• Journal of Astronomy and Space Sciences
• /
• v.24 no.4
• /
• pp.397-408
• /
• 2007

Diplexer is one of core devices needed to communicate with satellite using single ground antenna by separating uplink and downlink signal. This paper presents the design of the S-band diplexer for LEO TT&C application, especially for KOMPSAT (KOrea Multi-Purpose SATellite). To cope with requirements such as high handling power, low insertion loss, air-cavity resonator with high quality factor was considered as one of design drivers. Design was started with predicting unloaded Q and equivalent circuit from the structure of air-cavity resonator. For the convenience of adjustment, the coupling factor placed between resonators was estimated from COTSEM (Electro-Magnetic) simulator, EESOF $ADS^{TM}$, and expressed with 2-order polynomial regression. To improve the isolation between transmitting part (Tx) and receiving part (Rx), the inductive and capacitive attenuation poles were inserted between $4^{th}\;and\;6^{th}$ resonator respectively. The fabricated diplexer consists of two bandpass filters and each filter has eight resonants. From the measurement, it was shown that major requirements such as 0.5dB of insertion loss, 20dB of return loss and 100dB of isolation were fully satisfied within passband.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.3
• /
• pp.271-277
• /
• 2004

A Si(Silicon) MEMS(Micro Electro Mechanical System) package using a doped lossy Si carrier for CPW(Coplanar Waveguide) MMICs(Microwave and Millimeter-wave Integrated Circuits) is proposed in order to reduce parasitic problems of leakage, coupling and resonance. The proposed chip-carrier scheme is verified by fabricating and measuring a GaAs CPW on the two types of carriers(conductor-back metal, doped lossy Si) in the frequency from 0.5 to 40 ㎓. The proposed MEMS package using the lightly doped lossy(15 Ω$.$cm) Si chip-carrier and the HRS(High Resistivity Silicon, 15 ㏀$.$cm) shows the optimized loss and parasitic problems-free since the doped lossy Si-carrier effectively absorbs and suppresses the resonant leakage. The Si MEMS package for CPW MMICs has an insertion loss of only - 2.0 ㏈ and a power loss of - 7.5 ㏈ at 40 ㎓.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.101-104
• /
• 1998

We report some methods for measuring a LiNbO$_3$ optical phase modulator bandwidth. Since Mach-Zehnder waveguide type, one of methods for modulation bandwidth measurement, is comparatively simple and useful, it was adapted in this work. In order to confirm this method, the waveguide of single and Mach-Zehnder type were fabricated on the same wafer. The Mach-Zehnder interferometric waveguide and the single channel waveguide were used for the measurement of the phase modulator's driving voltage and bandwidth for device fabrications, respectively. Ti-860$\AA$ in-diffusion was achieved in a wet-bubbling oxygen environment at 105$0^{\circ}C$/8hours. LINbO$_3$ internal chips were pigtailed to PMF(polarization maintaining fiber)/SMF(single mode fiber) using an epoxy curing technique. Examined were optical properties such as an insertion loss, propagation loss and mode size, and the loss mechanism of optical coupling between an optical fiber and a waveguide was considered.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.32-39
• /
• 2013

All spacecraft components shall be checked for compatibility with vacuum using CVCM and TML in advance. CVCM and TML of the PZT-5 piezoelectric vibrator has to be less than 0.1% and 1.0% respectively. Also, it has less than $500ng/cm^2/hr$ of TQCM for vacuum bake-out test using high temperature and high vacuum. Thus, the piezoelectric vibrator may be employed in the vacuum environments. Finally, it can be confirmed that the characteristics change of the piezoelectric vibrator is less than 1% under vacuum environments. Also, the temperature dependency of the characteristics in the PZT-5 piezoelectric vibrator with the lateral mode was investigated in the range of $-100^{\circ}C$ to $90^{\circ}C$ using the thermal vacuum chamber to utilize the vibrator to the aerospace industries. As the results, at room temperature, the resonant and anti-resonant frequencies had the minimum value, whereas, the dielectric constant increased linearly from about 2500 to 7500 in the given temperature range. The mechanical loss decreased linearly from 0.08 to 0.03.

