• Progress in Superconductivity and Cryogenics
• /
• v.14 no.1
• /
• pp.8-13
• /
• 2012

We already fabricated a proto-type HTS charging system with photovoltaic (PV) system and obtained design parameters for DC converter and HTS charging system. In order to develop the real scale charging system efficiently, we suggested a maximum power point tracking (MPPT) controller using a perturb and observe (P&O) MPPT algorithm for PV system. In this paper, we designed and simulated the MPPT controller for the real scale HTS charging system. As well as, the PV module has been analyzed by solving solar cell equivalent equations. The simulated and theoretical results presented here are being considered the next study which addresses the design and fabrication parameters.

• ETRI Journal
• /
• v.30 no.4
• /
• pp.495-505
• /
• 2008

This paper presents a parallel processing searcher structure for the initial synchronization of a direct sequence ultra-wideband (DS-UWB) system, which is suitable for the digital implementation of baseband functionalities with a 1.32 Gsample/s chip rate analog-to-digital converter. An initial timing acquisition algorithm and a data demodulation method are also studied. The proposed searcher effectively acquires initial symbol and frame timing during the preamble transmission period. A hardware efficient receiver structure using 24 parallel digital correlators for binary phase-shift keying DS-UWB transmission is presented. The proposed correlator structure operating at 55 MHz is shared for correlation operations in a searcher, a channel estimator, and the demodulator of a RAKE receiver. We also present a pseudo-random noise sequence generated with a primitive polynomial, $1+x^2+x^5$, for packet detection, automatic gain control, and initial timing acquisition. Simulation results show that the performance of the proposed parallel processing searcher employing the presented pseudo-random noise sequence outperforms that employing a preamble sequence in the IEEE 802.15.3a DS-UWB proposal.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.665-670
• /
• 2005

This paper introduces the propulsion system(Motor Block) stabilization test result for Korean High Speed Railway(HSR). The developed propulsion system using high power semiconductor, IGCT(Integrated Gate Commutated Thyristor) consists of two PWM converter and VVVF inverter. In this paper, overall configuration of propulsion system is briefly described and stabilization tests are made to verify the developed propulsion system. The presented test results shows beatless control method of inverter output current at the 200km/h and performance test of BCH.

• Proceedings of the IEEK Conference
• /
• 2001.06e
• /
• pp.245-248
• /
• 2001

This paper is indicating the problems, which are the conduction loss on the high frequency transformer, the protection of rectification diode as the snubber loss and the stress of switching main devices, as be made high current and high speed in the phase-shift switching full-bridge DC-DC converter is used the power supply’s main circuit of high capacity. To improve those problems, in this paper, it is proposed that is the resonant circuit auxiliary can be reduced conduction losses and stabilized output control. And, it is constructed prototype of the power supply as the result of computer simulations.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.1
• /
• pp.121-127
• /
• 2012

An electric power compensation system for a DC transmission system with an integrated wind turbine generator is proposed. The proposed compensation system consists of a synchronous generator and a duplex reactor. This apparatus is connected to the sending-end circuit of the DC transmission system. A set of steady-state equations of the system is first derived. Then, the effect of the duplex reactor, which can eliminate the sending-end grid current distortion due to commutation of the converter, is explored. The relationships among power at the sending-end circuit are also revealed. It is shown that fluctuations in the sending-end grid power due to changes in wind velocities are compensated with the proposed system. Finally, the effects of the sending-end grid conditions on the steady-state characteristics of the system are studied.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.369-372
• /
• 2002

전극분할 된 횡진동 모드 압전 진동자에 NIC 회로를 적용한 특성제어 방법을 두께 진동 모드 압전 진동자에 적용하여 그 가능성을 확인해 보았다. 동일한 특성을 가진 두 개의 두께 진동 모드 압전 진동자를 분극방향이 서로 마주보게 제작한 다음, NIC 회로를 적용하여 그 실험결과를 PSpice 모델을 이용한 시뮬레이션과 비교하였다. 그 결과 NIC 회로의 저항 $R-s$,의 변화에 따라 두께 진동 모드 압전 진동자의 품질계수는 제어되었으며, NIC 회로를 적용하지 않은 경우보다 품질계수가 약 18.9배 정도 향상되었다.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.37 no.1
• /
• pp.33-40
• /
• 2014

Air compressor is an important facility with electric power in the industry. However, because of the noise and vibration of air compressor and is installed outside the building management difficulty. In this study, MCP (Micro Control Processor) to remote monitoring of the air compressor via the compressed air through improved quality and allows stable maintenance were designed. So, increase the productivity improvement of energy-saving effect can be obtained. Remote real-time information stored on your PC to manage air compressor equipment was higher reliability. Monitoring system is developed in this study was applied to embedded systems. It is easy to install air compressor, and low maintenance costs was to raise the economic impact.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.185-191
• /
• 2006

Auxiliary power supply developed by domestic technology has very important function that not only effect on main power converter & inverter system, traction motor and train control system which are related to performance of train, but also influence on power supply for HVAC(Heat, Ventilation, Air-conditioning) and lighting device which are related to comfort of passengers. This paper shows characteristic test results of auxiliary power supply such as working condition and performance, which is associated with velocity of train, operating mode and surrounding equipment, through test running. Also it shows the results deduced from comparison analysis between designed data and manufactory test data as measuring in put voltage of auxiliary power supply. And, it propose a modification of design parameter for stabilizing operation and improving reliability.

• Journal of the Korean Society for Railway
• /
• v.10 no.1 s.38
• /
• pp.84-87
• /
• 2007

Auxiliary power supply developed by domestic technology has very important function that not only effect on main power converter & inverter system, traction motor and train control system which are related to performance of train, but also influence on power supply for HVAC(Heat, Ventilation, Air-conditioning) and lighting device which are related to comfort of passengers. This paper shows characteristic test results of auxiliary power supply such as working condition and performance, which is associated with velocity of train, operating mode and surrounding equipment, through test running. And, it propose a modification of design parameter for stabilizing operation and improving reliability.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.4
• /
• pp.36-40
• /
• 2012

This paper presents an experimental and numerical study on current limiting characteristics of a fault current controller (FCC). The FCC consists of an AC/DC power converter, a superconducting coil, and a control unit. Even though some previous researches proved that the FCC could adjust the fault current level, the current limiting characteristics by the superconducting coil should be investigated for design of the coil. In this paper, four kinds of model coils were tested; 1) air core, 2) iron core without any bias, 3) reversely magnetized core (RMC) using permanent magnets, and 4) RMC using an electromagnet. Based on a comparative study, it is confirmed that a RMC by an electromagnet (EM) could increase the effective inductance of the coil. In this paper, a numerical code to simulate the HTS coil with RMC was developed. This code can be applied to design the HTS coil with active reversely magnetized bias coil.