• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.633-636
• /
• 1999

In this study, we have fabricated amorphous FeZrBAg thin films with low core losses by using DC magnetron sputtering method. After deposition, rotational field annealing (RFA) method was performed in the dc field of 1.5 kOe. The amorphous FeZrBAg thin films produced by annealing at 35$0^{\circ}C$ was founded to have high permeability of 8680 at 100 MHz, 0.2 mOe, low coercivity of 0.86 Oe high magnetization of 1.5 T and very low core loss of 1.3 W/cc at 1 MHz, 0.IT respectively. Excellent soft magnetic properties in a amorphous FeZrBAg thin films in the present study are presumably the homogeneous formation of very fine bcc $\alpha$-Fe crystalline with the 8.2 nm in an amorphous FeZrBAg thin film matrix.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1071-1073
• /
• 2005

This paper investigates magnetic field behavior and its iron losses in the stator core using electrical steels. The analysis model is a brushless motor with the permanent magnet. The elliptical rotating and alternating flux distributions with non-sinusoidal waveforms are obtained by Finite Element Method and then their harmonic components are extracted. Based on these results, the local iron losses in the stator core caused by the harmonic flux are calculated. Furthmore, this paper explains the relation between the complex flux waveform and iron loss produced in each part of the stator core.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.882-883
• /
• 2011

This paper deals with comparison on Electromagnetic losses of slotted and slotless high-speed PM Machine for Micro Turbine. Losses are consist of core losses, copper losses and eddy current losses. We are using both analytical method and 2D Finite Element Method for more detailed losses analysis. And then We compare Electromagnetic losses of slotted and slotless PM synchronous machine. This machine has designed of a generator of 800W, 400000rpm and a starter of 400W, 200000rpm.

• Structural Engineering and Mechanics
• /
• v.2 no.1
• /
• pp.63-80
• /
• 1994

A cable is considered as a system of helical wires and a core with distributed dry friction forces at their interfaces. Deformations of the cable subjected to a uniform bending are analyzed. It is shown that there is a critical bending curvature when a slip at the wire-core interface occurs. It originates at the neutral axis of the cross section of the cable and then spreads symmetrically over the cross section with the increase of bending. The effect of slippage on the cable stiffness is investigated. This model is also used to analyze a cable under the quasi-static cyclic bending. Explicit expression for the hysteretic losses per cycle of bending is derived. Numerical examples are given to show the influence of dry friction and helix angle on the bending stiffness and hysteretic losses in the cable.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.774-775
• /
• 2015

In this paper, a series of electromagnetic analyses carried out for a high efficiency 22.9/0.38kV mold transformer are presented. The simulations were performed in order to calculate the losses which eventually verify the performance(efficiency) of the designed product. Here, losses include core loss, stray losses of non-current carrying metallic structural parts(core plate and clamp), ohmic loss and eddy current loss of current carrying metallic parts(busbars, leads, terminals and windings). The obtained results of the simulations were compared to the test results and showed high level of accuracy. The loss evaluation technology will allow designers avoid any potential over-design or under-design of the high efficiency products, reducing the manufacture cost and development period compared to the conventional experience-based design procedures.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.574-579
• /
• 2000

In this study. an off-design performance prediction program for centrifugal pumps is developed. To estimate the losses in an impeller flow passage, two-zone model and two-element in series(TEIS) model are used. At impeller exit. the mixing process occurs with an increase in entropy. In two-zone model. there are both primary zone and secondary zone for an isentropic core flow and an average of all non-isentropic streamtubes respectively. The level of the core flow diffusion in an impeller was calculated by using TEIS model. While internal losses in an impeller an automatically estimated by using the above models, some empirical correlations far estimating external losses. far example, disk friction loss, recirculation loss and leakage loss are used. In order to analyze the vaneless diffuser flow. the momentum equations for the radial and tangential directions are used and solved together with continuity and energy equations.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.7
• /
• pp.437-443
• /
• 2004

In this work the AC loss measurement setup based on an iron core background magnet, not used in a conventional one, has been successfully developed. To prove its validity, a round-robin test for the same Bi-2223 tape sample among three institutes has been done. The results show that the self-field and magnetization losses from the developed setup well agree with the losses measured at two other institutes of Korea Basic Science Institute and Yokohama National University. The measured magnetization losses for parallel or perpendicular fields can be well predicted from the slab model or the strip model for a filamentary region. However the magnetization losses for longitudinal fields can be rather predicted by the slab model for a decoupled filament. The self-field losses are well explained by the Norris ellipse model.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.55-57
• /
• 1998

A finite element analysis for a synchronous reluctance motor (SynRM) is presented with emphasis on the effect of saturation and iron losses. Preisachs model, which allows accurate prediction of iron losses, is adopted in this procedure to provide a nonlinear solution. This technique provide significant properties of proposed SynRM under the magnetic saturation and iron losses effect.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.918-919
• /
• 2008

This paper deals with the DC-DC converter with high efficiency using the minimum reactor. In this paper, the proposed convert uses the air core reactor for ZCS(zero currunt switching) which can minimize the core losses and removes the over switching losses by soft switching. The proposed converter is verified by the modes analysis and computer simulation to prove the theoretical background and adequacy.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.630-635
• /
• 1998

This paper establishes in a new unified manner new mathematical models with core(iron) loss factor for two kinds of AC motors, induction and synchronous motors which are supposed to generate torque precisely or/and efficiently under vector controls. Our new models consist of three basic equations consistent with the others such as differential equation describing electromagnetic dynamics, torque equation describing torque generating mechanism, energy transmission equation describing how injected energy is wasted, saved or transmitted where all vector signals are defined in general frame of arbitrary instant angular velocity. It is clearly shown in our models that equivalent core-loss resistance can express appropriately and separately both eddy-current and hysteresis losses rather than mere vague loss. Proposed model of induction motor is the most compact in sense of the number of employed interior states and parameters. This compact model can also represent eddy-current and hysteresis losses of rotor as well as stator. For synchronous motor, saliency is taken into consideration. As well known model for cylindrical motor can be obtained directly from salient one as its special case.