• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.621-622
• /
• 2005

Copper is widely used in electric wire, cable, conductor in electric devices. As the demand for electric power is increasing rapidly, electric power devices are getting amazingly bigger and complicated. The using of light-weight conductor can reduce the size and making cost of the electric devices. In high-frequency application, Electric current the current in a conductor tends to shift to the surface of the conductor, resulting in an uneven current distribution in the inner conductor. In the extreme case the current may essentially concentrate in the "skin" of the inner conductor as a surface current. In high frequency application, therefore, inner area of copper conductor may replace with aluminum conductor, which reduces the weight of conductor. This paper describes the manufacture and evaluation of composite conductors made of copper and aluminum.

• 대한안전경영과학회지
• /
• 제19권4호
• /
• pp.317-322
• /
• 2017

When the heat flux on the heating surface following changing heat condition in the boiling heat transfer system exceeds critical heat flux, the critical heat flux phenomenon is going over to immediately the film boiling area and then it is occurred the physical destruction phenomenon of various heat transfer systems. In order to maximize the safe operation and performance of the heat transfer system, it is essential to improve the CHF(Critical Heat Flux) of the system. Therefore, we have analysis the effect of improving CHF and characteristics of heat transfer following the nanoparticle coating thickness. As the results, copper nanocoating time are increased to CHF, and in case of nano-coatings are increased spray-deposited coating times more than in the fure water; copper nanopowder is increased up to 6.40%. The boiling heat transfer coefficients of the pure water are increased up to 5.79% respectively. Also, the contact angle is decreased and surface roughness is increased when nano-coating time is increasingly going up.

• Restorative Dentistry and Endodontics
• /
• 제16권2호
• /
• pp.18-32
• /
• 1991

The purpose of this study was to observe characteristic properties of amalgam through the polarization curves and SEM images from 4 type amalgams (Amalcap, Shofu spherical. Dispersalloy and Tytin) with 3 different surface finish procedures (polishing, burnishing and carving) by using the potentiostats (EG & GPARC) and SEM (Jeol JSM-35). After each amalgam alloy and Hg was triturated as the direction of the manufacturer by means of mechanical amalgamator (Samki), the triturated mass was inserted into the cylndrical metal mold which was 12 mm in diameter and 10 mm in height and was pressed with $100kg/cm^2$. 4 specimens of each type amalgam were burnished with egg burnisher and another 4 specimens of each type amalgam were carved with Hollenback carver. Above 8 specimens and remaining untreated 4 specimens were stored at room temperature for about 7 days. Untreated 4 specimens of each type amalgam were polished with abrasive papers (Deer) from #400 to #1200 and finally on the polishing cloth with $0.5{\mu}m$ and $0.06{\mu}m$ $Al_2O_3 $ powder suspended water. Anodic polarization measurements was employed to compare the corrosion behaviours of the amalgams in 0.9% saline solution at $37^{\circ}C$. The open circuit potential was determined after 30 minutes immersion of specimen in electrolyte. The scan rate was 1 mV/sec and the surface area of amalgam exposed to the solution was $0.64cm^2$ for each specimen. All the potentials reported are with respect to a saturated calomel electrode (SCE). SEM images of each specimen were taken after + 800 mV (SCE) polarization. The results were as follows: 1. The corrosion potential of high copper amalgam was more anodic than that of low copper amalgam. 2. The polished amalgam were more resistant to corrosion than any other burnished and carved amalgam. 3. In the case of polishing, current density of high copper amalgam was lower than that of low copper amalgam.

