR$_1$aa ; b) CR$_1$aa + ing /ml PDGF ; CR$_1$aa + Sng /ml PDGF ; CR$_1$aa + lOng /ml PDGF ; culture resulted in 21.3, 51.2, 41.4 and 45.9%(p<0.05), respectively, developing into morulae and blastocysts. In Experiment 4, 0 and Sng /ml PDGF added to CR$_1$aa coculture with BRL or BOEC yielded 47.5, 42.5, 33.8 and 41.6% morulae and blastocysts, respectively. In Experiment 5, the proportion of embryos into morulae and blastocysts was highest in CR$_1$aa with MEF coculture group(50.9%) compared to any other group(CR$_1$aa, 22.3%; CR$_1$aa+BRL, 32.9%; CR$_1$aa+BOEC, 33.8%, p>0.05). In Experiment 6, survival rate of blastocysts produced by in vitro fertilization when cryoprotectant was removed in 0.7M glycerol+0.7M sucrose and 0.7M sucrose solution for 10 min. after thawing at 2$0^{\circ}C$ (Exp. H, 58.8%) was slightly higher than when cryoprotectant was removed 10%, 6.7% and 3.3% glycerol for 10 min. after thawing at 37$^{\circ}C$ (Exp. I, 54.3%). These study indicate that growth factors and somatic cell co-culture can increase the proportion of embryos that develop into morulae and blastocysts without an increase in the cell number and frozen /thawed method employed this experiment was not different.

• Journal of Sensor Science and Technology
• /
• v.6 no.3
• /
• pp.221-227
• /
• 1997

The Pd/NiCr gate MISFET-type sensors were fabricated for detecting hydrogen dissolved in high-capacivity transformer oil. To improve stability and high concentration sensitivity of the sensor, Pd/NiCr double catalysis metal gate was used. To reduce the serious gate voltage drift of the sensor induced by hydrogen, the gate insulators of 2 FETs were constructed with double layer of silicon dioxide and silicon nitride. The hydrogen sensitivity of the Pd/NiCr gate MISFET is about a half of Pd/Pt gate MISFET's sensitivity but the Pd/NiCr gate MISFET has good stability and high concentration detectivity up to 1000 ppm.