• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.1
• /
• pp.29-35
• /
• 2015

In this study, a FEM analysis is undertaken of a rubber sleeve which is mounted onto a spreading mandrel so as to avoid marking the first wrappings of coils (known as the 'end-mark'), as occasionally occurs when a concentrated load is placed on the edge of a steel sheet, significantly reducing its quality. A commercial numerical package, ANSYS, was utilized to analyze the structural behavior of the rubber sleeve. In general, the strain of the sleeve increases as the thickness of the rubber layer (H) covering the tubes increases, thus also increasing the surface of the sleeve for a constant boundary condition, and decreasing the pitch (P) between each tube, resulting in an increase in the strain on the surface of the sleeve for all rubber thickness conditions tested here. In a comparison of two different materials, rubber and urethane, when H=3 mm and P=1.1D, the maximum total deformations in these cases are 0.12669 mm and 0.086623 mm, respectively.

• Korean Journal of Agricultural Science
• /
• v.45 no.4
• /
• pp.623-634
• /
• 2018

This experiment was conducted to determine the effects of the pre- and post-harvest variable factors on the processed product of kimchi cabbage. Two kimchi cabbage cultivars, namely 'Chungwang' and 'Dongpung,' were grown in a field and under a plastic greenhouse condition and stored at $5^{\circ}C$ after harvesting with and without low-density polyethylene (LDPE) film packaging. Growths were determined after harvesting while salting characteristics were determined after the processing and storage. The results show that the height, weight and leaf thickness were higher in kimchi cabbages grown in the greenhouse than those grown in the field. The plastic house culture increased the kimchi cabbage growth of the head weight, head height and leaf thickness compared with that of the open field culture. However, the osmolality and firmness were higher in the outdoor cultivated kimchi cabbages. Kimchi cabbage packed in film covered sacks and stored at $5^{\circ}C$ showed lower weight loss than unpacked cabbages during storage. Salt concentration and pH were also affected by the different pre- and post-harvest factors after salting the kimchi cabbages. Salt concentrations of the kimchi cabbage were influenced by various factors such as the cultivars, cultivation methods and storage covering. Though the present findings showed a limited difference in salt concentration and pH between the cultivars of kimchi cabbages, this study suggests that there is a relationship between processed agricultural products and their pre- and post-harvest methods.

• Archives of Craniofacial Surgery
• /
• v.22 no.6
• /
• pp.337-340
• /
• 2021

Full-thickness nasal tip reconstruction is a challenging process that requires provision of ample skin and soft tissue, and intricate cartilage structure that maintains its architecture in the long term. In this report, we describe reconstruction of a full-thickness nasal tip and ala defect using a posterior auricular artery perforator based chondrocutaneous free flap. The flap consisted of two lay ers of skin covering conchal cartilage, and was based on a perforating branch of the posterior auricular artery. A superficial vein was secured at the posterior margin. The donor perforator was anastomosed to a perforating branch of the lateral nasal artery. The superficial vein was connected to a superficial vein of the surrounding soft tissue. The donor healed well after primary closure. The flap survived without complications, and the contour of the nasal rim was sustained at follow-up 6 months later. As opposed to combined composite reconstructions using a free cartilage graft together with a small free flap or pedicled nasolabial flap, the posterior auricular artery perforator free flap encompasses all required tissue types, and is similar in contour to the alar area. This flap is a useful option in single-stage reconstruction of nasal composite defects.

• Composites Research
• /
• v.18 no.4
• /
• pp.66-74
• /
• 2005

This paper reports new repair and strengthening mathod using improved material. This mathod have two type according to covering thickness of reinforcement. One type is near surface mounted FRP rod. Anther type is overay. Fiber Reinforced Plastic (FRP) materials has become very popular in recent years. FRP material used to rehabilitate many types of structures with superior characteristics such as high strength and stiffness and corrosion resistance. This strengthening mathod were used FRP rod which have better bond and shear strangth than current FRP rod. Development of FRP rod due to 3-D winding system. In addition, Ductile hybrid FRP has a certain plastic deformation and an elongation greater than 3% at maximum load is usually required for steel reinforcement in concrete structures. Moerover this mathod can be effective repair of base concrete by sprayed polymer mortar.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.161-166
• /
• 2001