• 마이크로전자및패키징학회지
• /
• 제10권1호
• /
• pp.7-11
• /
• 2003

반도체 칩이나 전자제품에 사용되는 부품들은 작동할 때 발열을 하게 되며 발생한 열이 적절히 제거되지 않을 경우 제품 오작동의 원인이 된다. 이러한 열을 제거하기 위해 히트싱크(heatsink)와 냉각 팬 (cooling fan)을 조합한 냉각 구조가 사용된다. 그러나 히트싱크와 냉각 팬의 조합 구조는 복잡한 형상을 취하기 때문에 전기 전자 제품의 소형화 추세에 부응하기에는 어려움이 따른다. 냉각 효율은 히트싱크의 표면적과 히트싱크 제조시 사용된 재료에 따라 달라진다. 일반적인 냉각 구조의 한계를 극복하기 위한 방안으로써, Trach-etched 멤브레인의 표면과 기공(pore)에 무전해 금도금과 구리 도금을 실행하여 크기는 작으면서 표면적을 증가시킨 마이크로 히트싱크를 제조하였다. 제조한 마이크로 히트싱크의 구조는 주사현미경(SEM)과 광학 현미경으로 관찰하였으며, 일반적인 구리보다 열효율이 우수함을 방열 특성 실험을 통해 관찰하였다.

• 설비공학논문집
• /
• 제21권5호
• /
• pp.291-296
• /
• 2009

Ice accumulating system patterned ice-an-coil is the way of refrigerating regenerative materials on the surface of copper-tube inserted into the inside of ice-storage. The study experimented to understand ice-an-coil type ice making characteristics according to changing shape of ice making tube. The experiment were carried out under various conditions, that used brine temperature($-l0^{\circ}C$, $-6^{\circ}C$) brine flow rate(l.0m/s, 1.8m/s) and inlet water temperature($6^{\circ}C$, $12^{\circ}C$) etc. Mass of ice per making area increased according to the decrease of the brine temperature and inlet water temperature, but that was increased according to the increase of the brine flow rate. And I set up two hypotheses and compared the capacity of ice-making of the two cases; each had the same thermal area and one had an round-shaped copper tube but the other had an oval-shaped copper tube.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.120-126
• /
• 2002

The needs of ultra-precisely machined parts are increasing more and more. But the experimental data required to ultra precision machining of nonferrous metal is insufficient. The behavior of cutting in micro cutting area is different from that of traditional cutting because of the size effect. Copper is widely used as optical parts such as LASER reflector's mirror and multimedia instrument. In experimental, after oxygen-free copper is machined by ultra precision machine with natural mono crystal diamond tool (NCD) and synthetic poly crystal diamond tool (PCD), we compared chip formation and tool's wear according to used tool. Also, we researched optimized cutting condition with the results measured according to cutting condition such as spindle speed, feed rate and depth of cut. As a result, the optimal working condition that makes good surface roughness is obtained. The surface roughness is good when spindle speed is above 80 m/min, and feed rate is small and depth of cut is above 0.5 ${\mu}{\textrm}{m}$. In cutting of klystron anode and cavity 3.2 nmRa of surface roughness is obtained.

• 한국대기환경학회지
• /
• 제23권1호
• /
• pp.64-73
• /
• 2007

The catalytic activity of transition metals (Cu, Co, Mn, Fe and Ni) supported on ${\gamma}-Al_2O_3$ for the oxidation of toluene was investigated in the microreactor of fixed-bed type. The catalytic activity of transition metals for the oxidation of toluene turned out to be increasing in the order of Ni$Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene increased with the increasing loadings of copper, reached the maximum activity at 5% loadings of copper, and decreased with higher loadings of copper in the catalysts. The activity of $Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene decreased with the increasing calcination temperatures. This might result from the decreasing surface area of catalysts due to the sintering of copper oxide as well as ${\gamma}-Al_2O_3$ supports. The 5wt% $Cu/{\gamma}-Al_2O_3$ catalysts calcined at $400^{\circ}C$ for 4 hrs in the air showed the highest activity for the oxidation of toluene. Mutual inhibition was observed for the binary mixture of toluene and xylene. The activity of the easy-to-oxidize toluene was greatly decreased while the difficult-to-oxidize xylene was slightly decreased in the binary mixture of toluene and xylene. It might suggest that the inhibition of toluene and xylene in the binary mixture resulted from the competitive adsorption for the adsorbed oxygen on the catalytic surface.

