• Steel and Composite Structures
• /
• v.30 no.2
• /
• pp.81-96
• /
• 2019

The behavior of a new Three-Tube Buckling-Restrained Brace (TTBRB) with circumference pre-stress (${\sigma}_{{\theta},pre}$) in core tube are investigated through a verified finite element model. The TTBRB is composed of one core tube and two restraining tubes. The core tube is in the middle to provide the axial stiffness, to carry the axial load and to dissipate the earthquake energy. The two restraining tubes are at inside and outside of the core tube, respectively, to restrain the global and local buckling of the core tube. Based on the yield criteria of fringe fiber, a design method for restraining tubes is proposed. The applicability of the proposed design equations are verified by TTBRBs with different radius-thickness ratios, with different gap widths between core tube and restraining tubs, and with different levels of ${\sigma}_{{\theta},pre}$. The outer and inner tubes will restrain the deformation of the core tube in radius direction, which causes circumference stress (${\sigma}_{\theta}$) in the core tube. Together with the ${\sigma}_{{\theta},pre}$ in the core tube that is applied through interference fit of the three tubes, the yield strength of the core tube in the axial direction is improved from 160 MPa to 235 MPa. Effects of gap width between the core tube and restraining tubes, and ${\sigma}_{{\theta},pre}$ on hysteretic behavior of TTBRBs are presented. Analysis results showed that the gap width and the ${\sigma}_{{\theta},pre}$ can significantly affect the hysteretic behavior of a TTBRB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2569-2578
• /
• 2009

Core-A microprocessor is the all-Korean product designed as 32-bit embedded RISC microprocessor developed by KAIST and supported by the Industrial Property Office. This paper analyze Core-A microprocessor architecture and proposes efficient method to interface Core-A microprocessor with coprocessor. To verify proposed interfacing method, the AES cryptography processor that has 128-bit key and block size is used as a coprocessor. Coprocessor and AES are written in Verilog-HDL and verified using Modelsim simulator. It except AES module consists of about 3,743 gates and its maximum operating frequency is about 90Mhz under 0.35um CMOS technology. The proposed coprocessor interface architecture is efficiency to send data or to receive data from Core-A to coprocessor.

• Journal of the Korean Mathematical Society
• /
• v.39 no.5
• /
• pp.745-764
• /
• 2002

In this paper we Study a time-optimal model of pursuit in which the players move on a plane with bounded velocities. This game is supposed to be a nonzero-sum group pursuit game. The main point of the work is to construct and compare cooperative and non-cooperative solutions in the game and make a conclusion about cooperation possibility in differential pursuit games. We consider all possible cooperations of the players in the game. For that purpose for every game $\Gamma(x_0,y_0,z_0)$ we construct the corresponding game in characteristic function form $\Gamma_v(x_0,y_0,z_0)$. We show that in this game there exists the nonempty core for any initial positions of the players. The core can take four various forms depending on initial positions of the players. We study how the core changes when the game is proceeding. For the original agreement (an imputation from the original core) to remain in force at each current instant t it is necessary for the core to be time-consistent. Nonemptiness of the core in any current subgame constructing along a cooperative trajectory and its time-consistency are shown. Finally, we discuss advantages and disadvantages of choosing this or that imputation from the core.

• Nuclear Engineering and Technology
• /
• v.31 no.4
• /
• pp.391-400
• /
• 1999

A conceptual core design of the 1,300MWe KNGR (Korean Next Generation Reactor) without using soluble boron for reactivity control was developed to determine whether it is technically feasible to implement SBF (Soluble Boron Free) operation. Based on the borated KNGR core design, the fuel assembly and control rod configuration were modified for extensive use of burnable poison rods and control rods. A new fuel rod, in which Pu-238 had been substituted for a small amount of U-238 in fuel composition, was introduced to assist the reactivity control by burnable poison rods. Since Pu-238 has a considerably large thermal neutron capture cross section, the new fuel assembly showed good reactivity suppression capability throughout the entire cycle turnup, especially at BOC (Beginning of Cycle). Moreover, relatively uniform control of power distribution was possible since the new fuel assemblies were loaded throughout the core. In this study, core excess reactivity was limited to 2.0 %$\delta$$\rho$ for the minimal use of control rods. The analysis results of the SBF KNGR core showed that axial power distribution control can be achieved by using the simplest zoning scheme of the fuel assembly Furthermore, the sufficient shutdown margin and the stability against axial xenon oscillations were secured in this SBF core. It is, therefore, concluded that a SBF operation is technically feasible for a large sized LWR (Light Water Reactor).

