• Journal of Biosystems Engineering
• /
• 제9권2호
• /
• pp.65-73
• /
• 1984

While most of researches on the performance of high temperature grain dryer have dealt mainly with improving dryer capacity and drying speed during the last twenty years, energy efficiency, in fact, has not been emphasized. Current fuel supplies and energy cost have shifted the emphasis to reducing the energy consumption for grain drying while maintaining dryer capacity and grain quality. Since the energy input for drying is relatively large, the recovery and reuse of at least part of the exhaust energy can significantly reduce the total energy consumption in existing drying systems. Unilization of exhaust heat in grain dryer either through direct recycling or by a thermal coupling in heat exchanger have been subject of a number of investigators. However, very seldom research in Korea has been done in this area. Three drying tests(non-recycling, 0.22 recycle ratio, and 0.76 recycle ratio)were performed to investigate the thermal efficiency and heat loss factors of continuous flow type dryer, and to analyze the effect of recycle ratio (weight of exhaust air recycled/total weight of input air) on the energy requriements for rough rice drying. The test results showed that when the exhaust air was not recycled, the energy lost from furnace was 15.3 percent of input fuel energy, and latent and sensible heat of exhaust air were 61.4 percent and 11.2 percent respectively. The heat which was required in raising grain temperature and stored in dryer was relatively small. As the recycle ratio of exhaust air was increased, the drying rate was suddenly decreased, and thermal efficiency of the kerosene burner was also decreased. Drying test with 0.76 recycle ratio resulted in 12.4% increase in fuel consumption, and 38.4% increase in electric power consumption as compared to the non-recycled drying test. Drying test of 0.22 recycle ratio resulted in 6.8% saving in total energy consumption, 8.0% reduction in fuel consumption, and 2.5% increase in electric power consumption as compared to the non-recycled drying test.

• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1317-1325
• /
• 2018

A generator-grid coupling calculation model is established to study the leading-phase operational capability of a 770 MW jumbo hydro-generator in a Chinese ultra-mega hydropower station. The static and dynamic stability of the generator are analyzed and calculated to obtain stability limits under leading-phase operating conditions. Three-dimensional (3D) time-varying nonlinear moving electromagnetic and temperature field models of the generator end-region are also established and used to determine the magnetic field, loss, and temperature of the end-region under the leading-phase operating condition. The simulation results agree with data measured from the actual 770 MW hydro-generator. This paper provides reliable reference data for the leading-phase operation of a jumbo hydro-generator, which will help to improve in the design and manufacture of future hydro-generators.

• 한국정보통신학회논문지
• /
• 제6권1호
• /
• pp.89-98
• /
• 2002

본 연구에서는 광계측 기술을 이용하여 배전자동화 개폐기 내에서 발생하는 전자 계측장치의 절연문제 및 측정오차의 문제점을 개선하기 위하여 배선자동화개폐기 내장형 광전류 및 광전압센서를 연구하였다. 자기광학 효과(magneto optic effect)인 페러데이효과(Faraday effect)를 이용하여 최적의 광전류 센서를 설계 제작하여 높은 전류까지 선형성을 유지시키고 다른 상의 전류에 대한 유도현상을 최소로 하기 위해 순철 코아를 사용하여 광전류 센서를 일체화시켜 설계 제작하였다. 설계내에서 결정의 굴절률 및 방위각의 변화에 의해 생기는 전기광학효과(electrooptic effect)인 포켈스 효과(pockels effect)를 이용하여 광전압센서를 구성하였으며 배전 자동화용 개폐기의 협소한 내부구조를 고려하여 공간전계방식을 채택하였다. 또한 다심의 광섬유를 개폐기와 외부의 신호처리 단말기와 연결하기 위하여 기밀형 멀티 광커넥터를 설계 자작하여 접속 손실 및 가스 누설 시험을 하였다. 전기적 특성시험에서 광 전류센서에서는 인가 전류에 대한 선형 특성은 20A 에서 700A까지 변동 오차 2.5% 이내의 선형성을 유지하였으며, 광전압센서에 있어서 인가 전압에 대한 선형 특성은 6.6kV에서 19.8kV까지 거의 변동 오차가 1% 이내로 우수한 선형 특성을 나타냈다.