• 한국기계가공학회지
• /
• 제12권4호
• /
• pp.61-68
• /
• 2013

As an advance study for the development of a heat sink for special purpose high power illumination, an investigation was made to find feasibility for the application of copper plated EP to a heat sink of small LED light of less than 10W installed in commercial product. In this study, the plated heat sink with EP copper was fabricated for the conventional LED light. It was used actually for finding heat radiation property and effectiveness of the heat sink accompanied with measurement of luminous intensity. The heat is radiated by transfer and dissipation only through the copper plated surface due to extremely low heat conductivity of EP in case of EP heat sink; however the total area of the plate plays the function of heat transfer as well as heat radiation in case of the aluminum heat sink. It seems that the volume difference of heat radiating material is so big that the temperature $P_1$ is 9.0~12.3% higher in 3W and 42.7~54.0% higher in case of 6W volume difference of heat radiating material is so big that the temperature $P_1$ is 9.0~12.3% higher in 3W and 42.7~54.0% higher in case of 6W even though heat transfer rate of copper is approximately 1.9 times higher than that of aluminum. It was thought that this is useful to utilize for heat sink for low power LED light with the low heating rate. Also, the illumination could be greatly influenced by the surrounding temperature of the place where it is installed. Therefore, it seems that the illumination installation environment must be taken into consideration when selecting illumination. Further study was expected on order to aims at development of an exterior surface itself made into heat radiation plate by application of this technology in future.

• 한국지반환경공학회 논문집
• /
• 제14권10호
• /
• pp.59-64
• /
• 2013

화강풍화토의 풍화강도에 따른 중금속 흡착특성을 규명하기 위해 납과 구리를 이용하여 회분식 흡착실험을 수행하였다. 화강풍화토의 풍화가 진행됨에 따라 용해성이 높은 $SiO_2$, $K_2O$, $Na_2O$의 함량은 감소하며, 산화물인 $Fe_2O_3$의 함량은 증가하는 것으로 나타났으며, 강열감량과 비표면적은 증가하고 투수계수는 감소하는 것으로 나타났다. 화강풍화토의 풍화강도가 증가할수록 비표면적과 점토질 성분이 증가하므로 납과 구리의 흡착량이 증가하는 것으로 나타났다. 화강풍화토에 의한 납과 구리의 흡착속도는 1차 반응속도모델보다 2차 반응속도모델에 의해 적절하게 설명될 수 있는 것으로 나타났다.

• Korean Chemical Engineering Research
• /
• 제50권5호
• /
• pp.885-889
• /
• 2012

본 연구에서는 활성탄소의 이산화탄소 흡착 능력을 향상시키기 위한 아민과 금속산화물 첨가제에 관하여 고찰하였다. 표면 처리한 활성탄소의 물리화학적 특성은 X-ray photoelection specstroscopy (XPS), 질소등온흡착곡선, X-ray diffraction (XRD), BET 장치를 이용하여 분석하였다. 실험결과, 활성탄소 표면의 아민 기능기는 산성가스인 이산화탄소를 선택적으로 흡착하기 위한 염기성 자리로 작용하며, 2차아민을 갖는 기능기가 1차아민에 비하여 이산화탄소흡착능력이 우수함을 확인하였다. 활성탄소에 첨가된 금속산화물은 표면에서 전자 도우너(electron donor) 역할을 하며 알칼리 특성을 지니고, 아민 기능기와 유사하게 이산화탄소 가스와 산-염기 반응을 유도한다. 금속산화물 표면처리를 했을 경우 순수한 활성탄소와 비교하여 이산화탄소 흡착 용량이 85% 증가하였으며, 이러한 결과로 미루어 볼 때 금속산화물 첨가제는 활성탄소의 이산화탄소 흡착능력을 향상시키기 위한 목적으로 아민 첨가제와 병행하거나 대체할 수 있는 물질로 기대된다.