• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.129-129
• /
• 2014

본 연구는 알루미늄 및 구리 캐리어 소재상에 화학 동도금(Chemical Copper)으로 형성된 극박 동박 표면 및 석출막의 특성 평가에 관한 연구이다. 평가에 사용된 극박 동박은 현재 캐리어박 선점률이 높은 M, J, Y사의 제품이다. 최상층 구리 표면에서 조직, 조성, 표면조도를 평가하였고, 단면 평가에서는 copper layer 및 nodule layer, adhesion layer, anti-corrosion layer, release layer, substrate에서의 물성 및 특성을 평가하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 연구회
• /
• pp.88-91
• /
• 2001

The mechanical properties and surface luminous intensities of copper foil have been studied with variation of the amount of additives into the electrolyte. Especially, organic compound of HEC was added from 0.1 to 10ppm for the propose of increasing the mechanical property and the surface state. The total thickness of electrodeposited copper foil was decreased with increasing the amount of organic compounds. There was not so much significant effect of the current density. It has been observed that mechanical property and surface luminous intensity increase with increasing concentration of organic compounds.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1640-1644
• /
• 2006

The first issue that should be overcome in copper process is its poor adhesive strength between pure copper film and glass substrate. In this study, defining the adhesive strength of pure copper film on various substrates and clarifying the key deposition parameters are presented for the investigation of copper process. First, using different kinds of surface plasma treatments were studied and the results showed that the adhesive strength was not improved even though the roughness of glass substrate surface was increased. Second, adding an adhesive layer between glass substrate and pure copper film was used to enhance the adhesion. Based on the data in the present paper, adopting copper alloy film as an adhesive layer can have capability preventing peeling problem in copper process. Besides, Cu/Cu alloy structure could be etched with the same etchant with better taper angle than the one with single layer of Cu. Unlike Cu/Mo structure, there is no residual problem for Cu/Cu alloy structure during etching process. Finally, this structure was examined in electrical test without significant difference in comparison with the conventional metal process.

• 마이크로전자및패키징학회지
• /
• 제18권2호
• /
• pp.43-48
• /
• 2011

구리의 전해정련공정에서의 최대 전류밀도는 350 A/$m^2$ 이며 생산성의 증가를 위해선 고전류밀도가 필요하다. 회전전극(RDE)을 이용하면 구리의 표면 확산층의 두께조절이 가능하게 되며 안정적인 1000 A/$m^2$의 고전류밀도 구리 도 금이 가능하게 된다. 회전 속도 400rpm조건에서 안정적인 고전류밀도 구리 도금이 가능하였다. 구리 전해정련 과정 중 구리표면의 전착특성 향상을 위해 첨가제는 thiourea와 glue가 사용된다. 고전류밀도 조건에서 첨가제의 거동을 알아보기 위 해 구리가 전착되는 영역에서 첨가제의 농도에 따른 potentiodynamic polarization 실험을 하였고, 1000 A/$m^2$ 조건에서 정전류 실험을 하였다. 동일한 선속도를 인가하기 위해 원통형 회전전극을 이용해 구리도금을 하였고, 도금층의 표면조도 측정에서 thiourea가 16 ppm 들어갔을 때 가장 낮은 조도와 안정적인 취성특성을 나타내었다. 첨가되는 glue의 양이 증가할 수록 표면 조도는 증가하였고, 구리도금층의 경도는 큰 차이가 없었다. 결정립 미세화제로 사용되는 thiourea의 첨가량의 증가에 따라 구리의 핵 성장은 미세해졌고, glue 첨가량의 증가에 따라서는 핵 성장이 영향을 받지 않았다.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.410-415
• /
• 1999

