• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.68-72
• /
• 1991

In this study, to improve temperature stability 0.05 Pb(Sn$\_$$\frac{1}{2}$/Sb$\_$$\frac{1}{2}$/O$_3$ - 0.35PbTiO$_3$ - 0.60PbZrO$_3$ + 0.4[wt%]MnO$_2$ piezoelctric oeramics of low dielectric constant and large mechanical quality factor were manufactured with the addition of Cr$_2$O$_3$by Hot Press method. And the SAW delay line was fabricated and the propagation characteristics of SAW was investigated, and the SAW filter was fabricated on C4 added by 0.2[wt%] Cr$_2$O$_3$and its frequency characteristics was investigated. The specimen, whose propagation characteristics of surface acoustic wave were the best, was C4 added by 0.2[wt%] Cr$_2$O$_3$, and its electromechanical coupling factor(ks$^2$) was 3.11[%] and its temperature coefficient of the center frequency (C$\_$fo/) was -21.27[ppm/$^{\circ}C$]. The 31[MHz] SAW IF filter of C4 scarcely had diffraction phenomena and its group delay time was 1.4673 ${\pm}$40[ns] in the pass band, and the insertion loss was -24.419[dB] on no impedance matching.

• Journal of the Optical Society of Korea
• /
• v.19 no.1
• /
• pp.7-12
• /
• 2015

Up to ${\sim}520{\mu}J$ broadband mid-infrared (IR) supercontinuum (SC) generation in telecommunication multimode fiber (MMF) directly pumped by a $2.054{\mu}m$ nanosecond Q-switched Tm, $Ho:YVO_4$ laser is demonstrated. An average output power of 3.64 W is obtained in the band of ~1900 to ~2600 nm, and the corresponding optic-to-optic conversion efficiency is 67% by considering the coupling efficiency. The spectrum has extremely high flatness with negligible intensity variation (<2%) in the wavelength interval of ~2070 to ~2475 nm. The SC long-wavelength edge is limited by the silicon glass material loss, and by optimizing the MMF length, the SC spectrum could extend out to ${\sim}2.6{\mu}m$. The output SC pulse shapes are measured at different output powers, and no splits are found. The SC laser beam is nearly diffraction limited with an $M^2=1.15$ in $2.1{\mu}m$ measured by the traveling knife-edge method, and the laser beam spot is monitored by an infrared vidicon camera.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.61-68
• /
• 2007

Using modal transmission-line theory (MTLT), itexplores rigorously the polarization characteristics of TE-TM mode optical polarized beamsplitter with misaligned input interface. To verify the validity of the approach proposed in this paper, a novel polarization condition is defined, and it compares and evaluates with the polarization condition of coupled-mode theory (CMT) used widely. The numerical results reveal that the discontinuity of misaligned input interface has nothing to do with the polarization condition of beamsplitter. Furthermore, the condition of CMT is no longer effective at the asymmetric guiding structures with strong power coupling.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.4
• /
• pp.13-18
• /
• 2012

By the need for high-speed data transmission in PCB, the studies on the optical PCB has been conducted with optical interconnection and its packaging technology. Particularly, the polymer-based optical interconnection has been extensively studied with the advantages such as cost-effective and ease of process. For high-efficiency and passive alignment, the studies were performed using the 45 degree mirrors, MT connector, and etc. In this work, integrated PLC device and fiber alignment array block was fabricated by using imprint technology to solve the alignment and array problem of optical device and the optical fiber. The fabricated integrated block for optical interconnection of PLC device has achieved higher precision of decreasing the dimensional error of the patterns by optimization of process and its insertion loss has an average value of 4.03dB, lower than criteria specified by international standard. In addition, a optical waveguide with built-in lens has been proposed for high-efficiency and passive alignment. By simulation, it was confirmed that the proposed structure has higher coupling efficiency than conventional no-lens structure and has the broad tolerance for the spatial offset of optical waveguide.

• Korean Journal of Optics and Photonics
• /
• v.10 no.5
• /
• pp.419-423
• /
• 1999

Optical filters utilizing the evanescent filed coupling between the side polished fiber and polymer planar waveguide were fabricated and optical properties of the devices were measured. A scheme for reducing polarization dependent properties of the device was proposed and demonstrated experimentally. Our measurement results showed that resonance wavelengths and filtering depth of the optical filters can be determined by adjusting thickness of planar waveguide and polishing depth of the fiber. The device fabrication procedure including fiber polishing steps and formation of polymer planar waveguide were described. The optical characteristics of fabricated optical filers were that 3 dB bandwidth was 15 nm, the resonance wavelength difference between the TE and TM polarized response was less then 2 nm, and insertion loss was less then 0.2 dB. The measured resonance wavelength drift dut to the variation of ambient temperature was -0.35 nm/$^{\circ}C$.