• 한국전기전자재료학회논문지
• /
• 제17권11호
• /
• pp.1174-1177
• /
• 2004

The dielectric and piezoelectric properties of silver added 0.96 Pb(Z $r_{0.52}$ $Ti_{0.48}$) $O_3$-0.04 Pb(Mn,W,Sb,Nb)$_3$ ceramics were examined. By varying the contents of silver(0.0, 0.4, 1.0 mol%), the effect of silver addition on PZT-PMWSN ceramics was investigated at various sintering temperature(900, 1000, 1100 $^{\circ}C$). As increasing silver contents, the relative dielectric constant was increased and sinterability was enhanced. At the specimen with 0.4 mol% Ag and sintered at 1000 $^{\circ}C$, electromechanical coupling factor( $k_{p}$), mechanical quality factor( $Q_{m}$), dielectric constant($\varepsilon$$_{r}$) and dielectric loss were 0.502, 811, 991, 0.006, respectively. The results showed that the PZT-PMWSN/Ag composites have enhanced piezoelectic and dielectric properties and sintering temperature was lowered.red.

• Applied Science and Convergence Technology
• /
• 제26권4호
• /
• pp.70-73
• /
• 2017

The dielectric constant and loss of poling/non-poling was measured in the $Pb_{1-3x/2}La_x[(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ samples. The addition of $La^{3+}$ to the $Pb_{1-3x/2}La_x[(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ did not cause a large change in grain size. But the addition of $La^{3+}$ did show transition temperature, which shifted toward low temperature in the $Pb[(Mg_{1/3}Ta_{2/3})Zr]O_3$ systems. In addition, the dielectric and pyroelectric properties (${\varepsilon}{\sim}20000$, $p{\sim}0.03C/m^2K$) of this system using $La^{3+}$ have been greatly improved. Pyroelectrics $Pb_{0.97}La_{0.02}(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ system was found to have a relatively high ferroelectric FOMs ($F_V{\sim}0.035m^2/C$, $F_D{\sim}0.52{\times}10^{-4}Pa^{-1/2}$) at room temperature. Spontaneous polarization showed a value of $0.27{\sim}0.35C/m^2$ in the composition added to $La^{3+}$. The piezoelectric constant ($d_{33}=350{\sim}490pC/N$) and electromechanical coupling factor ($k_P=0.25{\sim}0.35$) are obtained in $Pb_{1-3x/2}La_x[(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ compositions with $La^{3+}$ dopant.

• 한국자기학회지
• /
• 제16권5호
• /
• pp.234-239
• /
• 2006

교환 결합력을 갖는 CoFe/MnIr 박막 시료에서 100 MHz$\sim$9 GHz의 주파수 범위에서 마이크로파 투자율을 측정하였으며, 이들 결과는 Landau-Lifshitz-Gilbert 이론을 사용하여 분석 하였다. 초기투자율 및 강자성 공명주파수는 CoFe의 두께 및 일방이방성에너지(unidirectional anisotropy)에 따라서 조절이 가능하며, 특히 공명주파수는 최대 20 GHz까지 조율이 가능하다. 따라서 마이크로파 대역에서 고투자율 및 저손실 특성을 갖는 CoFe/MnIr 재료는 수 GHz 대역에서 작동하는 마이크로파 부품에 적용 가능하다.

• Journal of Magnetics
• /
• 제21권4호
• /
• pp.509-515
• /
• 2016

We report on development of a ground-based bi-axial Search-Coil Magnetometer (SCM) designed to measure time-varying magnetic fields associated with magnetosphere-ionosphere coupling processes. The instrument provides two-axis magnetic field wave vector data in the Ultra Low Frequency or ULF (1 mHz to 5 Hz) range. ULF waves are well known to play an important role in energy transport and loss in geospace. The SCM will primarily be used to observe generation and propagation of the subclass of ULF waves. The analog signals produced by the search-coil magnetic sensors are amplified and filtered over a specified frequency range via electronics. Data acquisition system digitizes data at 10 samples/s rate with 16-bit resolution. Test results show that the resolution of the magnetometer reaches $0.1pT/{\sqrt{Hz}}$ at 1 Hz, and demonstrate its satisfactory performance, detecting geomagnetic pulsations. This instrument is scheduled to be installed at the Korean Antarctic station, Jang Bogo, in the austral summer 2016-2017.