The adhesion strength of sputtered copper films to Inconel substrates has been studied using the scratch test. The effects of substrate treatments before deposition such as chemical or ion bombardment etching were investigated by means of a mean critical load derived from a Weibull-like statistical analysis. It was found that the mean critical load was very weak unless the amorphous layer produced by mechanical polishing on the substrate surface was eliminated. Chemical etching in a nitric-hydrochloric acid bath was shown to have practically no effect on the enhancement of the adhesion. In contrast, the addition in this bath of nickel and copper sulphates allowed removal of the amorphous layer and an increase in the values of the mean critical load. However, it was observed that excessive chemical etching could cancel out the mean critical load enhancement. The results obtained in the case of ion bombardment etching pretreatments could be far higher than those obtained with chemical etching. Moreover, for a sufficiently long period of ion bombardment etching, the adhesion strength was so high that it was impossible to observe evidence of an adhesion failure.

• 설비공학논문집
• /
• 제12권6호
• /
• pp.533-540
• /
• 2000

Condensation heat transfer characteristics have been investigated experimentally when a water vapor is condensed on the outside of a horizontal copper tube in a condenser. This problem is of particular interest in the design of a LiBr-water absorption system. Hydrophilic surface modification was performed to increase the wettability on the copper tube. The optimum hydrophilic treatment condition using acethylene and nitrogen as reaction gas is also studied in detail. The results obtained indicate that the optimum reaction gas ratio of acethylene to nitrogen for hydrophilic surface modification was found to be 7 : 3 for the best condensation heat transfer. In the wide ranges of coolant inlet temperatures, and coolant mass flow rates, both the condensation heat transfer rate and the condensation heat transfer coefficient of a hydrophilic copper tube are increased substantially, compared with those of a conventional copper tube used in a condenser. It is also found that the condensation heat transfer enhancement by the hydrophilic surface modification still emains even after a hundred cycles of wet/dry processes.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권4호
• /
• pp.164-168
• /
• 2003

The initial stage of copper electrodeposition has been known to be very important role for morphology and physical properties after final growth. The factors affecting the nucleation are electrode, current density, electrolyte and temperature. Current studies has illuminated the initial nucleation of copper electrodeposition in the viewpoint of the surface status of electrode and analyzed using EIS and SEM observation

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2013년도 춘계학술대회 논문집
• /
• pp.133-134
• /
• 2013

본 연구는 비전도성 소재 상에 무전해 동도금(Electroless Copper)시 수행되는 씨앗층이나 촉매공정 없이 직접 구리 석출물을 얻는 방법 중 하나에 관한 연구이다. 실리콘 웨이퍼상에 확산방지를 위한 Ta 금속확산방지(Metal barrier)막층 형성 후 무전해 동도금에 침지 후 최소한의 전류를 인가한 결과 균일한 구리피막을 얻을 수 있었으며, 표면 및 단면 조직 분석결과 이를 확인할 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.569-570
• /
• 2006

In this study, the characteristics of Electrical Discharge Machining (EDM) with the electrode materials were investigated. EDM experiments have been carried out on electrodes with eight different copper-based and graphite-based materials. From the results, the copper-based electrodes showed excellent surface roughness than the graphite-based electrodes. But graphite based electrodes have advantages in economic aspects.

• KSTLE International Journal
• /
• 제2권1호
• /
• pp.22-28
• /
• 2001

A resin bonded copper-graphite brush was investigated to evaluate the characteristics electrical signal transmission through a sliding contact as a function of the relative amount of graphite and copper in the brush. Particular attention was given to the correlation between electrical signal fluctuation and tribological properties in an electrical sliding contact system. A ring-on-block type tribotester was used for this experiment and the ring was made from pure copper. Results showed that a copper-graphite brush at a particular composition range exhibited the most stable frictional behavior with a minimum voltage drop. The amount of voltage drop at the friction interface was affected by the surface roughness, transfer film formation at the friction interface, and the real area of contact. Microscopic observations and the surface analysis showed a good agreement with the results from this experiment. The results also indicated that the electrical signal flunctuation was directly associated with the oscillation of the coefficient of friction during sliding by nanoscale variation of contacts at the friction interface.