• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2173-2178
• /
• 2008

Railroad is the major factor of vibration source in railway vehicles, and it must carefully maintained the original condition to secure the safety and good ride comfort of passenger. Measuring the condition of rail irregularities such as surface, alignment, gauge, twist and cant etc is required to maintain the good performance of railroad. Currently, the various rail irregularity measurement systems(EM120, ROGER1000K and the Total Rail Irregularity Measurement system of Korea High Speed Train) are operated in Korea to estimate the rail irregularity. It is hard to verify the correlation of one rail irregularity data of a measurement system with the other, because they have been adopted different rail irregularity estimation methods. The best method securing the reliability of the irregularity data is the direct confirmation on the ground where the measurement system had detected as a fault section, but it is impossible to apply all sections simultaneously due to limitation of time, labor, cost and equipments. There is a method to secure the reliability of the data by using acceleration values. Rail irregularities, the major factor of vibration in railway vehicle, are transmitted to the vehicle acceleration through masses, springs, dampers and joints as the system dynamic formation. In this study, Transition Function has been adopted by using the rail irregularity and the acceleration value regarding as input & output parameters respectively. It has been verified by comparing the analyzed results with real measured irregularity data from the Total Rail Irregularity Measurement system of Korea High Speed Train. Also various methods has been accomplished to verify the correlation between rail irregularities and acceleration values.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1426-1440
• /
• 2008

In Korea, the concentration for the use of urban railroads is comparatively high during peak hours. In case of road traffic, overcrowdness leads the increase of total travel time and cost naturally but this does not happen in railroad systems because of fixed operational interval. Thus, passenger's disutility is generated physically and mentally from congestion increment. The increase of railroad capacity from new transit lines and expansion of existed lines contributes traveler's comfort benefits to rising. However, present evaluation guidelines for feasibility studies of road and railroad projects do not include any valuation methodology about passenger's comfort benefits. Therefore, in this research, various factors affecting comfort benefits are reviewed and stated preference survey is performed in order to estimate traveler's comfort benefits for congestion reduction. In addition, willingness to pay for congestion avoidance is calculated from that stated preference survey based on Tobit Model. As a result, detailed unit for willingness to pay according to congestion reduction is proposed in this study.

• Journal of the Korean Society for Railway
• /
• v.12 no.3
• /
• pp.348-356
• /
• 2009

The objective of this paper is to estimate the DMT utility function for the transportation mode choice using SP survey. With the freight OD data the estimated utility function can be used as a basic data for forecasting DMT market. 3 alternatives of transportation mode are considered in SP survey; railway, road and DMT. The utility functions are developed according to the freight items, which are container, steel and chemical product. In this study the attribute variable are chosen as time, cost and reliability. The number of level for attribute variables are 3. The high valve is determined as +10% above the standard and the low value -20% below the standard.

• Atmosphere
• /
• v.20 no.2
• /
• pp.187-194
• /
• 2010

We estimate the economic benefit of weather modification (precipitation enhancement and fog dissipation) by assuming its operation for the considered regions. Based on the statistical data, the economic benefit of the virtually operational precipitation enhancement experiments for the Andong and Imha basins, where the natural precipitation is relatively lack in South Korea, is calculated 348 for the water resources, 22,458 for forest fire prevention, and 28,458 million won/year for the drought relief. The benefit of the fog dissipation operation for the Incheon International Airport is estimated 7,365 million won/year for the flight delay due to fog. The calculated ratio of benefit to cost for precipitation enhancement operation for the basins is 14.07, which is comparable to that conducted in other countries.

• Environmental and Resource Economics Review
• /
• v.29 no.2
• /
• pp.247-270
• /
• 2020

The value of a statistical life (VSL) plays a very important role in estimating the benefits of environmental policy. It is used, for example, as a unit of monetization of health benefits resulting from the reduction of air pollutants, which is the basis of cost-benefit analysis of policies. The VSL can be defined as the value that people of each society are willing to pay to reduce the risk of death, so the value should reflect the characteristics of its members. In this study, we apply a choice experiment with 3,081 respondents collected through a web survey were divided into two samples according to the type of questions. Among the various estimates, the most appropriate estimate of the VSL is about 1.3 billion won from 1,528 sample, which is similar to the results of the meta-analysis using estimates from prior studies conducted in Korea. In addition, this study shows that a private prevention program is preferred to reduce the risk of death from cancer rather than a public program.

• Environmental Engineering Research
• /
• v.11 no.3
• /
• pp.156-163
• /
• 2006

In this study, substrate removal characteristics were analyzed to reduce the cost of external carbon dosage at Sudokwon Landfill Site Management Corporation in Korea by utilizing oxygen uptake rate (OUR) and nitrate uptake rate (NUR) tests. To estimate and evaluate the substrate removal characteristics obtained by the batch tests, the lab-scale MLE process was operated. By-products of J Co. (sugar manufactory) and S Co. (fine chemical industry) were selected as the concerned carbon sources through a comparison of carbon and nitrogen contents. MeOH was tested as a control experiment. Until the steady state, the fraction of $RBDCOD_{OUR}$ concentration to COD concentration of J Co., S Co. by-products and MeOH increased and reached levels of 98%, 82%, and 100%, respectively. During the 20th operating day, the fraction of $RBDCOD_{NUR}$ concentration to COD concentration was 95%, 81%, and 83%, respectively. These fractions of $RBDCOD_{NUR}$ concentration to $RBDCOD_{OUR}$ concentration increased according to acclimation periods and reached levels of 99%, 97%, and 81%, respectively, on the 20th day. The results obtained from the lab-scale MLE process operation using the concerned carbon sources as external carbon were similar to that observed by OUR and NUR tests.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.319-324
• /
• 2003

