• 접착 및 계면
• /
• 제7권3호
• /
• pp.16-25
• /
• 2006

내열성 및 투습방수기능을 가진 신발용 직물 및 부직포를 제조하기 위하여 스크린 방식으로 공정조건을 검토하고 투습방수 필름을 라미네이팅 한 후, 최종제품의 물성을 평가하였다. 결과는 다음과 같다. 열가소성 핫 멜트와는 달리 반응형 폴리우레탄 핫 멜트는 작업 이후에 적정한 내열성을 보유하는 것으로 나타났다. 최적의 용융접착 공정조건은 다음과 같다 ; 드럼 온도 $95^{\circ}C$, 호스 온도 $97^{\circ}C$, 공급파이프 온도 $100^{\circ}C$, 스크린 온도 $105^{\circ}C$이고, opposite roller의 압력은 $1kgf/cm^2$, laminating roller의 압력은 $3kgf/cm^2$이며, 가공속도는 15 m/min이다. 투습도는 필름의 두께가 증가함에 따라 투습도는 감소하였으나, 내수도는 증가하였고, 공기투과도는 필름의 영향이 지배적이었다.

• 연구논문집
• /
• 통권27호
• /
• pp.87-99
• /
• 1997

Present paper describes on/off design performance of a 50KW turbogenerator gas turbine engine for hybrid vehicle application. For optimum design point selection, relevant parameter study is carried out. The turbogenerator gas turbine engine for a hybrid vehicle is expected to be designed for maximum fuel economy, ultra low emissions, and very low cost. Compressor, combustor, turbine, and permanent-magnet generator will be mounted on a single high speed (82,000 rpm) shaft that will be supported on air bearings. As the generator is built into the shaft, gearbox and other moving parts become unnecessary and thus will increase the system's reliability and reduce the manufacturing cost. The engine has a radial compressor and turbine with design point pressure ratio of 4.0. This pressure ratio was set based on calculation of specific fuel consumption and specific power variation with pressure ratio. For the given turbine inlet temperature, a rather conservative value of $1100^\circK$ was selected. Designed mass flow rate was 0.5 kg/sec. Parametric study of the cycle indicates that specific work and efficiency increase at a given pressure ratio and turbine inlet temperature. Off design analysis shows that the gas turbine system reaches self operating condition at N/$N_{DP}$ = 0.53. Bleeding air for turbine stator cooling is omitted considering low TIT and for a simple geometric structure. Various engine performance simulations including, ambient temperature influence, surging at part load condition. Transient analysis were performed to secure the optimum engine operating characteristics. Surge margin throughout the performance analysis were maintained to be over 80% approximately. Validation of present results are yet to be seen as the performance tests are scheduled by the end of 1998 for comparison.

• 한국기계가공학회지
• /
• 제15권6호
• /
• pp.129-135
• /
• 2016

There have been many types of development and commercialization efforts for superconducting power applications with the continuous development of High Temperature Superconducting (HTS) conductors. In particular, HTS power cables are going to be commercialized in real power grids. A cryogenic refrigeration system should be used to keep it below 77 K, and its required cooling capacity continuously increases as the unit length of the HTS power cable increases. Among the many kinds of cryogenic refrigerator, a reverse Brayton refrigerator that uses turbo expanders is a promising refrigerator due to its efficiency and reliability. Among the various components in refrigerators, the cryogenic turbo-expander is the most important part for increasing efficiency and assuring reliability. The design of a 300 W class turbo-expander is described in this paper prior to the development of a 10 kW class turbo expander, which is the required capability for the commercialization of a HTS power cable. The impeller shape and rotation speed are determined based on the cycle analysis. The Eigen frequency and harmonic analysis are conducted with gas bearings at cryogenic temperatures to determine the operational stability.

