• Nuclear Engineering and Technology
• /
• 제53권1호
• /
• pp.93-102
• /
• 2021

The analysis of the fluid flow characteristics in reactor pressure vessel is an important part of the hydraulic design of nuclear power plant, which is related to the structure design of reactor internals, the flow distribution at core inlet and the safety of nuclear power plant. The flow distribution and mixing characteristics in the pressurized reactor vessel for the 1000MWe advanced pressurized water reactor is analyzed by using Computational Fluid Dynamics (CFD) method in this study. The geometry model of the full-scaled reactor vessel is built, which includes the cold and hot legs, downcomer, lower plenum, core, upper plenum, top plenum, and is verified with some parameters in DCD. Under normal condition, it is found that the flow skirt, core plate holes and outlet pipe cause pressure loss. The maximum and minimum flow coefficient is 1.028 and 0.961 respectively, and the standard deviation is 0.019. Compared with other reactor type, it shows relatively uniform of the flow distribution at the core inlet. The coolant mixing coefficient is investigated with adding additional variables, showing that mass transfer of coolant occurs near the interface. The coolant mainly distributes in the 90° area of the corresponding core inlet, and mixes at the interface with the coolant from the adjacent cold leg. 0.1% of corresponding coolant is still distributed at the inlet of the outer-ring components, indicating wide range of mixing coefficient distribution.

• Nuclear Engineering and Technology
• /
• 제55권10호
• /
• pp.3775-3786
• /
• 2023

Mixing Vane Grid (MVG) is one of the most important structures in fuel assembly due to its high performance in mixing the coolant and ultimately increasing Critical Heat Flux (CHF), which avoids the temperature rising suddenly of fuel rods. To evaluate the mixing performance of the MVG, a Total Diffusion Coefficient (TDC) mixing coefficient is defined in the subchannel analysis code. Conventionally, the TDC of the spacer grid is obtained from the combination of experiments and subchannel analysis. However, the processing of obtaining and determine a reasonable TDC is much challenging, it is affected by boundary conditions and MVG geometries. In is difficult to perform all the large and costing rod bundle tests. In this paper, the CFD method was applied in TDC analysis. A typical 5 × 5 MVG was simulated and validated to estimate the mixing performance of the MVG. The subchannel code was used to calculate the TDC. Firstly, the CFD method was validated from the aspect of pressure drop and lateral temperature distribution in the subchannels. Then the effect of boundary conditions including the inlet temperature, inlet velocities, heat flux ratio between hot and cold rods and the arrangement of hot and cold rods on MVG mixing and TDC were studied. The geometric effects on mixing are also carried out in this paper. The effect of vane pattern on mixing was investigated to determine which one is the best to represent the grid's mixing performance.

• Nuclear Engineering and Technology
• /
• 제27권6호
• /
• pp.811-824
• /
• 1995

CANDU 핵연료봉의 휨 열적 휨 멘트와 수력학적 견인력 및 기계적 하중에 기인하는 휨 모멘트에 의하여 일어난다. 여기서, 연료봉 휨은 연료봉 축방향 중심선으로부터의 측면 처짐으로 정의한다. 본 논문에서는 연료봉 축방향 중심선에 대한 비대칭 온도불포에 의해 핵연료 피복관 자체와 피복관과 소결체의 상호작용 부위에서 발생하는 열적 휨만을 취급한다. 이를 위해 1).소결체와 피복관사이의 기계적 상호작용을 무시한 조건에서의 핵연료 피복관의 휨과 2) 소결체와 피복관의 온도 변화에 기인하여 발생하는 소결체와 피복관 사이의 기계적 상호작용을 고려한 조건에서의 연료봉 휨을 혼합 고려하고, 각각에서 피복관의 비대칭 온도분포가 (i) 냉각재의 불완전한 혼합에 따른 비균질 냉각재 온도, (ii) 핵연료 피복관과 냉각재 사이의 비균질한 열전달 계수, (iii) 핵연료내 반경 방향으로의 중성자속 감쇄에 의한 비대칭 열 발생 등의 복합적효과에 의해 발생되는 것으로 고려하여 피복관의 대칭온도 분포까지 포함 할 수 있는 열적 휨의 일반적 해석 공식을 제시하였다. 본 휨 공식에 사용되는 모든 변수에 대한 민감도 분석을 통해, 핵연료봉 길이, 피복관 내경, 냉각재 평균 온도 및 변화 인자, 소결체 -피복관 기계적 상호 작용 인자, 중성자속 감쇄 인자, 핵연료 열팽창 계수, 피복관-냉각재 열전도 계수 등의 변화가 피복관 두께, 피복관-냉각재 열전달 계수, 피복관 열팽창 계수, 핵연료-피복관 열전달 계수 등의 변화보다 핵연료봉의 열적 휨에 상대적으로 더욱 영향을 미치는 것으로 밝혀졌다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.269-274
• /
• 2011