In general industrial rotating machinery is operated under 3,600 rpm as rotating speed and designed to have critical speed that is above operating speed. So, there was no problem to operate rotating machine under critical speed. But nowadays, they should be operated more than the frist critical speed as usual with the trend of high speed, large scale and hish precision in industries. In case of the large rotor assembly as the trend of large scale, using fitting method of disk or cylinder on shaft is rising for the convenience of assembly and cutting down of manufacturing cost. The shrink fitting is used to assemble lamination part on shaft for manufacturing of rotor of motor or generator in many cases and also is widely used for other machinery. In rotating system, which is compose of rotor and bearing, the critical speed is determined from inertia and stiffness for the rotor and bearings. In case of fitting assembly, analysis and design of the rotor is not easy because the rotor stiffness is determined depend on a lot of factors such as shaft material/dimension, disk material/dimension and assembled interference etc. Therefore designer who makes a plan for hish-speed rotating machine should design that the critical speed is located out of operating range, as dangerous factors exist in it. In order to appropriate design, an accurate estimation of stiffness and damping is very important. The stiffness variation depend on fitting interference is a factor that changes critical speed and if it's possible to estimate it, that Is very useful to design rotor-bearing system. In this paper, the natural frequency variation of the rotor depends on fitting interference between basic shaft and cylinder is examined by experimentation. From the result, their correlation is evaluated quantitatively using numerical analysis that is introduced equivalent diameter end the calculation criteria is presented for designer who design fitting assembly to apply with ease for determination of appropriate interference.

• Journal of Ginseng Research
• /
• v.36 no.2
• /
• pp.205-210
• /
• 2012

For quality control of components in Korean red ginseng powder and extract, a new method for simultaneous quantification of 12 ginsenosides ($Rg_1$, Re, Rf, $Rh_1$, $Rg_2$[S], $Rg_2$[R], $Rb_1$, Rc, $Rb_2$, Rd, $Rg_3$[S], and $Rg_3$[R]) was studied. Compared to the official method for quantification of marker substances (ginsenosides $Rg_1$ and $Rb_1$), the proposed methods were guaranteed by in-house method validation. Several criteria such as linearity, specificity, precision and accuracy were evaluated. For red ginseng powder, recovery (averaging 95% to 105%) was calculated, and analysis of variance was carried out to estimate the relative standard deviation (0.20% to 2.12%). For red ginseng extract, the average recovery rate was 90% to 99% and the relative standard deviation was 0.39% to 2.40%. These results indicate that the proposed method could be used in the laboratory for determination of 12 ginsenosides in red ginseng powder and extract. In addition, this method was found to be suitable for quality control of ginseng products and potentially offer time and cost benefits.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.1
• /
• pp.24-30
• /
• 2016

The accuracy of small and low-cost CCD cameras is insufficient to provide data for precisely tracking unmanned aerial vehicles (UAVs). This study shows how a quad rotor UAV can hover on a human targeted tracking object by using data from a CCD camera rather than imprecise GPS data. To realize this, quadcopter UAVs need to recognize their position and posture in known environments as well as unknown environments. Moreover, it is necessary for their localization to occur naturally. It is desirable for UAVs to estimate their position by solving uncertainty for quadcopter UAV hovering, as this is one of the most important problems. In this paper, we describe a method for determining the altitude of a quadcopter UAV using image information of a moving object like a walking human. This method combines the observed position from GPS sensors and the estimated position from images captured by a fixed camera to localize a UAV. Using the a priori known path of a quadcopter UAV in the world coordinates and a perspective camera model, we derive the geometric constraint equations that represent the relation between image frame coordinates for a moving object and the estimated quadcopter UAV's altitude. Since the equations are based on the geometric constraint equation, measurement error may exist all the time. The proposed method utilizes the error between the observed and estimated image coordinates to localize the quadcopter UAV. The Kalman filter scheme is applied for this method. Its performance is verified by a computer simulation and experiments.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.3
• /
• pp.330-335
• /
• 2012

Brushless doubly-fed machine (BDFM) doesn't use brush and slip ring, and has advantages such as high system reliability, small capacity of its frequency converter, low system cost, adjustable power factor and speed, etc. At the same time, it has good applicable potentials on the variable frequency motors and the variable speed constant frequency generators. However, due to the complicacy and particularity of BDFM in the structure and operating mechanism, the effect of magnetic field modulation directly influences the operating efficiency of BDFM. To study the effect of different cage rotor structures on the magnetic field modulation of BDFM, the rotor magnetomotive force (MMF) of BDFM with cage rotor is studied by the analytical method. The components and features of rotor harmonic MMFs are discussed. At the same time, the method to weaken the higher harmonics is analyzed by the theoretic formulae. Furthermore, the magnetic field modulation mechanism is expounded on in detail and the relationship between the magnetic field modulation effect and the operating efficiency of BDFM is established. And then, a new method for estimating the magnetic field modulation effect is proposed. At last, the magnetic field modulation effects of four BDFM prototypes with different cage rotor structures are compared by the MMF analysis and the efficiency data of electromagnetic design. The results verify the effectiveness of the new method for estimating the magnetic field modulation effect of BDFM with cage rotor.