• Structural Engineering and Mechanics
• /
• v.51 no.1
• /
• pp.181-197
• /
• 2014

Stress determination is a very important step in the assessment of the safety of existing reinforced concrete structures. In rock mechanic this goal is achieved with the over-coring technique. The main idea behind such a technique is to isolate a material sample from the stress field in the surrounding mass and monitor its re-equilibrium deformation response. If the materials remains elastic, and elastic properties are known, stresses may be obtained from the corresponding measured strains. The goal of this paper is to evaluate if the over-coring technique is applicable to reinforced concrete members. The results of an experimental investigation on the behaviour of compressed concrete columns subjected to the over-coring technique are presented. Considerations about the range of applicability of the technique are made by comparing the measured and the theoretical stresses. After that, results of failure tests on drilled specimens are presented and discussed. Furthermore, the response is compared with that of columns core-bored before the compressive test. Finally, comparisons with numerical analysis are shown.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.147.1-147.1
• /
• 2011

지식경제부 가스 하이드레이트 개발사업의 일환으로 동해 울릉분지 가스 하이드레이트 2차 시추(Ulleung Basin Gas Hydrate Drilling Expedition: UBGH2)가 2010년 7월 8일부터 9월 30일까지 D/V Fugro Synergy를 이용하여 수행되었다. UBGH2 수행을 위해 선정된 13개 site에서 약 1개월 동안 Schlumberger사의 장비를 이용 Logging-While-Drilling/Measurement-While-Drilling(LWD/MWD) 자료를 취득하였다. LWD/MWD 자료는 선상에서 분석되었으며, 이 결과는 coring 및 borehole plan 수립을 위하여 활용되었다. Coring Phase 동안 10개 site의 18개 hole로부터 퇴적물 코어 시료를 채취하고 선상에서 퇴적학, 지구화학, 생지화학, 물리적 특성 등 각종 분석과 측정 작업을 수행하였다. 약 2개월에 걸쳐 수행된 coring phase 동안에 2개 site에서 FAOL(Fugro Alluvial Offshore Limited)사의 장비를 이용 Wireline Logging/Vertical Seismic Profile(WL/VSP) 자료도 취득하였다. LWD/MWD phase와 coring phase 동안 12개 site에서 무인잠수정(remotely operated vehicle: ROV)를 이용하여 퇴적물 시료 채취, 해저면 관찰, 용존메탄 측정 등의 작업을 수행하였으며, 선상에서 취득된 이들 자료를 분석하였다. Coring을 수행한 모든 site에서 가스 하이드레이트 부존을 확인하였으며, 다양한 산상의 가스 하이드레이트 실물을 회수하고 분석하였다.

• Journal of the Korean Mathematical Society
• /
• v.48 no.3
• /
• pp.627-639
• /
• 2011

Hopf corings are dened in this work as coring objects in the category of algebras over a commutative ring R. Using the Dieudonn$\'{e}$ equivalences from [7] and [19], one can associate coring structures built from the Hopf algebra $F_p[x_0,x_1,{\ldots}]$, p a prime, with Hopf ring structures with same underlying connected Hopf algebra. We have that $F_p[x_0,x_1,{\ldots}]$ coring structures classify thus Hopf ring structures for a given Hopf algebra. These methods are applied to dene new ring products in the Hopf algebras underlying known Hopf rings that come from connective Morava ${\kappa}$-theory.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.176-181
• /
• 2004

EAF (Electric Arc Furnace) dust is classified as special wastes containing heavy metal contaminants may cause to damage an environment such as underground water contamination if they were not treated properly. For reutilizing the EAF dust, the porous body was made from EAF dust/clay composition system, and analyzed pore characteristics. It was found that a light-aggregate body was made up two different microstructures. One was non-black and dense microstructure which located near surface, and the other was black and porous microstructure (black coring) which located inner part. For systematizing the relationship of the black-coring area and the bloating degree, we defined the Ic(core index) and Is(shell index). It was found that the optimal bloating conditions of artificial light-weight aggregate were more than 0.5 of Ic and 0.4 of Is.