A CFD analysis was performed to examine the inner channel blockage of dual-cooled fuel which has being developed for the power uprate of a pressurized water reactor (PWR). The dual-cooled fuel consists of an annular fuel pellet($UO_2$) and dual claddings as well as internal and external cooling channels. The dual-cooled annular fuel is different from a conventional solid 려el by employing an internal cooling channel for each fuel pellet as well as an external cooling channel. One of the key issues is the hypothetical event of inner channel blockage because the inner channel is an isolated flow channel without the coolant mixing between the neighboring flow channels. The inner channel blockage could cause the Departure from Nucleate Boiling (DNB) in the inner channel that eventually causes a fuel failure. This paper presents the CFD simulation of the flow through the side holes of the bottom end plug for the complete entrance blockage of the inner channel. Since the amount of coolant supply to the inner channel depends on largely the pressure loss at the side hole, the pressure loss coefficient of the side hole was estimated by the CFD analysis. The CFD prediction of the loss coefficient showed a reasonable agreement with an experimental data for the complete blockage of both the inner channel entrance and the outer channel. The CFD predictions also showed the decrease of the loss coefficient as the outer channel blockage increases.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1998년도 춘계학술발표회논문집(1)
• /
• pp.124-129
• /
• 1998

A sensitivity study has been done to determine the composition of DUPIC fuel from the viewpoint of neutronics fuel design. The spent PWR fuel compositions were generated and fissile contents adjusted by blending fresh uranium after mixing two spent PWR fuel assemblies. The $^{239}$ Pu and $^{235}$ U enrichments of DUPIC fuel were adjusted by controlling the amount of fresh uranium feed and the ratio of slightly enriched and depleted uranium in the fled uranium. Based on the material balance calculation, it is recommended that DUPIC fuel composition be such that spent PWR fuel utilization is more than 90%.. A sensitivity study on the temperature reactivity coefficient of DUPIC fuel has shown that it is desirable to increase the $^{239}$ Pu and $^{235}$ U contents to reduce both the fuel and coolant temperature coefficients. On the other hand, refueling simulations of the DUPIC core have shown that the channel power peaking factor, which is a measure of the reactor trip margin, increases with the total fissile content. Considering these neutronic characteristics of the DUPIC fuel, il is recommended to have enrichments of 0.45 and 1.00 wt% for $^{239}$ Pu and $^{235}$ U, respectively.

• Nuclear Engineering and Technology
• /
• 제14권4호
• /
• pp.186-195
• /
• 1982

SYSRAN code를 사용하여 고리 1호기의 중기배관파열사고를 분석하였다. SYSRAN code는 중성자출력과 열선속계산은 각각 점근사 중성자 운동방정식과 집중정수 모형을 이용하고 냉각수 계통 과도현상에 대해서는 전 계통을 균일한 압력으로 취급하여 질량 및 에너지 평형방정식을 이용하여 계산한다. 사고 결과를 심각하게 만드는 노심상태로 부냉각재 온도계수가 커지는 노심말기와 증기발생기의 유체함량이 가장 많은 고온 정지상태를 호기조건으로 하여, 격납용기외부의 가장 큰 배관면적인 1.4f $t^2$ 크기의 증기배관이 파열되었을때 Moody critical flow model에 따라 증기가 방출된다고 가정하여 분석하였다. 그 결과 노심의 최대 열선속은 사고후 60초에 정상상대의 38%로서 FSAR의 26%에 비해 높은 값을 나타냈으나 모든 과도현상의 경향은 FSAR의 결과와 잘 일치하였다. 민감도 조사결과 이 사고는 냉각재밀도 계수와 노심 하부공간혼합인자에 가장 민감한 것으로 나타났다. B bank중 한 개의 RCCA가 완전인출 상태에서 노심에 삽입되지 않았다고 가정했을 경우의 FSAR 분석결과인 $F_{$\Delta$H}$를 3.66으로 Fz를 1.55로 하여 DNBR을 계산해 본 결과, 최소 DNBR은 1.62가 되어 핵연료의 손상은 예상되지 않았다. 점근사중성자 운동방정식, 집중 정수모형 및 질량과 에너지평형 방정식을 이용한 계통 과도 현상모델은 발전소 전 계통의 과도 현상의 경향을 연구하는데 적합한 것으로 밝혀졌다.구하는데 적합한 것으로 밝혀졌다.