• Tribology and Lubricants
• /
• 제7권2호
• /
• pp.46-50
• /
• 1991

The Frictional behavior in single crystal (111) p-type silicon as influenced by electolytic solutions have been studied. Linear scratching by diamond indentor was carried out to show the variation of friction between silicon and diamond indentor immersed in electrolytic solutions. The results indicate that concentration of the solutions influence the fricational coefficient. In addition there is a correlation between measured zeta-potential and frictional coefficients. The zeta-potential in various concentrations was measured to estimate the variation of the Peierls energy. The proposed model predicts a minimum frictional coefficient near a concentration of $10^{-3}$ M/l NaOH in deionized water and explains the chemomechanical effect observed in this study.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.425-436
• /
• 1987

본 연구에서는 강제대류가 있는 층류막비등유동을 벽면온도와 주수속도를 변 화시키며 수치해석하여 열전달계수와 유동특성을 구하였고, 열력학적 상태량들을 일정 하다고 가정하는 경우가 열전달계수에 어떠한 영향을 미치는가를 검토한 결과, 열전달 계수는 주수속도에는 큰 영향을 받지 않으나, 벽면온도와 열력학적 상태량의 변화에는 상당히 큰 영향을 받는 것으로 나타나고 있다.

• 대한기계학회논문집A
• /
• 제37권2호
• /
• pp.177-185
• /
• 2013

본 논문에서는 윤중감소를 고려한 이론적 새로운 탈선계수 모델을 제시한다. 본 탈선계수 모델은 열차 충돌 원인 탈선현상을 예측할 수 있는 단일 윤축의 이론적 탈선모델을 바탕으로 도출한다. 현재 국내 탈선규정에서는 플랜지 각이 $60^{\circ}$ 이고 마찰계수가 0.3인 조건을 나달식에 적용하여 탈선계수를 구한 후 안전율을 적용하여 0.8을 규정하고 있으나, 플랜지 각이 변경되면 이론적 설명이 부족하게 된다. 따라서 제시한 탈선계수 이론모델을 이용하여 탈선계수 규정 값 0.8을 이론적으로 접근해본다. 또한 국내탈선규정에서 윤중 감소율을 50%까지 허용하고 있으나 명확한 규정근거를 제시하고 있지 않다. 따라서 윤중 규정 50%감소와 탈선계수 규정 값 0.8과의 상관 관계를 앞서 제시한 탈선계수 이론모델을 이용하여 이론적으로 규명한다. 마지막으로 동역학 시뮬레이션을 이용하여 탈선계수 이론모델의 타당성을 입증한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권3호
• /
• pp.500-508
• /
• 2004

The heat transfer coefficients during gas cooling process of carbon dioxide in a horizontal tube were investigated. The experiments are conducted without oil in the refrigerant loop. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater, and a gas cooler(test section). The water loop consists of a variable-speed pump, an isothermal tank, and a flow meter. The gas cooler is a counterflow heat exchanger by cooled water flowing in the annulus. The $CO_2$ flows in the horizontal stainless steel tube. which is 9.53mm in O.D. and 7.75mm in I.D. The gas cooler is 6 [m] in length. which is divided into 12 subsections, respectively. The experimental conditions considered in the study are following range of variables : refrigerant temperature is between 20 and $100^{\circ}C$. mass fluxes ranged from 200 to 400kg/($m^2$.s), average pressure varied from 7.5 to 10.0MPa. The main results were summarized as follows : The friction factors of $CO_2$ in the gas cooler show a relatively good agreement with those predicted by Blasius' correlation. The local heat transfer coefficient in the gas cooler has compared with most of correlations, which are the famous ones for forced convection heat transfer of turbulent flow. The results show that the local heat transfer coefficient of gas cooler agrees well with the correlation by Bringer-Smith except that at the region near pseudo critical temperature. while that at the near pseudo critical temperature is higher than the correlation.

• Bulletin of the Korean Chemical Society
• /
• 제23권3호
• /
• pp.447-453
• /
• 2002

In this paper we have presented the results of thermodynamic, structural, and dynamic properties of model systems for liquid benzene, toluene and p-xylene in an isobaric-isothermal (NpT) ensemble at 283.15, 303.15, 323.15, and 343.15 K using molecular dynamics (MD) simulation. This work is initiated to compensate for our previous canonical (NVT) ensemble MD simulations [Bull. Kor. Chem. Soc. 2001, 23, 441] for the same systems in which the calculated pressures were too low. The calculated pressures in the NpT ensemble MD simulations are close to 1 atm and the volume of each system increases with increasing temperature. The first and second peaks in the center of mass g(r) diminish gradually and the minima increase as usual for the three liquids as the temperature increases. The three peaks of the site-site gC-C(r) at 283.15 K support the perpendicular structure of nearest neighbors in liquid benzene. Two self-diffusion coefficients of liquid benzene via the Einstein equation and via the Green-Kubo relation are in excellent agreement with the experimental measures. The self-diffusion coefficients of liquid toluene and p-xylene are in accord with the trend that the self-diffusion coefficient decreases with increasing number of methyl group. The friction constants calculated from the force auto-correlation (FAC) function with the assumption that the fast random force correlation ends at time which the FAC has the first negative value give a correct qualitative trends: decrease with increase of temperature and increase with the number of methyl group. The friction constants calculated from the FAC's are always less than those obtained from the friction-diffusion relation which reflects that the random FAC decays slower than the total FAC as described by Kubo [Rep. Prog. Phys. 1966, 29, 255].