• Proceedings of the KIEE Conference
• /
• 2006.07e
• /
• pp.89-90
• /
• 2006

Recent earth systems not only make earth resistance decreased by installing earth electrode but also are demanded by earth construction for the protection of human life and equipments through total investigation about circumstances. Layer constructions in Jeju island consist of multi-layer of scoria, rocks and shale except clay layers on the surface, which needs the construction of the coring earth electrode suitable in the condition of the area. For this reason, we've used the coring earth electrode. But the coring earth electrode is expected to slow down the performance of this equipment according to the progress of time changing the effects. It is also applied for the stability of earth system construction and management after the construction work analyzing the condition of the earth system. Therefore, this is actually focused on the analysis on measuring the earth resistance and the soil resistivity that cover the range where the remarkable contrast can be expected to be seen in the layer structures.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.361-364
• /
• 2002

This paper discusses the influencing factors such as coring position, height to diameter ratio of core specimen(h/d) and coring torque on the strength estimation of concrete by small site coring method in order to verify the validities of small size core method. According to results, as for the influence of drilling position, when core specimens are obtained from the place parallel to placing direction, compressive strength of core specimens are higher than those perpendicular to placing direction. This is due to the loss of the area of core specimen perpendicular to plating direction by bleeding. And in case of $\phi$ 24mm core specimen, when vertical drilling against placing direction is taken. compressive strength of core specimen obtained at the bottom of the structure is higher than that at the top of the structure. As for the influence of height to depth ratio, as h/d ratio increases compressive strength shows to be decreased. As for the influences of rotation speed of drilling machine, as its speed goes up, compressive strength decreases, regardless of core diameter.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.1
• /
• pp.73-79
• /
• 2011

In this study, coring with diamond core drill on the sintered $Al_2O_3$ ceramic plate were carried out with different coring conditions such as various cutting speed and feed rate to evaluate their effectiveness on the wearing behavior of diamond tool and coring quality. The wearing rate of diamond core drill were getting better with increasing cutting speed and feed rate but the quality of cored hole were getting worse as increasing cutting speed and feed rate.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.253-263
• /
• 2005

There were no cases to use CJM Grouting to Reduce the Permeability of open-cut in Alluvium adjacent to Han River. In this paper, the applicability of CJM Grouting to Reduce the Permeability in Alluvium is reasonably estimated by in-situ Permeability test and coring. It is known that the range of improvement is decided by injection pressure, time of high pressure water and by slump, injection pressure of injection materials.

• Horticultural Science & Technology
• /
• v.16 no.2
• /
• pp.242-243
• /
• 1998

This research was conducted to find the most effective and economical artificial propagation method of Lycoris squamigera among chipping, half-chipping, twin-scaling, coring, scooping and notching, in order to investigate the number of bulblets obtained from one bulb and the number of bulbs treated by a man in a day for artificial propagation. We got 42.2 bulblets from one bulb by twin-scaling, 23.2 bulblets by half-chipping, 18.2 bulblets by chipping, 14.3 bulblets by notching, 1 bulblet by coring and also 1 bulblet by scooping. Although we got the most bulblets by twin-scaling, it took the most time to treat the bulbs for artificial propagation (200 bulbs per day) and the bulblets formed were very small. But 400 bulbs were treated in a day by chipping and the bulblets formed were comparatively large. In addition, machines could be used for chipping, so chipping was considered to be the most effective and economical artificial propagation method.

• Journal of Korean Society of Forest Science
• /
• v.99 no.5
• /
• pp.682-685
• /
• 2010

Coring has been widely used to measure annual increment in temperate forest ecosystems. This method is attractive because cores can be taken in just one visit. However, the accuracy of this method has not been tested. We expected coring to be less accurate than band dendrometers because of the eccentricity of tree growth. We studied 41 trees at the Long Term Experimental Forest in Mt. Gyebang, which has been monitored with band dendrometers since 1996. We collected two tree cores from the south and north face of each tree, 10 cm below the growth band. Increment cores were measured to 0.01 mm under stereomicroscopy. Annual growth from 1997 to 2006 was 3.2 mm $yr^{-1}$ for Quercus mongolica, 3.5 mm $yr^{-1}$ for Kalopanax septemlobus, and 5.7 mm $yr^{-1}$ for Pinus densiflora. The difference between the two methods was 10% for Q. mongolica, 14% for K. septemlobus, and 4% for P. densiflora. Compaction in the corer and shrinkage during drying decreased diameter increment by 5.6% and 1.0% on P. densiflora, respectively. This study suggests that the two methods for annual increment measurement are very similar, but species specificity should be concerned for direct comparison.