• Journal of Bio-Environment Control
• /
• v.11 no.1
• /
• pp.5-11
• /
• 2002

In this study, new development of natural ventilation window was accomplished to control environment of greenhouse with no use of farced ventilation during hot season. The ventilation effect of developed ventilation window was investigated in experimental greenhouse which was designed using side wall panel and folding type panel fur natural ventilation. Folding panel type ventilation window was designed to open upper part of the side wall and top of the roof using two hinges which are located bottom of the side wall and the roof panel to grab one side of each panels and guide the other side along with the guidance rail. Developed ventilation window has top ventilation part with maximum moving distance X=ι (1-cos$\theta$)=848.5 mm and side ventilation part with maximum moving distance Y=ι/2 $\times$sin$\theta$=1,184.4 mm at 45$^{\circ}$ of theoretical opening angle. It took 4.5 minutes to open roof vent fully and temperature at 1.2 and 0.8 m height decreased after 1 minute from starting opening and became equilibrium state maintaining 3-4$^{\circ}C$ difference after 2 minutes from complete opening. Air exchange rate was 15.2~39.3 h$^{-1}$ which was more than 10~15 h$^{-1}$ of continuous type and Venlo type greenhouse. The descent effect of temperature by ventilation windows was two times higher than Venlo type greenhouse.

• Journal of radiological science and technology
• /
• v.32 no.2
• /
• pp.177-182
• /
• 2009

Purpose : This study presents the optimization of flip angle (FA) to obtain higher contrast to noise ratio (CNR) and lower specific absorption rate (SAR). Materials and Method : T1-weighted images of the cerebrum of brain were obtained from 50$^\circ$ to 130$^\circ$ FA with 10$^\circ$ interval. Signal to noise ratios (SNRs) were calculated for white matter (WM), gray matter (GM), and background noise. The proper FA was analyzed by T-test statistics and Kruskal-wallis analysis using R1 = 1- exp ($\frac{-TR}{T1}$) and Ernst angle cos $\theta$ = exp ($\frac{-TR}{T1}$). Results : The SNR of WM at 130$^\circ$ FA is approximately 1.6 times higher than the SNR of WM at 50$^\circ$. The SNR of GM at 130$^\circ$ FA is approximately 1.9 times higher than the SNR of GM at 50$^\circ$. Although the SNRs of WM and GM showed similar trends with the change of FA values, the slowdown point of decrease after linear fitting were different. While the SNR of WM started decreasing at 120$^\circ$ FA, the SNR of GM started decreasing at less than 110$^\circ$. The highest SNRs of WM and GM were obtained at 130$^\circ$ FA. The highest CNRs, however, were obtained at 80$^\circ$ FA. Conclusion : Although SNR increased with the change of FA values from 50$^\circ$ to 130$^\circ$ at 3T SE T1WI, CNR was higher at 80$^\circ$ FA than at the usually used 90$^\circ$ FA. In addition, the SAR was decreased by using smaller FA. The CNR can be increased by using this optimized FA at 3T MR SE T1WI.

• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.21 no.1
• /
• pp.1-6
• /
• 2001

This experiment was conducted to evaluated the effect of maturity at harvest on the changes in quality of round baled rye silage at forage experimental field of Grassland and Forage Crops Division, National Livestock Research Institute, RDA, Suwon in 1998. The experimental design was a split-plot design with three replications. The main plots were three different harvest stages : boot, heading and flowering stages, and the subplots were days after ensiling : 1, 2, 3, 5, 10, 30, 45, and 60 days. The wilting period of boot, heading and flowering stages were 1, 0.5 and 0.5 days, respectively. The final pH of rye silage was higher in the order of flowering, boot and heading stages. And pH of flowering stage began to change at early fermentation period, but that of boot and heading stages was delayed 1~2 days. Ammonia-N content of boot stage was highest. and that was increased as fermentation progressed. But Ammonia-N of heading stage was decreased to 30 days. then that was increased after 45 days fermentation. Among fermentation periods, inside temperature of deep place was not affected by external temperature. And that of deep place was increased to 3$0^{\circ}C$ at early fermentation. then decreased as fermentation progressed. However surface temperature was affected by external temperature after 10 days. Acetic acid content was not changed with 5 days by harvest stages, but that of boot stage was increased after 10 days. Butyric acid of boot stage was increased after 5 days. but that of heading stage was increased after 10 days. However lactic acid was increased from 1~2% to 6~8%. Lactic acid bacteria (LAB) of heading and flowering stages were highest at 5 days fermentation, and that of boot stage was highest at 10 days fermentation. The results of this study indicate that fermentation of round baled rye silage occur within 5 days. Therefore, any modification should be applied with an 5 days for high quality of round baled rye silage.