• 산업경영시스템학회지
• /
• 제39권1호
• /
• pp.130-139
• /
• 2016

The purpose of this paper is to analyze the problems and the sources of defective products and draw improvement plans in a small plastic boat manufacturing process using TOC (Theory Of Constraints) and statistical analysis. TOC is a methodology to present a scheme for optimization of production process by finding the CCR (Capacity Constraints Resource) in the organization or the all production process through the concentration improvement activity. In this paper, we found and reformed constraints and bottlenecks in plastic boat manufacturing process in the target company for less defect ratio and production cost by applying DBR (Drum, Buffer, Rope) scheduling. And we set the threshold values for the critical process variables using statistical analysis. The result can be summarized as follows. First, CCRs in inventory control, material mix, and oven setting were found and solutions were suggested by applying DBR method. Second, the logical thinking process was utilized to find core conflict factors and draw solutions. Third, to specify the solution plan, experiment data were statistically analyzed. Data were collected from the daily journal addressing the details of 96 products such as temperature, humidity, duration and temperature of heating process, rotation speed, duration time of cooling, and the temperature of removal process. Basic statistics and logistic regression analysis were conducted with the defection as the dependent variable. Finally, critical values for major processes were proposed based on the analysis. This paper has a practical importance in contribution to the quality level of the target company through theoretical approach, TOC, and statistical analysis. However, limited number of data might depreciate the significance of the analysis and therefore it will be interesting further research direction to specify the significant manufacturing conditions across different products and processes.

• 한국식품과학회지
• /
• 제52권4호
• /
• pp.357-362
• /
• 2020

본 연구는 조직감 및 기능성 면에서 우수한 식물성 대체육의 제조를 위하여 부원료로 버섯을 첨가한 압출성형 대체육의 품질특성에 대하여 살펴보았다. 대체육의 원료는 분리대두단백 50%, 글루텐 40%, 옥수수 전분 10%를 섞은 것을 기본배합(base)으로 하였다. 버섯 첨가함량을 기본배합 대비 0, 4, 8, 12%로 한 총 네개의 시료를 수분함량 55%, 스크루 속도 150 rpm, 바렐 온도를 170℃로 하여 냉각 사출구를 통해 20℃로 사출하였다. 압출성형 후 물리적 특성으로 경도, 탄성, 응집성, 씹힘성과 절단 강도, 조직잔사지수, 보수력을 측정하였고, 화학적 특성으로 수용성 질소지수, 단백질 소화율과 DPPH 라디칼 소거활성을 측정하였다. 버섯 첨가함량이 증가함에 따라 경도, 탄성, 응집성, 씹힘성과 절단강도가 모두 증가하였으며, 조직잔사지수 역시 증가하였다. 반면에, 버섯 첨가함량이 증가할수록 보수력과 수용성 질소지수는 감소하였으며, 단백질 소화율도 다소 감소하였다. DPPH 라디칼 소거활성은 버섯 첨가함량의 증가에 따라 유의적인 증가를 나타내었다. 압출성형 대체육에 버섯의 첨가는 대체육의 조직감을 개선하고 항산화 기능성을 부여하는 유효한 공정임을 확인하였다.

• 한국정밀공학회지
• /
• 제17권9호
• /
• pp.189-195
• /
• 2000

RP techniques have their unique characteristics according to the working principles : star-stepped surface of parts due to layer-by-layer stacking low build speed caused by line-by-line solidification to fish one layer and post processing to improve surface finish etc The objective of this study is to propose a new RP technique Variable Deposition Mnanufacturing (VDM) which can make up for the disadvantages of the existing RP techniques and to develop an apparatus to implement the technique. The proposed process can greatly reduce the build time and improve the surface finish of parts generated. Experiments are carried out to obtain the range of temperature of molten material to maintain its fluidity and to investigate the effect of gas cooling on the preservation of the slopes. Some simple shapes such as a line-shape an S-shape and a circle-shape are fabricated from Ethylene Vinyl Acetatecopolymer(EVA) In order to examine the applicability of VDM to more general shapes a tensile specimen and a yo-yo shape were manufactured by the proposed RP method using EVA material as a trial approach. The current basic study shows a high potential of practical use of the proposed VDM process to prototyping of a general three-dimensional shape.

