• International Journal of Fluid Machinery and Systems
• /
• 제4권2호
• /
• pp.262-270
• /
• 2011

Experimental and numerical investigations were conducted for an internal flow in an axial flow stator of a diagonal flow fan. A corner separation near the hub surface and the suction surface of a stator blade was focused on, and further, three-dimensional vortices in separated flow were investigated by the numerical analysis. At low flow rate of 80% of the design flow rate, a corner separation of the stator between the suction surface and the hub surface can be found in both experimental and calculated results. Separation vortices are observed in the limiting streamline patterns both on the blade suction and on the hub surfaces at 80% of the design flow rate in the calculated results. It also can be observed in the streamline pattern that both vortices from the blade suction surface and from the hub surface keep vortex structures up to far locations from these wall surfaces. An attempt to explain the vortices within a three-dimensional separation is introduced by using vortex filaments.

• 한국전자파학회논문지
• /
• 제10권3호
• /
• pp.340-350
• /
• 1999

본 논문에서는 코너 리플렉터 안테나 구조로부터 변형된 W형 리플렉터 안테나를 제안하고, 모멘트법을 이용하여 복사특성을 해석하였다. 해석결과로 W형 리플렉터 안테나의 다이폴 높이 h와 back edge 거리 d를 변화시켰을 때 복사특성인 이득, 전후방비, 빔폭, 복사패턴을 각각 나타냈다. 또한 W형 리플렉터 안테나와 동일한 크기의 side 반사판을 갖는 코너 리플렉터 안테나의 복사특성을 비교한 결과 W형 리플렉터 안테나가 코너 리플렉터 안테나에 비해 다소 높고, 전후방비가 큼을 알 수 있었다. W형 리플렉터 안테나를 실제 제작하고, 복사특성을 측정하여 계산결과와 비교하였으며, 측정결과는 계산결과에 거의 근접한 것으로 나타났다.

• 제어로봇시스템학회논문지
• /
• 제21권7호
• /
• pp.602-608
• /
• 2015

This paper proposes an algorithm for precise detection of corner points on a coplanar checkerboard in order to perform stereo camera calibration using a single frame. Considering the conditions of automobile production lines where a stereo camera is attached to the windshield of a vehicle, this research focuses on a coplanar calibration methodology. To obtain the accurate values of the stereo camera parameters using the calibration methodology, precise localization of a large number of feature points on a calibration target image should be ensured. To realize this demand, the idea with respect to a checkerboard pattern design and the use of a Homography matrix are provided. The calibration result obtained by the proposed method is also verified by comparing the depth information from stereo matching and a laser scanner.

• 한국정보처리학회논문지
• /
• 제5권3호
• /
• pp.824-832
• /
• 1998

본 논문에서는 영상의 코너점을 추출하기 위한 방법을 제안한다. 먼저 윤곽선을 따라 경계화소의 방향각을 lookup table의 참조에 의해 구하고, 기준치 이상의 화소를 후보점으로 선정한 뒤, 면적편차를 이용하여 코너점을 추출한다. 본 방법은 실시간 처리를 위해 처리시간을 줄이는 동시에 디지털 영상을 표현하는데 있어 라운드 오프 오차에 의해 발생되는 한 화소차를 극복하는 장점을 가진다. 제안된 방법의 검증을 위해 각종 실험 패턴을 이용하여 기존의 방법과 비교분석을 하였다.

• 대한기계학회논문집B
• /
• 제25권3호
• /
• pp.405-413
• /
• 2001

The present study investigates convective heat/mass transfer and flow characteristics inside a rotating two-pass rectangular duct. A naphthalene sublimation technique is employed to determine the detailed local heat transfer coefficients using the heat and mass transfer analogy. The objective of this study is to determine the effects of turning geometry with rotation for 0.0$\leq$Ro$\leq$0.24. The results reveal that the sharp-turn corner has the larger pressure drop and lower heat transfer in the post-turn region than those of the round-turn corner. The strong secondary flow enhances heat transfer for the round-turn corner. Coriolis force induced by the rotation pushes the high momentum core flow toward the trailing wall in the first passage with radially outward flow and toward the leading wall in the second passage with radially inward flow. Consequently, the high heat transfer rates are generated on the trailing surface and the leading surface in the first and second passage, respectively. However, the strong secondary flow due to the turning dominates the flow pattern in the second passage, thus the heat transfer differences between the leading and trailing surfaces are small with the rotation.