• Journal of information and communication convergence engineering
• /
• v.5 no.2
• /
• pp.150-154
• /
• 2007

Transponders of RFID system are classified as active or passive depending on the type of power supply they use. In passive transponders the data carrier has to obtain its power from the induced voltage. The induced voltage is converted into direct current using a low loss bridge rectifier and then smoothed. In practice, the induced voltage in the transponder coil is variable according to the coupling coefficient k and the load resistance ($R_L$). Therefore, the rectified voltage is unstable and the transponder of RFID is unstable sometimes. In this paper, a voltage-dependent shunt resistor ($R_s$) circuits are designed and inserted in parallel with the load resistance of RFID transponder in order to improve the stability of power.

• ETRI Journal
• /
• v.26 no.3
• /
• pp.262-264
• /
• 2004

We investigate the characteristics of a wideband and high-gain cavity-backed slot antenna in terms of the reflection coefficients, radiation patterns, and gain. A cavity-backed slot antenna structure includes baffles, reflectors, and thick ground planes. The measured gain and bandwidth of a 10-dB return loss in a cavity-backed $2{\times}2$ array slot antenna with $h_1=2 $mm, d=2 mm are 15.5 dBi and nearly 27%, respectively, at 42 GHz. Baffles and reflectors are used to increase antenna gain, thus reducing the coupling among the slots on the thick ground plane.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2679-2682
• /
• 2012

A simple one-pot synthesis of two derivatives of 1,4-dihydropyridines has been described under reflux conditions using copper iodide nanoparticles (CuI NPs) as a catalyst in high yields. This method demonstrated four-component coupling reactions of aldehydes and ammonium acetate via two pathways. In one route, the reaction was performed using 2 eq ethyl acetoacetate while in the other one 1 eq ethyl acetoacetate and 1 eq malononitrile were used. The CuI NPs was reused and recycled without any loss of activity and product yield. It is noteworthy to state that wide range of the 1,4-dihydropyridines have attracted large interest due to pharmacological and biological activities.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.26-27
• /
• 2011

This paper focuses on the zero-voltage/zero current transition voltage equalization circuit for the series connected battery cell. By adding auxiliary resonant cells at the main switching devices such as MOSFET or IGBT, zero current switching is achieved and turned off loss of switching elements is eliminated and by the voltage/second balancing of the inductor, zero voltage switching can be applied to switching element. Transformer coupling between battery cells and ZVZCT (Zero Voltage Zero Current Transition) switching method allow the fast balancing speed and high frequency operation, which reduces the size and weight of the circuit. The validity of the battery equalization is further verified using simulation involving four lithium-ion battery cell models.

• Journal of the Korean Ceramic Society
• /
• v.25 no.5
• /
• pp.523-531
• /
• 1988

The dielectric and piezoelectric properties with compositions in Pb(Ni1/3Nb2/3)O3-PbTiO3-PbZrO3-(PNN-PT-PZ)solid solution ceramics were investigated. In this study, the compsition ranges were 30 PNN 45mole%, 20 PT 50mole% and 50 PZ5mole%. As PT fraction were increased the grain size was increased and the fired density was decreased, but the changes of PNN fraction had no effect on the grain size. The Curie temperature was increased when PT and PNN fraction were increased. The displacement was increased but had a great hysteresis loss when PT fraction was increased. In morphotropic phase boundary, the maximum piezoelectric and electromechanical coupling factor were indicated. Morphotropic phase boundary(MPB) was 34 PT 36mole% in chang of compositions.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.12
• /
• pp.1018-1027
• /
• 2003

This study treats the analysis of the performance and the design of plume abatement wet/dry cooling tower with dry type heat exchanger using a numerical method. A two-dimensional analysis is performed using the finite volume method for mechanical draft counterflow and crossflow tower. For a coupling problem between water and air system, a turbulent two phase flow is considered. Effectiveness-NTU method is used for modeling of the dry type heat exchanger. The parameter change simulations of the outer wall shape, the relative flowrate of air, and attachment of an air mixer are performed to examine the effect on plume abatement. It is found that if the relative air flowrate ratio and the adequate air mixer type are chosen well in addition to the ratio of water to air flowrate, the loss of the cooling capacity and the additional cost are reduced and the plume is abated.