• 한국가스학회지
• /
• 제25권6호
• /
• pp.14-21
• /
• 2021

-162℃ 초저온 상태의 LNG를 저장하는 저장탱크의 내조는 균열과 같은 결함에 대한 구조 건전성 평가가 필요하다. 전통적인 파괴역학 관점에서는 응력확대계수 K, J-적분 그리고 CTOD를 이용한 단일 매개변수 평가가 주로 수행되어왔다. 그러나 실제 구조에서 발생되는 균열선단은 구조물의 크기, 시편형상 그리고 인장과 굽힘과 같은 하중의 형태에 따라 구속효과의 차이로 인한 영향이 발생하게 된다. 단일 매개변수 파괴역학을 보완하기 위해 다양한 시도가 있었고, 대표적으로 Q-응력법이 있다. 본 논문에서는 비선형 탄성영역의 균열선단 응력장 평가에 적합한 J적분에 Q응력을 유도하여 2 매개변수 접근법을 사용하고자 한다. SENB 시편의 균열비 0.1~0.7 그리고 광폭시편 균열비 0.2~0.6에 시편 균열선단의 응력을 J-Q 평가법을 이용하여 구속효과를 정량적으로 평가 하였다.

• 한국인터넷방송통신학회논문지
• /
• 제22권2호
• /
• pp.35-42
• /
• 2022

본 논문에서는 SSPA(Solid state amplifier) 의 핵심 모듈인 결합기의 효율 및 격리 특성을 높이는 방법에 대해 연구하였다. 구체적으로 도파관 결합기에서 공용 포트와 격리 포트 정합을 이루어 격리도를 확보 하였다. 정합을 위한 매칭 구조는 원형 디스크 형태로 도파관 결합기 내부에서 음각으로 가공하게 된다. 구조는 매우 단순하여 안정적인 성능 확보가 가능하다. 그리고 이러한 구조는 이전 연구 대비 60배 이상의 높은 임계전력 성능을 보여 고출력에 적합함을 확인하였다. 그리고 1단의 T-junction과 2, 3단의 MagicT 결합기를 조합하여 소형화를 이루고, 삽입손실을 줄여 결합 효율을 최적화 하였다. 제작된 도파관 결합기는 16dB 이상의 격리도와 86.2% 의 결합 효율을 얻었다.

• Steel and Composite Structures
• /
• 제50권3호
• /
• pp.265-280
• /
• 2024

The collapse behavior observed in single-story beam-column assembly (SSBCA) do not accurately represent the actual overall stress characteristic of multi-story frame structure (MSFS) under column loss scenario owing to ignoring the interaction action among different stories, leading to a disconnection between the anti-collapse behaviors of "components" and "overall structures", that is, the anti-collapse performance of frame structures with two different structural scales has not yet formed a combined force. This paper conducts a numerical and theoretical study to explore the difference of the collapse behaviors of the SSBCA and MSFS, and further to reveal the internal force relationships and boundary constraints at beam ends of models SSBCA and MSFS. Based on the previous experimental tests, the corresponding refined numerical simulation models were established and verified, and comparative analysis on the resistant-collapse performance was carried out, based on the validated modeling methods with considering the actual boundary constraints, and the results illustrates that the collapse behaviors of the SSBCA and MSFS is not a simple multiple relationship. Through numerical simulation and theoretical analysis, the development laws of internal force in each story beam under different boundary constraints was clarified, and the coupling relationship between the bending moment at the most unfavorable section and axial force in the composite beam of different stories of multi story frames with weld cover-plated flange connections was obtained. In addition, considering the effect of the yield performance of adjacent columns on the anti-collapse bearing capacities of the SSBCA and MSFS during the large deformation stages, the calculation formula for the equivalent axial stiffness at the beam ends of each story were provided.