• Bulletin of the Korean Chemical Society
• /
• 제23권11호
• /
• pp.1595-1603
• /
• 2002

In this paper we have presented the results of diffusion behavior of model systems for eight liquid n-alkanes ($C_{12}$-$C_{44}$) in a canonical (NVT) ensemble at several temperatures using molecular dynamics simulations. For these n-alkanes of small chain length n, the chains are clearly <$R_{ee}^2$>/6<$R_g^2$>>1 and non-Gaussian. This result implies that the liquid n-alkanes over the whole temperatures considered are far away from the Rouse regime, though the ratio becomes close to the unity as n increases. Calculated self-diffusion constants $D_{self}$ are comparable with experimental results and the Arrhenius plot of self-diffusion constants versus inverse temperature shows a different temperature dependence of diffusion on the chain length. The global rotational motion of n-alkanes is examined by characterizing the orientation relaxation of the end-to-end vector and it is found that the ratio ${\tau}1/{\tau}2$ is less than 3, the value expected for a isotropically diffusive rotational process. The friction constants ${\xi}$of the whole molecules of n-alkanes are calculated directly from the force auto-correlation (FAC) functions and compared with the monomeric friction constants ${\xi}_D$ extracted from $D_{self}$. Both the friction constants give a correct qualitative trends: decrease with increasing temperature and increase with increasing chain length. The friction constant calculated from the FAC's decreases very slowly with increasing temperature, while the monomeric friction constant varies rapidly with temperature. By considering the orientation relaxation of local vectors and diffusion of each site, it is found that rotational and translational diffusions of the ends are faster than those of the center.

• 한국해양공학회지
• /
• 제22권5호
• /
• pp.83-86
• /
• 2008

This paper deals with the experimental works for the correlations of ice resistance for icebreaker with synthetic(model) ice in general towing tank and with refrigerated ice in ice tank. In order to find out the correlation, the density variation is mainly focused in the present study. The model of Terry-Fox ice breaker has been used for the present correlation study because many data are available to be compared. According to the increase of density, the correlation becomes better quantitatively as well as qualitatively. Other parametric studies such as an ice size, a friction coefficient, a bending moment, etc., are also expected to be carried out to have better correlation in a near future. This research could be the basis for the possibility of resistance test using a synthetic ice in a general towing tank instead of an expensive ice tank.

• 터널과지하공간
• /
• 제25권1호
• /
• pp.24-36
• /
• 2015

거창화강암은 국내 주요 석재자원의 하나로서 토목 및 건축사업에 널리 사용되고 있다. 본 연구에서는 거창화강암을 대상으로 수많은 실내시험을 실시하여 암석의 단위중량, 흡수율, P파 속도, S파 속도, 일축압축강도, 인장강도, 영률, 포아송비, 점착력, 내부마찰각, 점하중강도지수 등의 물리적 성질을 조사하였다. 일축압축강도는 인장강도의 19.5배, 점착력의 8.6배이고, P파 속도는 S파 속도의 1.5배 수준이었다. 실험결과로 얻어진 각종 물성간의 상호관계를 분석하였으며, 일축압축강도는 포아송비, 점하중강도지수, 영률과 0.8 이상의 피어슨 상관계수를 보였다. 또한, 단순회귀분석과 다중회귀분석을 통해 물성간의 각종 회귀식을 구하였으며, 특히 결정계수 0.7이상의 회귀식을 정리하여 나타내었다.

• 한국전기전자재료학회논문지
• /
• 제17권10호
• /
• pp.1049-1055
• /
• 2004

Chemical Mechanical Polishing (CMP) is referred to as a three body tribological system, because it includes two solids in relative motion and the CMP slurry. On the assumption that the abrasives between the pad and the wafer could be a major reason not only for the friction force but also for material removal during polishing, the friction force generated during CMP process was investigated with the change of abrasive size and concentration of CMP slurry. The threshold point of average coefficient of friction (COF) with increase in abrasives concentration during interlayer dielectric (ILD) CMP was found experimentally and verified mathematically based on contact mechanics. The predictable models, Mode I (wafer is in contact with abrasives and pad) and Mode II (wafer is in contact with abrasives only), were proposed and used to explain the threshold point. The average COF value increased in the low abrasives concentration region which might be explained by Mode I. In contrast the average COF value decreased at high abrasives concentration which might be regarded to as Mode II. The threshold point observed seemed to be due to the transition from Mode I to Mode II. The tendency of threshold point with the variation of abrasive size was studied. The increase of particle radius could cause contact status to reach transition area faster. The correlation between COF and material removal rate was also investigated from the tribological and energetic point of view. Due to the energy loss by vibration of polishing equipment, COF value is not proportional to the material removal rate in this experiment.

• 대한안전경영과학회지
• /
• 제16권3호
• /
• pp.267-271
• /
• 2014

The objectives of this study were to evaluate the safe criteria of portable slipmeter using human perception onto the several different floor surfaces under contaminated conditions. It was difficult to find why many different slipmeters took there's own safe criteria. It is still unclear how thres hold values established in many literatures. Two different subjective slippery evaluating methods, AHP(Analytic Hierarchy Process) and Friedman test,were used to evaluate the perception of slipperiness of seven different floor surfaces under the contaminated condition with detergent solution. Twelve subjects worn same footwear and walked with self-selected step and cadence along the test floors. The SCOF(Static Coefficient of Friction) obtained for same test conditions with BOT-3000 was compared to perception of slipperiness to establish as a safe criteria. The very high significant correlation(r=0.97) was found between AHP and Friedman test. Also, The high significant correlation(r=0.96) was found between AHP and SCOF obtained with BOT-3000. The results suggested that the SCOF should be greater than 0.63 for safer walking. Perception rating obtained with AHP showed a high correlation with Friedman test and the SCOF obtained with BOT-3000 except for polished tile floor. The safe criteria obtained through this study were similar to ANSI/NFSIB101.1.