• International Journal of CAD/CAM
• /
• 제3권1_2호
• /
• pp.1-12
• /
• 2003

When milling concave corners, cutter load increases momentarily and fluctuates severely due to concentration and uneven distribution of material stock. This abrupt change of cutter load produces undesirable machining results such as wavy machined surface and cutter breakage. An important factor for studying cutter load in 2.5D pocket milling is the instantaneous Radial Depth of Cut (RDC). However, previous work on RDC under different corner-cutting conditions is lacking. In this different corner shapes. In our work, we express RDC mathematically in terms of the instantaneous cutter engage angle which is defined as Cutter Swept Angle (CSA). An analytical approach for modeling CSA is explained. Finally, examples are shown to demonstrate that the proposed CSA modeling method can give an accurate prediction of cutter load pattern at cornering cut.

• Journal of the Optical Society of Korea
• /
• 제16권3호
• /
• pp.221-227
• /
• 2012

We propose optical proximity corrections (OPCs) for digital micromirror device (DMD)-based maskless lithography. A pattern writing scheme is analyzed and a theoretical model for obtaining the dose distribution profile and resulting structure is derived. By using simulation based on this model we were able to reduce the edge placement error (EPE) between the design width and the critical dimension (CD) of a fabricated photoresist, which enables improvement of the CD. Moreover, by experiments carried out with the parameter derived from the writing scheme, we minimized the corner-rounding effect by controlling light transmission to the corners of a feature by modulating a DMD.

• Progress in Superconductivity
• /
• 제6권2호
• /
• pp.113-117
• /
• 2005

In this study, electromagnetic analysis of current paths including meander pattern, spiral pattern, and bi-spiral pattern were performed and in order to verity the analysis results, experiments tests including quench test, and insulation tests were performed. In addition, bubble corner concepts were introduced to enhance insulation reliability. From our study, bi-spiral pattern of YBCO thin films were rather effective for quench and insulation than the other patterns. So this current path pattern was adopted for YBCO thin films in order to develop 6.6 kV resistive fault current limiters. Finally YBCO thin films were connected in series and parallel to enhance capacity, and the test results of current limiting characteristics of 6.6kV resistive SFCL were successful. The Progress in Superconductivity is published every six month and serves as a channel for publications on superconductivity and related topics. The author(s) are required to submit THREE copies of the manuscripts along with original figures directly to the Editor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.218-223
• /
• 1993

An UBET(Upper Bound Elemental Technique) program has been developed to analyze forging load, die-cavity filling and effective strain distribution for flashless forging. To analyze the process easily, it is suggested that the deformation is divided into two different parts. Those are axisymmetric part in corner and plane-strain part in lateral. The total power consumption is minimized through combination of two deformation parts by building block method, from which the upper-bound forging load, the flow pattern, the grid pattern, the veocity distribution and the effective strain are determined. To show the merit of flashless forging, the result of flashless and flash forging processes are compared through theory and experiment. Experiments have been carried out with plasticine billets at room temperature. The theoretical predictions of the forging load and the flow pattern are in good agreement with the experimental results.

• 한국기계가공학회지
• /
• 제12권1호
• /
• pp.28-34
• /
• 2013

For the senses of beauty and texture, internal components of small passenger cars are manufactured by texturing plastic with drawplate but those of deluxe passenger cars are manufactured by bonding pre-embossed skin to the surface of drawplate. As the pre-embossed skin is bonded at high temperature and pressure, the pattern of skin is distorted. The corner part is hardened and its dimension tolerance is changed by resulting in the increase with its defective rate. This study provides the method to design and manufacture the door trim track by vacuuming the non-patterned skin to upper-side drawplate which forms the pattern of descending skin. It is pressed to the plastic product with hot-press method and the damage of bossed-pattern is prevented. Valuation in this study has been done by analyzing, designing and experimenting method.