• Carbon letters
• /
• v.25
• /
• pp.84-88
• /
• 2018

At present, an important research area is the search for materials that are compatible with CMOS technology and achieve a satisfactory response rate and modulation efficiency. A strong local field of graphene surface plasmon polariton (SPP) can increase the interaction between light and graphene, reduce device size, and facilitate the integration of materials with CMOS. In this study, we design a new modulator of SPP-based cycle branch graphene waveguide. The structure comprises a primary waveguide of graphene-$LiNbO_3$-graphene, and a secondary cycle branch waveguide is etched on the surface of $LiNbO_3$. Part of the incident light in the primary waveguide enters the secondary waveguide, thus leading to a phase difference with the primary waveguide as reflected at the end of the branch and interaction coupling to enhance output light intensity. Through feature analysis, we discover that the area of the secondary waveguide shows significant localized fields and SPPs. Moreover, the cycle branch graphene waveguide can realize gain compensation, reduce transmission loss, and increase transmission distance. Numerical simulations show that the minimum effective mode field area is about $0.0130{\lambda}^2$, the gain coefficient is about $700cm^{-1}$, and the quality factor can reach 150. The structure can realize the mode field limits of deep subwavelength and achieve a good comprehensive performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.3
• /
• pp.492-498
• /
• 2003

In this paper, We analyze the optimum bias conditions of cascode coupled microwave mixer for maximum conversion gain mixer. Microwave self-oscillating mixer by two GaAs MESFET cascode coupled, to upper GaAs MESFET operating as a oscillator with high Q dielectric resonator and the lower GaAs MESFET operated as a mixer with low noise and high conversion characteristics. As a result of experiments, cascode coupled microwave self oscillating mixer according to optimun bias shows an 5.92 dBm oscillating power, -132.0dBc/Hz @ 100KHz at 5.15GHz and 3dB conversion loss.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.2
• /
• pp.69-75
• /
• 2005

In order to improve the reliability of high voltage rotating machines and mold transformers, it is necessary to understand the breakdown mechanism and life assessment of the high voltage winding parts. Especially the on-line PD test provides the ability to monitor effects, such as slot discharge, internal discharge, and end-winding discharge without interrupting the electrical machines, this method has been proven the major testing technology. Capacitive couplers have been the most widely used sensors for the on-line partial discharge detection in rotating machines nowadays. This paper deals with the electrical characteristics and long-term reliability of a ceramic coupler(CC), which can be easily mounted into high voltage input terminal part, has been developed and tested to continuously measure PD activity during operating condition. This paper presents electrical characteristics (dielectric loss angle, capacitance, PD inception level, breakdown voltage, and frequency response bandwidth) and long-term life test result of the developed 6.6 kV class on-line ceramic coupling sensor. It was found that this sensor had good electrical characteristics to detect PD activity during the operating condition with its detection frequency band is between several and several tens MHz. Also, the voltage life of the 6.6kV class ceramic coupler was calculated over 60 years.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.30-30
• /
• 2008

Lead-free piezoelectric ceramics 0.97$(Na_{0.5}K_{0.5})NbO_3$-0.03Ba$(Ti_{1-x}Sn_x)O_3$ [NKN-BTS-x] ceramics doped with 1 mol% $MnO_2$ have been fabricated by a sintering technique with muffling. The $MnO_2$-doped NKN-BTS-x ceramics with x$\leq$0.2 have pure orthorhombic perovskite structure at room temperature. The dense microstructure was developed with grain growth as an increase of amount of Sn. Moreover, the addition of Sn was found to have a significant influence on piezoelectric properties. In particular, the $MnO_2$-doped NKN-BTS-0.1 ceramics showed improved piezoelectric properties of piezoelectric constant ($d_{33}$=145pC/N), relatively large electromechanical coupling factor ($k_p$=43%), dielectic constant (${\varepsilon}^T_{33}/{\varepsilon}_0$=676) dielectric loss (tan$\delta$=1.3%).

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.4
• /
• pp.5-8
• /
• 2009

In this paper, a high-quality low-temperature co-fired ceramic (LTCC) solenoid inductor using a solder ball and an air cavity on a silicon wafer for three-dimensional (3-D) system-in-package (SiP) is proposed. The LTCC multi-layer solenoid inductor is attached using Ag paste and solder ball on a silicon wafer with the air cavity structure. The air cavity is formed on a silicon wafer through an anisotropic wet-etching technology and is able to isolate the LTCC dielectric loss which is equivalent to a low k material effect. The electrical coupling between the metal layer and the LTCC dielectric layer is decreased by adopting the air cavity. The LTCC solenoid inductor using the solder ball and the air cavity on silicon wafer has an improved Q factor and self-resonant frequency (SRF) by reducing the LTCC dielectric resistance and parasitic capacitance. Also, 3-D device stacking technologies provide an effective path to the miniaturization of electronic systems.