• Nuclear Engineering and Technology
• /
• v.50 no.5
• /
• pp.673-682
• /
• 2018

One of the most widely used methods to estimate core damage during a nuclear power plant accident is containment radiation measurement. The evolution of severe accidents is extremely complex, leading to uncertainty in the containment dose rate (CDR). Therefore, it is difficult to accurately determine core damage. This study proposes to conduct uncertainty analysis of CDR for core damage assessment. First, based on source term estimation, the Monte Carlo (MC) and point-kernel integration methods were used to estimate the probability density function of the CDR under different extents of core damage in accident scenarios with late containment failure. Second, the results were verified by comparing the results of both methods. The point-kernel integration method results were more dispersed than the MC results, and the MC method was used for both quantitative and qualitative analyses. Quantitative analysis indicated a linear relationship, rather than the expected proportional relationship, between the CDR and core damage fraction. The CDR distribution obeyed a logarithmic normal distribution in accidents with a small break in containment, but not in accidents with a large break in containment. A possible application of our analysis is a real-time core damage estimation program based on the CDR.

• Journal of the Korean Society of Systems Engineering
• /
• v.16 no.2
• /
• pp.47-58
• /
• 2020

Most of the reactor trips in Korean NPPs related to core protection systems were caused not because of proximity of boiling crisis and, consequently, a damage in the core, but due to particular miscalculations or component failures related to the core protection system. The most common core protection system applied in Korean NPPs is the Core Protection Calculator System (CPCS), which is installed in OPR1000 and APR1400 plants. It generates a trip signal to scram the reactor in case of low Departure from Nucleate Boiling Ratio (DNBR) or high Local Power Density (LPD). However, is a reactor trip necessary to protect the core? Or could a fast power reduction be enough to recover the DNBR/LPD without a scram? In order to analyze the online calculation of DNBR/LPD, and the use of fast power reduction as trip avoidance methodology, a concept of CPCS with fast power reduction function was developed in Matlab® Simulink using systems engineering approach. The system was validated with maximum of 0.2% deviation from the reference and the dynamic deviation was maximum of 12.65% for DNBR and 6.72% for LPD during a transient of 16,000 seconds.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.29-33
• /
• 2000

The purpose of this paper is to determine the effect of the autoclave inner pressure rate, heat-up rate, tool round angle, Thickness of core, height of joggle on defects, and to minimize the defects of aircraft sandwich structure reinforced with honeycomb core occurred in autoclave processing. The results showed that the geometry of aircraft sandwich structure and tool such as tool round angle, Thickness of core, height of joggle, and the autoclave cure conditions such as inner pressure rate, heat up rate strongly affected the core movement, core wrinkle, bridge phenomenon of prepreg and depression of core that occurred in autoclave processing.

• Journal of Korean Library and Information Science Society
• /
• v.8
• /
• pp.97-126
• /
• 1981

The professional duties of librarians and other information workers involve a generalized body of both theoretical and practical knowledge (the so-called, 'common core') which is a n.0, pplicable worldwide without regard to national boundaries, levels of economic and technical development or cultural context. The current study is an attempt to validate and su n.0, pport this common core concept through a detailed examination of its important role in the sound development of library and information science both as a learned subject and as a profession. Following an initial overview of generally agreed upon core areas in the education and training of librarians and information specialists, with particular attention to the manifold social changes rapidly being effected by computers and communication technology, the focus shifts to the proliferation of academic homes for information science education and its implications for core areas in information science. Of note here is the relationship between information science as a broadly accepted social science discipline and the evolving core curriculum in library schools. To this regard the fact that the popularization of computers and communication technology is increasingly blurring the once-sharp differences between traditional librarians and information specialists naturally favors common core concept. Major figures in library and information science education such as Shera, Saracevic and Foskette su n.0, pport this concept and have already identified its theoretical infrastructure. Finally, UNESCO and IFLA are also stressing the common core cure curriculum for library and information science both as guidelines for the Third World and as a means to achieve universally accepted academic standards. In conclusion, the search for a comprehensive common core curriculum in library and information science education is still in the elementary stages. The task of identifying the components of this common core is among the most crucial responsibilities facing today's educators and professionals for the successful elaboration of a common core would enable us to attain three highly desirable professional goals: 1) To determine the basic concepts and principles of library and information science. 2) To serve as the base for further professional education and specialized research. 3) To offer enhanced o n.0, pportunities for integrated library and information science education programs by providing a genuine two-way communication channel between the library and information science professions.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.1
• /
• pp.56-60
• /
• 2010

Titanium dioxide particles are used as photocatalysts, sensors, adsorbents and catalyst. Core-shell polymers of inorganic/organic pair, which have both core and shell component, were synthesized by sequential emulsion polymerization using Acrylate as a shell monomer and potassium persulfate (KPS) as an initiator. We found that when Acrylate core prepared by adding 0.5~2.0 wt% EU-S133D, Titanium dioxide / Acrylate core-shell polymerization was carried out on the surface of Titanium dioxide particle without forming the new Titanium dioxide particle during acrylate shell polymerized in the inorganic/organic core-shell polymer preparation. The structure of core-shell polymer were investigated by measuring to the thermal decomposition of polymer composite using thermogravimetric analyzer(TGA) and morphology of latex by scanning electron microscope(SEM).

• 한국생물공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.686-686
• /
• 2005