• The Journal of the Petrological Society of Korea
• /
• v.26 no.3
• /
• pp.297-309
• /
• 2017

Jurassic granite from Geochang was analysed with respect to the characteristics of the rock cleavage. The comprehensive evaluation for rock cleavages was performed through the combination of the 16 parameters derived from the enlarged photomicrographs of the thin section and the spacing-cumulative frequency diagrams. The results of analysis for the representative values of these spacing parameters with respect to the rock cleavage are summarized as follows. First, the above parameters can be classified into group I (spacing frequency (N), total spacing ($1m{\geq}$), constant (a), exponent (${\lambda}$), slope of exponential straight line (${\theta}$), length of line (oa') and trigonometric ratios ($sin{\theta}$, $tan{\theta}$) and group II (mean spacing (Sm), difference value between mean spacing and median spacing (Sm-Sme), density (${\rho}$), lengths of lines (oa and aa'), area of a right-angled triangle (${\Delta}oaa^{\prime}$) and trigonometric ratio($cos{\theta}$). The values of the 8 parameters belonging to group I show an order of H(hardway, H1+H2)

• Journal of the Korean Vacuum Society
• /
• v.17 no.4
• /
• pp.331-340
• /
• 2008

A method of measuring the current and voltage is suggested in the circuit of cold cathode fluorescent lamps (CCFLs) which are driven at a high frequency of $50{\sim}100\;kHz$ and a high voltage of several kV. It is difficult to measure the current and voltage in the lamp circuit, because the impedance of the probe at high voltage side causes the leakage current and the variation of luminance. According to the analysis of equivalence circuit with the probe impedance and leakage current, the proper measuring method is to adjust the input DC voltage and to keep the specific luminance when the probe is installed at a high voltage circuit. The lamp current is detected with a current probe or a high frequency current meter at the ground side and the voltage is measured with a high voltage probe at the high voltage side of lamp. The lamp voltage($V_C$) is measured between the ballast capacitor and the lamp electrode, and the output voltage($V_I$) of inverter is measured between inverter output and ballast capacitor. As the phases of lamp voltage($V_C$) and current ($I_G$) are nearly the same values, the real power of lamp is the product of the lamp voltage($V_C$) by the lamp current($I_G$). The measured value of the phase difference between inverter output voltage($V_I$) and lamp current($I_G$) is appreciably deviated from the calculated value at $cos{\theta}=V_C/V_I$.

• Korean Journal of Poultry Science
• /
• v.46 no.2
• /
• pp.65-75
• /
• 2019

A number of Korean native chicken(KNC) populations were registered in FAO (Food and Agriculture Organization) DAD-IS (Domestic Animal Diversity Information Systems, http://www.fao.org/dad-is). But there is a lack of scientific basis to prove that they are unique population of Korea. For this reason, this study was conducted to prove KNC's uniqueness using 25 Microsatellite markers. A total of 548 chickens from 11 KNC populations (KNG, KNB, KNR, KNW, KNY, KNO, HIC, HYD, HBC, JJC, LTC) and 7 introduced populations (ARA: Araucana, RRC and RRD: Rhode Island Red C and D, LGF and LGK: White Leghorn F and K, COS and COH: Cornish brown and Cornish black) were used. Allele size per locus was decided using GeneMapper Software (v 5.0). A total of 195 alleles were observed and the range was 3 to 14 per locus. The MNA, $H_{\exp}$, $H_{obs}$, PIC value within population were the highest in KNY (4.60, 0.627, 0.648, 0.563 respectively) and the lowest in HYD (1.84, 0.297, 0.286, 0.236 respectively). The results of genetic uniformity analysis suggested 15 cluster (${\Delta}K=66.22$). Excluding JJC, the others were grouped in certain cluster with high genetic uniformity. JJC was not grouped in certain cluster but grouped in cluster 2 (44.3%), cluster 3 (17.7%) and cluster8 (19.1%). As a results of this study, we can secure a scientific basis about KNC's uniqueness and these results can be use to basic data for the genetic evaluation and management of KNC breeds.