The prototype of a tactile sensor with $4\times 4$ taxels using PVDF was fabricated. The electrode patterns of the thin Cu tape are attached to the 28${\mu}{\textrm}{m}$ thickness PVDF using conductive adhesive and covering the sensor using polyester film for insulation. The structure of the sensor is flexible and the fabrication procedure is easy relatively. Also the output characteristics of the sensor was nearly linear with 8% deviation. The signals of a contact pressure to the tactile sensor are sensed and processed through A/D converter, DSP system and personal computer. The reasonable performance for the detection of contact shape and force distribution was verified through the experiment.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.235-240
• /
• 2016

In this paper, a low-profile planar inverted-F antenna (PIFA) for ultrawideband (UWB) applications is proposed. The antenna consists of a PIFA and a ground plane with a slot. The addition of the slot not only improves the impedance matching of the PIFA but also forms an additional resonance. Therefore, the proposed antenna has a wideband characteristic covering the full UWB frequency range (3.1 GHz to 10.6 GHz) and a stable and nearly omnidirectional radiation pattern. The antenna also has a smaller volume and thickness compared to previous UWB PIFAs.

• Journal of information and communication convergence engineering
• /
• v.14 no.2
• /
• pp.65-70
• /
• 2016

This paper proposes and experimentally tests a modified circular slot antenna fed by a fork-like tuning stub for ultra-wideband (UWB) operation. The proposed antenna consists of a modified circular slot model and fork-like tuning stub. The proposed antenna is printed on a 34.0 mm × 30.0 mm FR4 substrate with thickness of 1.0 mm and relative permittivity of 4.4. The effect of various parameters of the circular slot and fork-like tuning stub is investigated for UWB operation. The modified circular slot and fork-like tuning stub are fabricated on the substrate to achieve wideband operation and good impedance matching. Experimental results demonstrated that the measured return loss exhibits an acceptable agreement with the simulated return loss and satisfies the -10 dB impedance bandwidth requirement while simultaneously covering the UWB bands. In addition, the proposed antenna shows good radiation characteristics and gains in the UWB bands.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.545-548
• /
• 2004

In Japan for protecting the slides of steep sloped areas covering the face of slopes by sprayed mortar became popular since 1970s. But, these mortar walls are getting older now. In this background, this study aims to find ways to develop a diagnostic technique of these faces of slope without physically contacting or destroying them. In doing so, we have used heat infrared imaging processing method and developed a simulation model to predict the weak portion of the wall. The results revealed that, by following the model vacuum of mortar wall can be detected having thickness up to 15cm.

• Journal of information and communication convergence engineering
• /
• v.13 no.3
• /
• pp.159-166
• /
• 2015

In this paper, a novel design for a triple-band coplanar waveguide (CPW)-fed monopole antenna for WLAN/WiMAX operations is proposed. The proposed antenna is printed on an FR4 substrate with an area of 22.0 mm × 30.0 mm, a thickness of 1.0 mm, and a relative permittivity of 4.4. The effects of various parameters of the proposed for triple band operation is investigated. Two half circular rings and a microstrip feed line are fabricated on the substrate to achieve triple band operation and good impedance matching. Prototypes of the proposed antenna have been fabricated and tested. Experiment results reveal that the measured return loss exhibits an acceptable agreement with the simulated return loss and satisfies the impedance bandwidth requirement of -10 dB, while simultaneously covering the WLAN and WiMAX bands. In addition, the proposed antenna shows good radiation characteristics and gains in the three operating bands.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.131-136
• /
• 2004

Impact sounds, such as those created by footsteps, the dropping of an object or the moving of furniture, can be a source of great annoyance in residential buildings. The character and level of impact noise generated depends on the object striking the floor, on the basic structure of the floor, and on the floor covering. This study base on the evaluate of isolation performance of impact sound according to the impact noise reduction methods. Reduction methods consist of four ways. First way is increase thickness of bare floor and other ways are using the soft coverings on the floor and ceiling assembles. Last way is make floating floor with shock absorbing materials.