• 대한기계학회논문집A
• /
• 제38권12호
• /
• pp.1373-1377
• /
• 2014

핫스탬핑 공정은 고강도의 강을 얻을 수 있는 방법으로써, 일반적으로 보론강을 오스테나이트 온도까지 가열한 후, 성형과 냉각을 통해 제품을 생산한다. 열처리된 보론강은 1500MPa 이상의 강도를 가지기 때문에 경량화와 안전성을 동시에 향상시킬수 있는 특징이 있다. 뿐만아니라 우수한 성형성으로 인한 치수정밀도가 기존 강판대비 90 % 이상 향상되어 우수한 성형품질을 확보할 수 있는 장점도 있다. 따라서 본 연구에서는 디스크 레이저를 사용하여 핫스탬핑 강판의 맞대기 및 겹치기 용접을 실시하여 용접특성을 파악하였다. 실험결과, 맞대기 용접에서는 맞댄면의 갭에 영향으로 인해 겹치기 용접과 비교하여 더 빠른 속도에서도 완전 용입을 얻을 수 있었으며, 모든 용접부에서 열영향부에서 화이트밴드가 관찰되었다.

• Architectural research
• /
• 제17권3호
• /
• pp.109-115
• /
• 2015

The dynamic pricing of electricity, where the electricity rate increases in a time zone with a high demand for electricity is typically applied to a building whose power reception capacity is greater than a certain size. This includes the time of use(TOU) electricity pricing in Korea which can induce the effect of reducing the power demand of a building. Meanwhile, a VRF (Variable Refrigerant Flow) system that uses electricity is regarded as one of the typical heating and cooling systems along with central air conditioning (central HVAC) for its easy operation and application to the building. Thus, to reduce power energy and operating costs of a building in which the TOU and VRF systems are applied simultaneously, we suggested a control for changing the indoor temperature setting within the thermal comfort range or limiting the rotational speed of an inverter compressor. In this study, to describe the features of the above-mentioned control and verify its effects, we evaluated the results obtained from the analysis of its operation data. Through the actual measurements in winter operations for 73 days since mid- December 2014, we confirmed a reduction of 10.9% in power energy consumption and 12.2% in operating costs by the new control. Also, a reduction of 13.3% in power energy consumption was identified through a regression analysis.

• Ocean Science Journal
• /
• 제42권2호
• /
• pp.103-116
• /
• 2007

Seasonal changes of tide signal(s), temperature, salinity and current were studied during the years 2004-2005 in the northernmost Gulf of Aqaba, which is under developmental activities, to obtain scientific bases for best management and sustainability. Spectrum analysis revealed permanent signals of tide measurements during all seasons, which represented semidiurnal and diurnal barotropic tides. The other signal periods of 8.13, 6.10-6.32, 4.16 and 1.02-1.05 h were not detected in all seasons, which were related to shallow water compound and overtides of principle solar and lunar constituent and to seiches generated in the Red Sea and the Gulf of Aqaba. Spatial and temporal distribution of temperature, salinity and density showed significant differences between months in the coastal and offshore region and no significant differences among the coastal sites, between the surface and bottom waters and between coastal and offshore waters. Therefore, the temporal and spatial variation of water properties in the northernmost Gulf of Aqaba behave similarly compared to other parts. The coastal current below 12 m depth was weak $(3-6\;cms^{-1})$ and fluctuated from east-northeastward to west-southwestward (parallel to the shoreline), which may be related to the effect of bottom topography and/or current density due to differential cooling between eastern and western parts in the study area, and wind-induced upwelling and downwelling in the eastern and western side, respectively. The prevailing northerly winds and stratification conditions during summer were the main causes of the southward current at 6 and 12 m depths with average speed of 28 and $12cms^{-1}$ respectively.

• 한국화재소방학회논문지
• /
• 제31권6호
• /
• pp.83-90
• /
• 2017

전선에 정격이상의 과전류가 흐르게 되면 온도가 상승하고 전선피복이 열화되어 단락현상이 발생한다. 과전류의 크기에 따라 전선의 온도 상한치는 변화하며, 각각의 온도 상한치에서 단락이 발생할 때, 단락온도와 전선표면온도간 온도차로 인해 응고과정에서 냉각속도 차이가 발생한다. 이때 용융단면에 형성되는 수지상 조직의 패턴특징이 상이하게 된다. 본 논문에서는 과전류 크기에 따라 변화하는 전선온도의 상한치를 측정하고, 이때 단락을 발생시켜 수지상의 2차 가지 간격(Dendrite Arm Spacing : DAS)을 분석하여 수치를 정량화 하였다. 실험결과, 과전류 크기가 커짐에 따라 전선온도의 상한치는 증가하였으며, 전선온도가 높아질수록 2차 가지 간격이 증가하는 것을 확인하였다.