• Korean Journal of Soil Science and Fertilizer
• /
• v.17 no.1
• /
• pp.12-17
• /
• 1984

In order to find out the effects of soil conditioner treatment on the water movement in sandy loam and silt loam soils were treated with two different kinds of soil conditioners, hydrophobic Bitumen 0.4% or hydrophillic Uresol 0.6%, and the changes of wetting angle (soil-water contact angle), penetrability and diffusivity were measured. The results were summarized as follows: 1. Uresol 0.6% treatment decreased the wetting angle of sandy loam more than $10^{\circ}$, but there was no big difference in silt loam. 2. Sandy loam soil was changed to almost hydrophobic and the wetting angle of silt loam soil was increased to $84.9^{\circ}$ as compared to $76.0^{\circ}$ of untreated soil by Bitumen 0.4% treatment. 3. By Uresol treatment, penetrability of sandy loam was doubled but there was not difference in silt loam, and it was decreased to half in two soils by Bitumen treatment. 4. A significant positive correlation between penetrability and the cosine of wetting angle was recognized. 5. Soil water diffusivity was greatly changed by soil conditioner treatment, and the big differences were appeared at lower soil moisture content.

• Journal of the Korean Society of Costume
• /
• v.30
• /
• pp.85-99
• /
• 1996

This study has been made to examine the symbolic meaning of our traditional costume colours based on the theory of yin-yang Wu-hsing the interaction of yin and yang with the rotation of the five agents wood firt earth metal and waters. Presenting the spirt and the life of our race the costume culture has been keep-ing its own systematic symbol. Being sensible the colour has to be under-stood as the colour sense therefore the cos-tume colour has begun to have the symbolic meaning with the feeling or the mental value. According to the theory of yin-yang wu-hsing the costume colour has presented our racial sprit way of thinking and way of life for a long time and it has become the tra-ditional culture at last. Based on the doctrine of cosmic harmony through the motion of yin and yang or the passive and active elements are their five agents form the material force of everything. The order of nature has its counterpart in five symbolic costume colours wood-blue ; fire-red: earth-yellow; metal-white: water-black. The five colours are called the primary colours. which produce the next compound colours. Accepted in the social system as well as the social stats the costume colour has set up systematically. The theory of Yin-yang Wu-hsing has given the five colours the symbolic meanings and its mainstream has been the function of Sangsaeng and Sangeuk which are genera-ted by the power of virture. The former is mu-tually beneficial while the latter destructive. The colour as a costume colour has been made distinction between the colour of the up-per classes and the colour of the middle and lower classes and the specific colour has presented the symbolic meanings. The yeollow the red and the purple have been regarded as the colour of king queen and upper classes Being the colour recognition the costume colour has been established by the society and the race generally Implied the spiritual elements the colour recognition could select the lucky colour in accordance with one's des-tiny. Besides the colour recognition has begun to appear as the racial costumes to protect the society and to pray for good fortune. According to the theory of Yin-yang Wu-hsing the costume colour has been forming through our long history and has become our costume culture. Therefore the colour of the costume has signified not only the colour sense but also the important symbolic meanings.

• BMB Reports
• /
• v.40 no.4
• /
• pp.517-524
• /
• 2007

There were many different families of zinc finger proteins that contained multiple cysteine and/or histidine residues and used zinc to stabilize their folds. The classical C2H2 zinc finger proteins were the founding members of this superfamily and were among the most abundant proteins in eukaryotic genomes. C2H2 proteins typically contained several C2H2 fingers that made tandem contacts along the DNA. Here we reported a novel C2H2 type zinc finger gene, ZNF438, which encoded 828 amino acids that formed five zinc finger domains. Bioinformatics analysis revealed that the ZNF438 was mapped to human chromosome 10p11.2 and shared 62% identity with rat and mouse homologues. RT-PCR analysis indicated that it was ubiquitously expressed in 18 human adult tissues. With immunofluorescence assay, it was shown that the exogenous Flag-tagged ZNF438 was located in nucleus of COS-7 cells. To further explore the function of ZNF438, we examined the transcriptional activity of ZNF438 protein by transfecting recombinant pM-ZNF438 into mammalian cells. The subsequent analysis based on the duel luciferase assay system showed that ZNF438 was a transcriptional repressor.